Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Chapters
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Innovative NV200
Summary of Contents for Innovative NV200
- Page 1 NV200 CONCISE MANUAL INTELLIGENCE IN VALIDAT Copyright Innovative Technology Ltd 2008 GA621-1...
-
Page 2: Table Of Contents
4.2.4 Dip switches Using barcodes Appendix Appendix A – How to order a NV200 validator Appendix B – NV200 mechanical installation Index The chapter numbers in this document are synchronized with the operations manual in order to help when searching for information. Therefore those chapter numbers that are not included in this manual will be skipped. -
Page 3: Introduction
NV200 Concise Manual 1 INTRODUCTION This manual describes the operation of the NV200 Bank Note Validator, programmed with Firmware Version 4.04 or greater. This document is intended for those who will maintain the NV200 equipment. To have full information about the configuration of this equipment please refer, via our website, to the NV200 Operations Manual GA620. - Page 4 NV200 Concise Manual GROUP EMAIL CONTACT BRAZIL suporte@bellis-technology.com.br CHINA support@innovative-technology.co.uk COLUMBIA support@automated-transactions.net GERMANY support@automated-transactions.de ENGLAND support@innovative-technology.co.uk SPAIN soporte@automated-transactions.es UNITED STATES OF AMERICA supportusa@bellis-technology.com REST OF THE WORLD sales@innovative-technology.co.uk Copyright Innovative Technology Ltd 2008 GA621-1...
-
Page 5: Environment And Power Requirements
Outputs with 2K2Ω pull up Maximum Current Sink It is recommended that a ferrite cable clamp be used on the cable to the NV200, with the cable having a single turn around the ferrite. The suggested ferrite is as follows... -
Page 6: General Description
Cash box capacity Interface CCESSING Head unit removal the Appendix B – NV200 Mechanical Installation you can find a detailed explanation for cash box removal, note path access, bezel installation and validator head unit removal. Copyright Innovative Technology Ltd 2008 el illumination Width: 60 –... -
Page 7: Figure2 - Order Code Example
The length of the screw must be no more than 6mm plus the thickness of the mounting bracket. It is also possible to mount the NV200 via fixing holes in the rear of the chassis. Care must be taken not to obstruct the cash box when using the rear fixing holes. - Page 8 NV200 Concise Manual REPROGRAMMING THE NV200 The NV200 can be updated in a number of ways as follows: · Atmel Dataflash Memory Cards · ITL Bank Note Validator Currency Manager Software Please refer to the Operations Manual for detail information about reprogramming.
-
Page 9: Machine Interfaces
Bezel LED’s can also be set to either permanently on or flashing at a rate of once per second when the note validator is enabled. e-programming the NV200 with a memory card that has been programmed using the NV Card Utilities software will also set the colour and operation of the LED’s. -
Page 10: Hardware
+5V via 10KΩ. nction changes depending on machine interfac protocol (see individual interface descriptions for details) Active LOW when the NV200 is transporting, reading or stacking a note Enable th e escrow function by holding LO Parallel, Pulse or Binary modes... -
Page 11: Usb Connection
Channel 1 Inhibit Channel 2 Inhibit Channel 3 Inhibit Channel 4 Inhibit Channel 5 Inhibit Channel 6 Inhibit Programming Mode Copyright Innovative Technology Ltd 2008 Switch OFF ( ) Barcode read Barcode read disabled enabled Channel 1 enabled Channel 2 enabled... -
Page 12: Using Barcodes
In SSP mode there is a set of commands to set the required barcode configuration. • In ccTalk mode, the default number of characters expected by the NV200 is 18. To change this value, the Bank Note Validator Currency Manager software must be used For more details on implementing barcodes into SSP or ccTalk applications, please see the relevant specification documentation. -
Page 13: Appendix
– The values of brightness reen, B lue between 0 and 255. If no colour is specified, the NV200 will be shipped with the bezel colour set to magenta by default. Bezel Flash – Y/N. If the bezel flash is set to Y, when enabled, the validator bezel will flash at a ate of 1Hz. - Page 14 PIN programmed into the NV200 for re-programming to take lace. Number of Re-tries – The number of times the NV200 will read the note should it not be recognised on the first attempt. This value must be between 0 and 2 cTalk Encryption Key –...
- Page 15 Card PIN Number of re-tries CcTalk key APPROVED Customer: Copyright Innovative Technology Ltd 2008 Innovative Technology Ltd Derker Street – Oldham – England - OL1 4EQ Tel: +44 161 626 9999 Fax: +44 161 620 2090 E-mail: support@innovative-technology.co.uk Web site: www.innovative-technology.co.uk...
-
Page 16: Appendix B - Nv200 Mechanical Installation
7.2 APPENDIX B – NV200 MECHANICAL INSTALLATION Drawing Number GA604 In line with continued product development Innovative Technology Ltd reserves the right to change specifications without prior notice. ACCEPTS NOTES: 1. 60 mm x 85 mm WIDE 2. 115 mm x 170 mm LONG... - Page 17 NV200 VALIDATOR LOCK FITTING 1. UNS CREW 2 OFF SCREWS (INDICAT D) WITH A T 8 TORX SCREWDRIVER 2. W ITHDRAW LOCK BRACKET FROM THE VALIDATOR 3. UNCLIP LOCK BLANKING PLUG AND LO CK CAM GEAR (RETAIN) 4. IN SERT LOCK INTO BRACKET (AS SHOW N), AND FIX IN PLACE WITH LOCK RETAINING NUT 5.
- Page 18 NV200 CASHBOX LOCK FITTINGS 1. OPEN CASHBOX DOOR 2. UNCLIP LOCK CAMS FROM BLANKING PLUGS. (RETAIN) 3. UNCLIP THE TWO BLANKING PLUGS FROM CASHBOX DOOR. 4. FIT THE TWO LOCK BODEIS INTO RECESSES IN THE DOOR IN THE ALIGNMENT SHOWN...
-
Page 19: Figure 7 - Cashbox Removal
To close the note path, simply push the cover down until it clicks into place BEZEL INSTALLATION To fit the bezel to the NV200 access to the note path is required. Lift the upper cover by pulling the latch forward. Connect the cable... -
Page 20: Figure 9 - Validator Head Removal
Head release latch securely into place Figure 9 – Validator head r oval Copyright Innovative Technology Ltd 2008 GA621-1... -
Page 21: Index
Table 6 – 16 way External Connector Pin Out Table 7 – Dip Switch Functions INDEX OF FIGURES Figure 1 – The NV200 Figure 2 – Order Code Example Figure 3 – Connector and Switch Location Figure 4 – Pin detail Figure 6 –... - Page 22 Pending protecting this product. If you require further details please contact the factory. Innovative Technology is not responsible for any loss, harm, or damage caused by the installation and use of this product. This does not affect your local statutory rights. If in doubt please contact Innovative Technology for details of any changes.
Need help?
Do you have a question about the NV200 and is the answer not in the manual?
Questions and answers