Innovative NV9 Operation Manual
  1. Manuals
  2. Brands
  3. Innovative Manuals
  4. Bank Note Validator
  5. NV9
  6. Operation manual

Innovative NV9 Operation Manual

Innovative nv9 bank note validator: user guide
Hide thumbs Also See for NV9:
Table of Contents

Advertisement

Quick Links

NV9
OPERATIONS
MANUAL
INTELLIGENCE IN VALIDAT
Copyright Innovative Technology Ltd 2008
GA326-6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NV9 and is the answer not in the manual?

Questions and answers

Related Manuals for Innovative NV9

Summary of Contents for Innovative NV9

  • Page 1 OPERATIONS MANUAL INTELLIGENCE IN VALIDAT Copyright Innovative Technology Ltd 2008 GA326-6...

  • Page 2: Table Of Contents

    Appendix Appendix A – Drawings Appendix B – Escrow control Appendix C – Interface tools DA1 – DA2 Appendix D – Bezels Appendix E – Cash boxes Appendix F – PC system specification Index Copyright Innovative Technology Ltd 2008 GA326-6...

  • Page 3: Introduction

    NV9 Operations Manual 1 INTRODUCTION This manual describes the operation of the NV9 Bank Note Validator as fitted with Firmware Version 3.15 or greater. AUTIONS: • THIS PRODUCT MUST BE FITTED WITH A 2 AMP • THE NV9 VALIDATOR IS PIN FOR PIN COMPATIBLE WITH NV7/8/10 BUT NOT PIN FOR PIN COMPATIBLE WITH THE NV2/3/4/4X OR 5 SERIES PRODUCTS.
  • Page 4 NV9 Operations Manual GROUP EMAIL CONTACT BRAZIL suporte@bellis-technology.com.br CHINA support@innovative-technology.co.uk COLUMBIA support@automated-transactions.net GERMANY support@automated-transactions.de ENGLAND support@innovative-technology.co.uk SPAIN soporte@automated-transactions.es UNITED STATES OF AMERICA supportusa@bellis-technology.com REST OF THE WORLD sales@innovative-technology.co.uk Copyright Innovative Technology Ltd 2008 GA326-6...

  • Page 5: Environment And Power Requirements

    Humidity Table 1 – Environmental Requirements CAUTIONS: IF THE INPUT VOLTAGE FALLS BELOW +11V, THE NV9 MAY NOT OPERATE CORRECTLY (THE VALIDATOR WILL REJECT NOTES). THE AMBER STATUS LED AND FRONT BEZEL LIGHTS WILL FLASH TO INDICATE INCORRECT CONDITIONS. IT IS ESSENTIAL THAT THE POWER SUPPLY USED CAN SUPPLY AT LEAST 1.5 AMPS.

  • Page 6: General Description

    Connector Bezel Locking he NV9 Validator leaves the factory containing at least one currency data set so that it is ready for immediate installation. If it is desired to change the currency data set this may be done using either the PC based Currency Management software or the DA3 Validator Programming System.

  • Page 7: Nv9 User Interface

    Figure 2 - User Display and DIPswitch Settings Copyright Innovative Technology Ltd 2008 9 is shown below (see figure 2). It is simply a set of four REEN LED and an AMBER LED mounted on the top of the NV9. AMBER ON DIP...

  • Page 8: Dipswitch Settings

    Special Modes The special interface depends on the firmware that is used in the NV9, the firmware shipped as standard is ccTalk (un less specified by order). The table below shows all the options that can be downloa...

  • Page 9: Interface: Hardware Description

    5 INTE RFACES: HARDWARE DESCRIPTION The NV9 interface connector is located on the left sid refer to Table 3 for the pin allocation. Two are used f ere are five outputs and five inputs, the remaining four pins are reserved for factory use and should not be connected.

  • Page 10: Input And Output Hardware Circuits

    Inhibit channel 1 by holding this pin HIGH. To Enable a channel Inhibit 1 the inhibit must b Inhibit 2 Inhibit 3 Inhibit 4 Busy NV9 is validating and stacking output. Active low while the NV9 Escrow Factory Use Only Factory Use Only Factory...

  • Page 11: Table 6 - Interface Logic Levels

    AUTION: THE SERIAL INTERFACES WILL ONLY WORK IF THE RELEVANT INTERFACE OFTWARE IS CORRECTLY INSTALLED. Name Validator TxD Validator RxD Table 7 - Serial Interface Inputs and Outputs Copyright Innovative Technology Ltd 2008 Logic low Logic high 0V to +0.5V +3.7 V +12V 0.6V...

  • Page 12: Machine Interfaces: Protocols

    Vend line is set low for a period of 100 ± 3ms. Pulses outside these limits should be rejected as a precaution against false triggering. Busy Output: (Pin 9). This is a general-purpose busy signal. It is active low while the NV9 is in operation.

  • Page 13: Binary Output - Bin

    If the NV9 is set to binary mode it will issue the vend signals as a binary pattern on the pa outputs for 100 ± 3ms. In this way a maximum of 15 otes individually inhibited.

  • Page 14: Serial Input/Output - Sio (Baud Rate Is Defaulted To 300)

    30 second time-out. Setting all the inhibits high causes a note reject. the event of a note being forcibly removed from the mouth of the NV9 during the 30- second interval, the NV9 will go out of service for 45 seconds.

  • Page 15: Nv200 Operations Manual

    The NV9 will operate at 9600 Baud rate if Inhibit 2 line is held low when powered • The NV9 will not be enabled in serial I/O mode if Inhibit 3 line is held low when the unit is powered up. A software enable must be sent to enable the validator.

  • Page 16: Table 8 - Receive And Transmit Codes

    NV9 Operations Manual The NV9 will receive and transmit the following event codes. Recognised Receive Codes to NV9 MESSAGE Inhibit C1 Inhibit C2 Inhibit C3 Inhibit C4 Inhibit C5 Inhibit C6 Inhibit C7 Inhibit C8 Inhibit C9 Inhibit C10 Inhibit C11...

  • Page 17: Serial Input/Output - Si2 (Baud Rate Is Defaulted To 9600)

    Inhibit 2 has no function. • All Transmit and Receive codes an Chapter 6.4 (See tables 8 The data is formatted as follows: 1-start bit, Copyright Innovative Technology Ltd 2008 Validator Decimal Value Validator Busy Validator Ready Accept on channel 2...

  • Page 18: Smiley ® Secure Protocol (Ssp)

    RS232 (TTL) - open collector driver • igh Speed 9600 Baud Rate • 16 bit CRC error checking • Data Transfer Mode Copyright Innovative Technology Ltd 2008 Bit 2 Bit 3 Bit 4 Bit 5 te no recog ized Secure Protocol (SSP) Specification (ITL Drawin ®...

  • Page 19: Multi-Drop Bus/Internal Communications Protocol (Mdb/Icp)

    MDB option of the interface firmware loaded into the NV9. (DIPswitch 2 enables a fast reset on power up). e Fast Reset option should be set if the NV9 continuously resets the stacker after the machine is powered on. The Fast Reset option can be enabled via the Validator Manager Software, or by setting Dipswitch 2 to the ON position.

  • Page 20: Cctalk Protocol - Cct

    NV9 Operations Manual The NV9 banknote Validators have a unique address – 00110XXX binary (30H). The VMC polls the bus to detect presence of the NV9 Validators or get information on the current status of the Validators. The Validators will respond when asked for activity with an acknowledgment, a negative acknowledgment or a specific reply, depending on its current status.

  • Page 21: Non-Isolated Serial Protocol (Nis)

    N (DIPswitch 2 is not functional in this mode). There is a single output DATA line from the NV9. There are three control lines, two from the controller ‘’ACCEPT ENABLE’’ and ‘’SEND’’ and one from the Vali (INTERRUPT) (see table 10).

  • Page 22: Validator Programming System (Da3)

    Red Locking A rm Figure 9 - Bezel and Validator Removal 8.2 CASH BOX OPTIONS The NV9 validators can be supplied with various cash box options, shown in Appendix E. Slide In Cash Box Clip On Cash Box Figure 10 - Clip On and Slide in Cash Boxes...

  • Page 23: Routine Maintenance

    9 ROUTINE MAINTENANCE The NV9 Validator has been designed to mini Much of this is achieved by careful hardware and software desig upon the environment the NV9 may at some time requ path clearing. 9.1 CLEANING CAUTION: DO NOT USE SOLVENT BASED CLEANERS...

  • Page 24: Figure 11 - Nv9 Sensors

    5. Repeat steps 3 and 4 until all dust and debris has been removed from both belts. 6. Repeat step 3 using a DR Copyright Innovative Technology Ltd 2008 Optical Sensor Figure 11 - NV9 Sensors ampened with water containing a mild d Y lint free cloth to remove any excess moisture. Insert Paper...

  • Page 25: Note Path Debris Clearing / Belt Changing

    Release Catch Note S tacker sher Plate ote Path Figure 12 - NV9 Note Path and Lozenge Access Debris Clearing Examine the note paths, lozenge and no Carefully clear an d wipe the surfaces of the note paths and lozeng...

  • Page 26: Fault Finding Analysis

    Validator rejects Is the required note genuine notes contained in the Currency file? Are sensors ok Copyright Innovative Technology Ltd 2008 SOLUTION Check the Power Supply specification Check the LED Status codes (Chapter 4.2). Check correct interf programmed in using VALIDATOR MANAGER software.

  • Page 27: Support Tools

    11.3 INTERNET WEBSITE SUPPORT The Innovative Technology Ltd website provides the means to download new and updated currency sets and new versions of firmware for the NV9. You can obtain these along wi technical bulletins by visiting www.innovative-technology.co.uk 11.4 E-MAIL SUPPORT...

  • Page 28: Appendix

    NV9 Operations Manual A PPENDIX APPENDIX A - DRAWINGS Copyright Innovative Technology Ltd 2008 GA326-6...
  • Page 29 Copyright Innovative Technology Ltd 2008 GA326-6...
  • Page 30 Copyright Innovative Technology Ltd 2008 GA326-6...
  • Page 31 Copyright Innovative Technology Ltd 2008 GA326-6...
  • Page 32 Copyright Innovative Technology Ltd 2008 GA326-6...
  • Page 33 Copyright Innovative Technology Ltd 2008 GA326-6...

  • Page 34: Appendix B - Escrow Control

    NV9 Operations Manual APPENDIX B – ESCROW FUNCTION The NV9 has a single note escrow facility (pin 10) used in Parallel, Pulse and Binary modes. This allows the Validator to hold onto the note once accepted, and then only stack the note in the cash box when the host machine confirms that the Vend operation has been completed.

  • Page 35: Appendix C - Interface Tools Da1 - Da2

    NOTE: The Validator must be in SSP mode when connected to a computer and then returned to the Original Settings when the download is complete. PC Serial Port Figure 14 - Connecting DA1 to a NV9 and PC for upgrading Copyright Innovative Technology Ltd 2008 DA2 adapter board...

  • Page 36: Figure 15 - Connecting Da2 To A Nv9 And Pc For Upgrading Software

    Opera ing S stem OTE: All files contained on the CD are available from the ITL website: www.innovative-technolog y.co.uk Please contact support@innovative-technology.co.uk, if you require further assistance Copyright Innovative Technology Ltd 2008 rt of the PC. Once the connections have DA2 Adapter Board +12V DC automatically run and an installation menu will appear.

  • Page 37: Appendix D - Bezels

    APPENDIX D – NV9 BEZELS PA189 P 268 Horizontal Bezel Assembly 69mm Fixed Width Horizontal Bezel PA19 tical Down Sta nded Snout Bezel A PA324 PA190 PA256 PA323 Vertical Up/Down Extended 66mm Vertical Up Stack Extended Vertical Up/Down Flat 69mm...

  • Page 38: Appendix E - Cash Boxes

    APPENDIX E – NV9 CASH BOXES PA185 PA186 Clip on Cash Box Assembly (300C) PA192 Locking C ash Box Assembl y (30 Slide on Cash Box Assembly (300S) PA193 PA194 Clip on Cash Box Assembly (600C) Slide on Cash Box Assembly (600S)

  • Page 39: Appendix F - Pc System Specification

    NV9 Operations Manual APPENDIX F – PC SYSTEM SPECIFICATION The ITL Validator Software has been te sted and verified using Windows 2000/XP on a Pentium based PC System ( Microsoft and Intel). Full functionality cannot be © guaranteed on lower specification systems.

  • Page 40: Index

    Figure 6 – Typical Serial Output: Transmission of the value 20 (decimal), Note not recognized Figure 7 – MDB Opto Isolated Input / Output circuits NV9 MDB Slave Figure 8 – ccTalk connector pins on the NV9 Figure 9 – Bezel and validator removal Figure 10 –...
  • Page 41 Pending protecting this product. If you require further details please contact the factory. Innovative Technology is not responsible for any loss, harm, or damage caused by the installation and use of this product. This does not affect your local statutory rights. If in doubt please contact Innovative Technology for details of any changes.

Table of Contents