ECO2 Systems SANCO2 GS4-45HPC Installation Manual page 23

Block Out Time Setting
Block Out Time Setting
Enter into Commissioning Mode
First option is the Heat Setting
Enter into Commissioning Mode
Second option is Temperature Setting–
First option is the Heat Setting
Press the UP Key to access Block Out Time then Press Enter to access
Second option is Temperature Setting–
Block out time setting mode
Press the UP Key to access Block Out Time then Press Enter to access
This mode is used to set the block out time that prevents the heat pump unit
This mode is used to set the block out time that blocks the heat pump unit operation within
operation within the chosen time period.
This mode is used to set the block out time that prevents the heat pump unit
the setting time. Block out times are used if the customer has a time of use tariff.
operation within the chosen time period.
Block out times are used if the customer has a time of use tariff or wants to take
Change the mode
advantage of Solar PV production
Block out times are used if the customer has a time of use tariff or wants to take
Press and hold down Up and Down keys together in the clock display mode to go to
advantage of Solar PV production
the block out time setting mode. Once the mode is changed, 'bo' and '00XX' (00 =
'bo' and '00XX' (00 = Out Beginning time, XX = Out end time) are displayed. (Initial setting
start time, XX = end time) are displayed. (Initial setting = 00 o'clock for both start
= 00 o'clock for both start and end)
'bo' and '00XX' (00 = Out Beginning time, XX = Out end time) are displayed. (Initial setting
and end)
= 00 o'clock for both start and end)
Adjust set block out Beginning time
Adjust set block out start time
Press Up or Down key and '00' (start time) in '00XX' starts flashing and 'XX' (end
Adjust set block out Beginning time
Press Up or Down key and '00' (start time) in '00XX' starts flashing and 'XX' (end
time) illuminates. Now the block out Beginning time can be adjusted. Setting can
Press Up or Down key and '00' (start time) in '00XX' starts flashing and 'XX' (end
time) illuminates. Now the block out start time can be adjusted. Setting can be
be performed only in hour increments, not in minutes. Time is displayed in Military
time) illuminates. Now the block out Beginning time can be adjusted. Setting can
performed only in hour increments, not in minutes.
time not AM/PM
be performed only in hour increments, not in minutes. Time is displayed in Military
time not AM/PM
Set block out start time
Set block out Beginning time
Press the Enter key to set the desired time setting. After the start time is set, the
Press the Enter key to set the desired time setting. After the start time is set, the
Set block out Beginning time
start time display stops flashing. The end time display starts flashing at the same
start time display stops flashing. The end time display NOW starts flashing.
Press the Enter key to set the desired time setting. After the start time is set, the
time.
THIS TIME WILL THE TIME WHEN THE HEAT PUMP IS FIRST PREVENTED
start time display stops flashing. The end time display NOW starts flashing.
FROM OPERATING EVEN IF THE TANK IS COLD
THIS TIME WILL THE TIME WHEN THE HEAT PUMP IS FIRST PREVENTED
Adjust block out end time
FROM OPERATING EVEN IF THE TANK IS COLD
Set to the desired end time by using Up and Down keys. Setting can be performed
Adjust block out end time
only in hour increments, not in minutes.
Set to the desired end time by using Up and Down keys. Setting can be performed
Adjust block out end time
only in hour increments, not in minutes. Time is displayed in Military time not
Set to the desired end time by using Up and Down keys. Setting can be performed
Set block out end time
AM/PM
only in hour increments, not in minutes. Time is displayed in Military time not
Press enter key to adjust the desired time setting. After the end time is set, then it
AM/PM
starts to display 'bo' and '00XX' (00 = start time, XX = end time) by turns.
Set block out end time
Press enter key to set the desired time setting. After the end time is set, the start
Set block out end time
Go back to clock display mode
time and end time are displayed for two seconds, then it starts to display 'bo' and
Press enter key to set the desired time setting. After the end time is set, the start
Hold down Enter key to go back to the clock display mode. It will automatically go
'00XX' (00 = start time, XX = end time) sequentially.
time and end time are displayed for two seconds, then it starts to display 'bo' and
back to the clock display mode when no panel operation is performed for more
THIS TIME WILL THE TIME WHEN THE HEAT PUMP IS NOW ALLOWED TO
'00XX' (00 = start time, XX = end time) sequentially.
than 60 seconds. Block out time setting mode cannot be set unless the end time
OPERATE BASED ON TANK TEMPERATURE
THIS TIME WILL THE TIME WHEN THE HEAT PUMP IS NOW ALLOWED TO
setting is confirmed.
OPERATE BASED ON TANK TEMPERATURE
Go back to clock display mode
Cancel block out setting
Press Enter key to go back to the clock display mode. It will automatically go back
Go back to clock display mode
To cancel the block out setting, set both start and end times to the same time.
to the clock display mode when no panel operation is performed for more than 60
Press Enter key to go back to the clock display mode. It will automatically go back
seconds. Block out time setting mode cannot be set unless the end time setting is
to the clock display mode when no panel operation is performed for more than 60
※ ※ Example setting
confirmed.
seconds. Block out time setting mode cannot be set unless the end time setting is
Bo Setting For Example " 13 01 "
confirmed.
Cancel block out setting
To cancel the block out setting, set both beginning and end times to '00'. Setting to
Cancel block out setting
AM
other than '00' (01 ~ 23) will be interpreted as a setting error and the end time will
To cancel the block out setting, set both beginning and end times to '00'. Setting to
flash. Make sure to set both times to '00' when cancelling the block out time
○
other than '00' (01 ~ 23) will be interpreted as a setting error and the end time will
setting.
flash. Make sure to set both times to '00' when cancelling the block out time
setting.
-
PM
○
13
Unit will not Run
Sanden Heat Pump – Installation Manual
Page 21 of 40
Sanden Heat Pump – Installation Manual
SANCO Heat Pump – Installation Manual
Page 21 of 40
2
Page 23 of 44
AM
○
01