Related Manuals for Innovative NV200
Summary of Contents for Innovative NV200
- Page 1 NV200 OPERATIONS MANUAL INTELLIGENCE IN VALIDAT Copyright Innovative Technology Ltd 2008 GA620-1...
-
Page 2: Table Of Contents
Maintenance and re-initialisation Routine maintenance Re-initialisation Appendix Appendix A – How to order a NV200 validator Appendix B – NV200 mechanical installation Appendix C – Escrow function Appendix D – Implemented ccTalk Appendix E – Parts list and exploded drawings... -
Page 3: Introduction
NV200 Operations Manual 1 INTRODUCTION This manual describes the operation of the NV200 Bank Note Validator, programmed with Firmware Version 4.04 or greater. This document is intended for those who will: • Install the NV200 equipment. • Maintain the NV200 equipment... - Page 4 NV200 Operations Manual GROUP EMAIL CONTACT BRAZIL suporte@bellis-technology.com.br CHINA support@innovative-technology.co.uk COLUMBIA support@automated-transactions.net GERMANY support@automated-transactions.de ENGLAND support@innovative-technology.co.uk SPAIN soporte@automated-transactions.es UNITED STATES OF AMERICA supportusa@bellis-technology.com REST OF THE WORLD sales@innovative-technology.co.uk Copyright Innovative Technology Ltd 2008 GA620-1...
-
Page 5: Environment And Power Requirements
Outputs with 2K2Ω pull up Maximum Current Sink It is recommended that a ferrite cable clamp be used on the cable to the NV200, with the cable having a single turn around the ferrite. The suggested ferrite is as follows... -
Page 6: General Description
Interface ACCESSING Head unit removal In the Appendix B – NV200 Mechanical Installation you can find a detailed explanation for cash box removal, note path access, bezel installation and validator head unit removal. Copyright Innovative Technology Ltd 2008 Figure 1 - The NV200 validator Width: 60 –... -
Page 7: Figure2 - Order Code Example
The length of the screw must be no more than 6mm plus the thickness of the mounting bracket. It is also possible to mount the NV200 via fixing holes in the rear of the chassis. Care must be taken not to obstruct the cash box when using the rear fixing holes. We do not recommend mounting from the base unless the NV200 is also supported from the back. -
Page 8: Machine Interfaces
Card Utilities software will also set the colour and operation of the LED’s. 4.1.2 DIAGNOSTIC CODES If the NV200 detects an error that is preventing normal operation, the Bezel LED’s will indicate the cause of the problem by flashing in a certain sequence as shown in Table 5 - Bezel LED Diagnostic Codes. -
Page 9: Hardware
Table 6 – 16 way External Connector Pin Out It is recommended that a ferrite cable clamp be used on the cable to the NV200, with the cable having a single turn around the ferrite. See chapter 2 Environment and Power Requirements for more details on the suggested ferrite. -
Page 10: Usb Connection
NOTE: This mode can only be cancelled by re-programming via the Bank Note Validator Currency Manager software. Please ensure you are aware of all the NV200 programmed settings before entering this mode. Failure to restore the original setting will stop the NV200 from operating in the host machine... -
Page 11: Cctalk
3-wire bus (+12V, 0V and Data). To use the NV200 in ccTalk mode, pins 1 and 5 (Tx and Rx) must be connected together as the data line. -
Page 12: Mdb (Multi Drop Bus)
A Vending Machine Controller (VMC) has the capability of communicating with 32 peripherals or slaves. Connections: To use the NV200 in MDB mode, an IF5 external interface is required. The IF5 regulates the power supply and opto-isolates the communication lines. Figure 5 - Connecting the NV200 in MDB mode... -
Page 13: Parallel
NV200 Operations Manual 4.3.4 PARALLEL In parallel mode the NV200 will issue a 100ms (±3%) active LOW pulse on the relevant vend line. A maximum of 4 channels can be used. Connections Name Type Vend 1 Output Vend 2 Output... -
Page 14: Pulse
NV200 Operations Manual 4.3.5 PULSE In Pulse mode the NV200 outputs a number of pulses on Vend 1. The number of pulses for each channel is different and set to default values within the dataset. The number of pulses and the pulse duration can be modified using the Bank Note Validator Currency Manager Software. -
Page 15: Binary
NV200 Operations Manual 4.3.6 BINARY In Binary mode, the NV200 will issue a binary pattern on vend lines 1 to 4 as shown in Table 12 – Binary credit outputs. A maximum of 15 channels can be used. Vend Vend... -
Page 16: Reprogramming The Nv200
Bank Note Validator Currency Manager Software 6.1 DATAFLASH® MEMORY CARDS The slot at the front of the NV200 can be used to reprogram the validator from an Atmel DataFlash® Memory card, without the need to remove the validator from the host machine. -
Page 17: Bank Note Validator Currency Manager Software
• Use diagnostic functions to check Validators operation When connected to a computer, the NV200 must be set to SSP mode. SSP programming mode is activated temporarily for the purpose of re-programming the NV200. This is done by switching DIP Switch 8 ON then OFF again. -
Page 18: Maintenance And Re-Initialisation
The NV200 has an in-built self-calibration system that maintains the optical sensors at their best operating point. However if the NV200 is disassembled for any reason it will need to be re-initialised. Re-initialisation may only be performed under license from ITL, contact support@innovative-technology.co.uk for further details. -
Page 19: Appendix
LED Brightness – The values of brightness for each colour of the bezel LED’s in the order Red, Green, Blue between 0 and 255. If no colour is specified, the NV200 will be shipped with the bezel colour set to magenta by default. - Page 20 PIN programmed into the NV200 for re-programming to take place. Number of Re-tries – The number of times the NV200 will read the note should it not be recognised on the first attempt. This value must be between 0 and 2 ccTalk Encryption Key –...
- Page 21 Card PIN Number of re-tries CcTalk key APPROVED Customer: Copyright Innovative Technology Ltd 2008 Innovative Technology Ltd Derker Street – Oldham – England - OL1 4EQ Tel: +44 161 626 9999 Fax: +44 161 620 2090 E-mail: support@innovative-technology.co.uk Web site: www.innovative-technology.co.uk...
-
Page 22: Appendix B - Nv200 Mechanical Installation
7.2 APPENDIX B – NV200 MECHANICAL INSTALLATION Drawing Number GA604 In line with continued product development Innovative Technology Ltd reserves the right to change specifications without prior notice. ACCEPTS NOTES: 1. 60 mm x 85 mm WIDE 2. 115 mm x 170 mm LONG SUPPLY AND POWER CONSUMPTION: VOLTAGE: 11.00 - 13.5 V... - Page 23 NV200 VALIDATOR LOCK FITTING 1. UNSCREW 2 OFF SCREWS (INDICATED) WITH A T8 TORX SCREWDRIVER 2. WITHDRAW LOCK BRACKET FROM THE VALIDATOR HEAD 3. UNCLIP LOCK BLANKING PLUG AND LOCK CAM GEAR (RETAIN) 4. INSERT LOCK INTO BRACKET (AS SHOWN), AND FIX IN PLACE WITH LOCK RETAINING NUT 5.
- Page 24 NV200 CASHBOX LOCK FITTINGS 1. OPEN CASHBOX DOOR 2. UNCLIP LOCK CAMS FROM BLANKING PLUGS. (RETAIN) 3. UNCLIP THE TWO BLANKING PLUGS FROM CASHBOX DOOR. 4. FIT THE TWO LOCK BODEIS INTO RECESSES IN THE DOOR IN THE ALIGNMENT SHOWN...
-
Page 25: Figure 7 - Cashbox Removal
To close the note path, simply push the cover down until it clicks into place BEZEL INSTALLATION To fit the bezel to the NV200 access to the note path is required. Lift the upper cover by pulling the latch forward. Connect the cable... -
Page 26: Appendix C - Escrow Function
8.3 APPENDIX C – ESCROW FUNCTION The NV200 has a single note escrow facility (pin 10) used in Parallel, Pulse and Binary modes. This allows the Validator to hold onto the note once accepted, and then only stack the note in the cash box when the host machine confirms that the Vend operation has been completed. - Page 27 30 second time-out. For channels above 4, setting all the inhibits high will cause a note reject. In the event of a note being forcibly removed from the mouth of the NV200 during the 30-second interval, the NV200 will go out of service for 45 seconds.
-
Page 28: Appendix D - Implemented Cctalk ® Commands
REQUEST_DATA_STORAGE_AVAIL REQUEST_OPTION_FLAGS CALCULATE_ROM_CHECKSUM REQUEST_BUILD_CODE REQUEST_BASE_YEAR REQUEST_ADDRESS_MODE READ_BUFFERED_BILL_EV REQUEST_BILL_ID REQUEST_COUNTRY_SCALING REQUEST_BILL_POSITION MODIFY_BILL_OPERATING_MODE REQUEST_BILL_OPERATING_MODE STACKER_CYCLE OPERATE_BI_MOTORS REQUEST_CURRENCY_REVISION SWITCH_ENCRYPTION_CODE STORE_ENCRYPTION_CODE READ_BARCODE_DATA REQUEST_COMMS_REVISION Table 13 – Implemented ccTalk Commands Copyright Innovative Technology Ltd 2008 COMMANDS ® Command SIMPLE_POLL SET_INHIBITS REQ_INHIBITS ROUTE_BILL RESET_DEVICE Header GA620-1... -
Page 29: Appendix E - Parts List And Exploded Drawings
8.5 APPENDIX E – PARTS LIST AND EXPLODED DRAWINGS The Following Assemblies are available as spares Part Number PA610 PA621 PA629 PA630 PM614 MC247 Copyright Innovative Technology Ltd 2008 Description Where Used Bezel assy PA631 Validator final assy PA631 Cashbox final assy PA631... - Page 30 NV200 VALIDATOR FULL ASSEMBLY Drawing Number PA631 1. OPEN THE LID OF VALIDATOR ASSEMBLY (PA621) BY FIRST SLIDING FORWARD THE HANDLE ON TOP, PLUG IN THE CABLE OF BEZEL ASSEMBLY (PA610) THEN CLICK IT DOWN INTO PLACE, CLOSE LID. 2. ALIGNING THE LUGS, LOWER VALIDATOR ASSEMBLY (PA621) ONTO CHASSIS, SLIDE VALIDATOR ASSEMBLY BACKWARDS TO CLICK SECURELY INTO PLACE.
-
Page 31: Index
Figure 2 – Order Code Example Figure 3 – Connector and Switch Location Figure 4 – Pin detail Figure 5 – Connecting the NV200 in MDB mode Figure 6 – Order Code Example Figure 7 – Cashbox Removal Figure 8 – Note Path Access Figure 9 –... - Page 32 Pending protecting this product. If you require further details please contact the factory. Innovative Technology is not responsible for any loss, harm, or damage caused by the installation and use of this product. This does not affect your local statutory rights. If in doubt please contact Innovative Technology for details of any changes.
Need help?
Do you have a question about the NV200 and is the answer not in the manual?
Questions and answers