Download
Share
Print this page
  1. Manuals
  2. Brands
  3. SENDER RAMPS Manuals
  4. Bicycle Accessories
  5. CORE 200
  6. Manual

SENDER RAMPS CORE 200 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
SENDER CORE RAMPS
CORE 200 STRAIGHT AND CURVED
FOOTWEAR:
VICE - BIKE:
STRIVE
PLEASE TAKE CARE OPENING YOUR PROGRESSION RAMPS WITH A KNIFE
THE OPTIONAL CARRY BAG MAY BE INSIDE ALONG WITH ASSEMBLY COMPONENTS.
Thank you for buying a SENDER CORE RANGE RAMP. They are part of our extensive, compact and transportable modular system.
Each part has been carefully considered for weight and strength. They are durable and built to last. Core Ramps are fixed in
height and angle. You can grow your range to progress and build confidence on Straight and Curved Transitions. Happy Landings.
MODULAR:
Our ramps integrate with other SENDER BOLT ON features. For advice on compatibility please contact us. Core ramps can be
used as a take-off and landing ramps in Straight or Curved mode.

Advertisement

loading
Need help?

Need help?

Do you have a question about the CORE 200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SENDER RAMPS CORE 200

Summary of Contents for SENDER RAMPS CORE 200

  • Page 1 SENDER CORE RAMPS CORE 200 STRAIGHT AND CURVED FOOTWEAR: VICE - BIKE: STRIVE PLEASE TAKE CARE OPENING YOUR PROGRESSION RAMPS WITH A KNIFE THE OPTIONAL CARRY BAG MAY BE INSIDE ALONG WITH ASSEMBLY COMPONENTS. Thank you for buying a SENDER CORE RANGE RAMP. They are part of our extensive, compact and transportable modular system.

  • Page 2: Safe Operation

    WEIGHT 12 Kgs CORE RANGE 200 mm HIGH – Fixed at 200 mm HIGH with 15 mm Terrain Adjustment Transition Length CORE 200 STRAIGHT and CURVED Ramps is 900 mm OPTIONAL COMPONENTS: TRANSPORT BAG – SKATE PLATE – PROGRESSION BOOSTER EXTENSION The SENDER EXTEDER must NEVER be used on the 200 CORE STRAIGHT and CURVED as it will tip over.

  • Page 3: Maintenance

    The Ramps have an OPTIONAL and strong Vinyl Carry Bag which has webbing strap points on the front you can use for attaching clothing (you will need to add elastic or similar). Lift the bag using the central lifting loop or both handles to mount on your back. The load / weight on one strap alone may rip the stitching.

  • Page 4: Very Important

    A Torque Wrench will ensure that ALL bolts are set at the max tension of 12 Nm Your ramp may come unassembled or assembled. Please reads the section appropriate to your purchase. CORE 200 STRAIGHT AND CURVED RAMP ASSEMBLY REFRESH KIT : A Refresh KIT will be available in our shop for components in contact with the ground subject to the most wear and tear.

  • Page 5: Assembly Tools

    24 x Stainless Steel Hinge Screws 18 x T Nuts 36 x Stainless Steel T Nut Screws ASSEMBLING YOUR CORE 200 CURVED OR STRAIGHT RAMP STAGE 1: Time to assemble approximately 1 – 1.5 Hrs Select all the components with 13 mm holes through the plywood. Lie them on a flat surface so you can see ALL of the CIRCLE / ROUND Markers around the holes.
  • Page 6 STAGE 2: Take the two FRONT Side Panels R + L and Cross Batons B1 + B2 + H. Place B1 in the VERTICAL Small Pocket at the front of the structure. Place B2 in the bigger Rear Vertical Pocket. IMPORTANT – H has 3 screw marker points. These must face UP! WARNING! YOU MUST DRILL EACH HOLE BEFORE FIXING COMPONENTS WITH A SCREW.
  • Page 7 Take Component H and push / place this between the Lower Sides of the ramp where there is Horizontal marker lines. IF H is a little loose then completely tighten the two protruding screws in B1 (described above). A clamp can also help to hold component H in place while you check the top and ends are flush.
  • Page 8 JOINING BLOCKS CAN BE USED TO HELP PREVENT THE STRUCTURE TIPPING WHILE YOU FIX THE COMPONENTS TOGETHER – COMPONENTS 200 L AND R CAN BE USED AS SPACER BLOCKS (AS DESCRIBED BELOW) TO HELP ALIGN THE SIDES AND SURFACES FAILURE TO COMPLETE THIS PROCESS ACCURATELY MAY PREVENT THE RAMP FROM FUNCTIONING PROPERLY AND MISSALIGN THE SURFACES WHEN BOLTED TOGETHER! YOU MUST start at the end with the VERTICAL SIDES as these connect with the other part of the ramp.
  • Page 9 Remove the clamps and then drill and fix at all remaining marker points. There are 4 more. 2 above the hinges and 2 in the centre of the arrow. Turn the entire Structure over. You will see the 3 marker holes in Baton H. Place one of the 4 x 30 Stainless Steel Screws beside the drill bit and use a piece of tape to mark HOLE DEPTH.
  • Page 10 STAGE 6: Take both Rear Legs and Side Panels now hinged together along with the Back Plate and another B baton. Place B into the vertical pocket on the side panels. Take the BACK Plate and rotate this so the text is facing out and is upside down. Use two clamps as shown to hold the structure together.
  • Page 11 USE THE JOINING BLOCKS AS SPACER BLOCKS Once you are satisfied that the BALANCE is correct clamp the surface. You must also check that the end of the surface and the End of the Vertical Side Panel is TOTALLY flush. Re-adjust if necessary and Re-clamp. Drill VERTICALLY through the marker point on the surface and secure with a TX25 Screws.
  • Page 12 Turn the ramp over and fit the second joining plate to the ramp sides with 4 x M10 x 35 Countersink Bolts and wind until FINGER TIGHT ONLY! PLEASE NOTE THAT THE SIDES OF A CORE 200 CURVED RAMP ARE OPEN ANGLED...
  • Page 13 200 CORE STRAIGHT JOIN CLOSED – 200 CORE CURVED RAMP OPEN Turn the ramp over so the surfaces are facing up. Press firmly / manipulate the surfaces at the join so the ramp is STRAIGHT or CURVED depending which model you have purchased. The Edge of the Surface at the join should be flush / touching! The Join between the side panels should be closed on the straight ramp and slight open on the curved ramp.
  • Page 14 A REFRESH KIT is available to REPLACE and RENEW components in contact with the ground once they wear out. Go around ALL the ramp bolts checking that they are tight before starting a JUMP SESSION. You are now ready to TAKE OFF or LAND using the CORE 200 STRAIGHT or CURVED RAMP. STORAGE AND TRANSPORT MODES Your ramp has two storage modes.
  • Page 15 COMPACT MODE CORE 200 RAMP Super Compact Mode: Remove the FRONT LEGS / BLOCKS. Remove the Rear Curved Legs. Undo and Remove the joining blocks. Fold the Ramp Surface. You now have a very compact stack of components. Ensure you store the bolts in a safe place. You may wish to strap the sections together OR better place in our (optional) transport bag.
  • Page 16 You can get expert advice at Sender. Do not hesitate to contact us. You can also order replacement parts. This keep your purchase environmentally friendly and keeps you rolling. Please subscribe to our YouTube Channel Sender Ramps for notifications when we upload new films. If you need advice or help please contact us direct support@sender-ramps.com...