NEC NEAX 2000 IVS2 System Manual

Integrated voice server
Hide thumbs Also See for NEAX 2000 IVS2:

Advertisement

Quick Links

ND-70922 (E)
ISSUE 1
STOCK # 151991
®
Open Application Interface (OAI)
System Manual
JULY, 2000
NEC America, Inc.

Advertisement

Table of Contents
loading

Summary of Contents for NEC NEAX 2000 IVS2

  • Page 1 ND-70922 (E) ISSUE 1 STOCK # 151991 ® Open Application Interface (OAI) System Manual JULY, 2000 NEC America, Inc.
  • Page 2 NEC America, Inc. reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC America, Inc. and shall not be reproduced without prior written approval from NEC America, Inc.
  • Page 3 ISSUE No. ISSUE No. PAGE No. PAGE No. ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4 DATE JULY, 2000 DATE DATE DATE ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8 DATE DATE DATE DATE NEAX2000 IVS Revision Sheet 1/2 Open Application Interface (OAI) System Manual ND-70922 (E)
  • Page 4 ISSUE No. ISSUE No. PAGE No. PAGE No. ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4 DATE JULY, 2000 DATE DATE DATE ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8 DATE DATE DATE DATE NEAX2000 IVS Revision Sheet 2/2 Open Application Interface (OAI) System Manual ND-70922 (E)
  • Page 5: Table Of Contents

    NEAX2000 IVS OAI System Manual TABLE OF CONTENTS Page LIST OF FIGURES ............LIST OF TABLES .
  • Page 6 TABLE OF CONTENTS Page CHAPTER 3 SYSTEM DATA PROGRAMMING ....... . HOW TO READ THIS CHAPTER.
  • Page 7: List Of Figures

    LIST OF FIGURES Figure Title Page Figure 1-1 System Outline of OAI with RS-232C ........Figure 1-2 External Processor Connection for RS-232C Interface .
  • Page 8 LIST OF TABLES Table Title Page Table 1-1 RS-232C Interface Specification ......... Table 1-2 MODEM Specification .
  • Page 9: Introduction

    INTRODUCTION Purpose INTRODUCTION PURPOSE This manual explains the system description, installation procedure, programming procedure and troubleshooting information for providing the Open Application Interface (OAI) to the NEAX2000 IVS OUTLINE OF THIS MANUAL This manual contains the following chapters and appendix: CHAPTER 1 GENERAL INFORMATION This chapter explains the system outline and specifications of the OAI system.
  • Page 10: Reference Manuals

    INTRODUCTION Reference Manuals REFERENCE MANUALS Refer to the following manuals during installation: Installation Procedure Manual: Describes the installation procedure of the PBX system. Command Manual: Describes Customer Administration Terminal (CAT) operation, command function and setting data required for programming the system, and Resident System Program. Office Data Programming Manual: Contains the Customer Specification Sheet and Office Data Programming Sheet.
  • Page 11: Chapter 1 General Information

    CHAPTER 1 GENERAL INFORMATION This chapter explains the OAI system outline and specifications. NEAX2000 IVS OAI System Manual Page 3 ND-70922 (E), Issue 1.0...
  • Page 12: System Outline

    CHAPTER 1 GENERAL INFORMATION System Outline SYSTEM OUTLINE The PBX is equipped with an interface to provide user applications through an external processor. The interface supports RS-232C (Free Wheel) protocol and TCP/IP protocol. OAI with RS-232C For adding the interface with RS-232C, the AP01 card (OAI Interface Card) is required. Figure shows the system outline of OAI with RS-232C.
  • Page 13: Figure 1-2 External Processor Connection For Rs-232C Interface

    CHAPTER 1 GENERAL INFORMATION System Outline Figure 1-2 External Processor Connection for RS-232C Interface (1) External Processor Direct Connection EXTERNAL PROCESSOR AP01 (RS-232C) RS RVS-4(S) CA-A/RS RVS-4(S) CA-C (4 m/13.1 ft.) RS RVS-15(S) CA-A (15 m/49 ft.) Page 6 (2) External Processor Connection via MODEM EXTERNAL PROCESSOR AP01...
  • Page 14: Rs Rvs-15 Ca-A/Rs Rvs-15S Ca-A

    CHAPTER 1 GENERAL INFORMATION System Outline RS RVS-15 CA-A/RS RVS-15S CA-A RS RVS-4 CA-A/RS RVS-4 CA-C RS RVS-4S CA-A/RS RVS-4S CA-C NOTE: If the external processor does not send DTR or RTS signal, cut the signal lead marked by X in the D-Sub connector (external processor side) as shown in the wiring diagram below.
  • Page 15: Rs Norm-4 Ca-A/Rs Norm-4S Ca-A

    CHAPTER 1 GENERAL INFORMATION System Outline APPENDIX DEFINITION OF V.24 SIGNAL LEADS. Page 79 RS NORM-4 CA-A/RS NORM-4S CA-A (4 m/13 ft.) 06D-TXC (1) 24-TXC (2) 06B-RXC 17-RXC 06A-TXC (2) 15-TXC (1) 20-DSR 05C-DTR 05B-GND 01-GND 05A-TXD 02-RXD 04B-RXD 03-TXD 04A-RTS 04-DCD 05-CTS...
  • Page 16: Oai With Tcp/Ip-Ethernet

    CHAPTER 1 GENERAL INFORMATION System Outline OAI with TCP/IP-Ethernet The PBX is equipped with an interface to transmit/receive the control signals between the PBX and the Ethernet. The interface supports TCP/IP protocol. For adding the interface with TCP/IP, the ETHER card (CC01) (Ethernet Gateway Controller) is required in addition to the AP01 card. Figure 1-3 shows the system outline of OAI with TCP/IP-Ethernet.
  • Page 17: System Specifications

    CHAPTER 1 GENERAL INFORMATION System Specifications SYSTEM SPECIFICATIONS RS-232C Interface Specification Table 1-1 RS-232C Interface Specification DESCRIPTION SPECIFICATION REMARKS Transmission Speed 150, 300, 600, 1200, 2400, 4800 or 9600 bps Synchronization Asynchronous Transmission Mode Full Duplex Parity No Parity Stop Bit 1-Stop Bit Kind of Code JIS (8-bit)
  • Page 18 CHAPTER 2 INSTALLATION This chapter explains the hardware installation procedure to provide OAI interface to the PBX. NEAX2000 IVS OAI System Manual Page 11 ND-70922 (E), Issue 1.0...
  • Page 19: Chapter 2 Installation

    CHAPTER 2 INSTALLATION Precautions PRECAUTIONS Static Electricity Guard You must wear a grounded wrist strap to protect circuit cards from static electricity. Figure 2-1 Static Electricity Guard (1 of 2) • WHEN PLUGGING/UNPLUGGING A CIRCUIT CARD FRAME GROUND SCREW WRIST STRAP •...
  • Page 20: Precautions

    CHAPTER 2 INSTALLATION Precautions Figure 2-1 Static Electricity Guard (2 of 2) • WHEN MAKING A SWITCH SETTING ON A CIRCUIT CARD CIRCUIT CARD WEAR A WRIST STRAP AND PERFORM THE WORK ON A GROUNDED CONDUCTIVE WORK SURFACE. • WHEN CARRYING A CIRCUIT CARD CONDUCTIVE CIRCUIT POLYETHYLENE...

Table of Contents