Related Manuals for Hussmann VGD
Summary of Contents for Hussmann VGD
- Page 1 Rev. 0505 VGM, VGD Vertical Glass Service Deli, Meat, Fish Case P/N VGM,VGD-0505 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
HUSSMANN CHINO PRODUCT CONTROL The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and replacement part purposes. All correspondence pertain- ing to warranty or parts ordering must include the serial number of each piece of equipment involved in order to provide the customer with the correct parts. -
Page 3: Important Information
The VGM / VGD service cases are easy to work, attrac- tive merchandising display cases capable of maintaining superb product quality, with the installation of the proper controlling devices. These should be set according to Hussmann’s specifications and combined with a properly maintained humidity system. -
Page 4: Installation
75°F and 55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows (etc.) to create air currents around the merchandiser, as this will impair its correct operation. Product temperature should always be maintained at a constant and proper temperature. - Page 5 Slide second case up to first case snugly. Then level second case to the first case so glass front, bumper and top are flush. To compress silicone at joint, use two Jurgenson wood clamps. Make sure case is level from front to back and side to side on inside bulkheads at joint.
-
Page 6: Plumbing
The P-trap must be installed to prevent air leakage and insect entrance into the fixture. NOTE: PVC-DWV solvent cement is recommended. Follow the Hussmann’s instructions. I N S T A L L I N G C O N D E N S A T E... -
Page 7: Humidification
225-01-2026 Humidification IMPORTANT INFORMATION The VGM / VGD case line is easy to work, and capable of maintaining superb product quality with the installation of the proper controlling devices. These should be set according to the Hussmann’s specifications, and a prop- erly maintained humidity system. -
Page 8: Refrigeration
VGM, VGD-0505 R E F R I G E R A N T T Y P E The standard refrigerant will be R-22 unless otherwise specified on the customer order. Check the serial plate on the case for information. REFRIGERATION LINES... -
Page 9: User Information
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. -
Page 10: Non-Glare Glass
CLEANING Hussmann recommends using a clean damp chamois, or a paper towel marked as dust and abrasive free with ® Plastic Cleaner and Polish available by calling Sumner Labs at 1-800-542-8656. -
Page 11: Maintenance
TOWARD THE MOTOR. COPPER COILS The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers. Hussmann recommends using #15 Sil-Fos for repairs. - Page 12 VGM, VGD-0505 Increase the height to 12", and raise and lower the glass 6 more times. Finally, raise the glass to it's full extension. This should release any settled lubricant in the cylinders, and prevent any stress on the front glass. (1)(3) G L A S S R E P L A C E M E N T &...
- Page 13 Glass Sweep Installation (WHERE APPLICABLE) PARTS LIST • Silicone 1200 (or comparable) • Masking tap (not supplied) INSTRUCTIONS Cut a strip of the glass sweep material to the proper length. Open glass wide enough to apply a few small drips of #1200 silicone down the edge of one side of the glass.
-
Page 14: Case Specifications
DISCHG. TYPE MODEL T-STAT/ LENGTH REQ’D EVAP PROD DISC VELOC CUT IN APP. @FPM SETTINGS EVAP. COIL VGD Deli (Blower Coil) Deli 20° 34° 25° 26° Deli 20° 34° 25° 26° Deli 20° 34° 25° 26° Deli 20° 34° 25°... -
Page 15: Electrical Schematics
Rev. 0505 Electrical Schematics... - Page 16 VGM, VGD-0505 Electrical Schematics (Continued)
- Page 17 Rev. 0505 Electrical Schematics (Continued)
- Page 18 VGM, VGD-0505 Electrical Schematics (Continued)
- Page 19 Rev. 0505 Electrical Schematics (Continued)
- Page 20 VGM, VGD-0505...
-
Page 21: Appendices
1.1 The installer is responsible for following the installa- tion instructions and recommendations provided by Appendices Hussmann for the installation of each individual type refrigerator. 1.2 Refrigeration piping should be sized according to Hussmann’s equipment recommendations and installed in accordance with normal refrigeration practices. -
Page 22: Appendix D. - Recommendations To User
1.2 Load levels as defined by Hussmann must be observed. 1.3 The best preservation is achieved by following these rules: Buy quality products. -
Page 23: Limited Warranty
On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assem- bly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure. - Page 24 VGM, VGD-0505 Service Record Last service date: Additional copies of this publication may be obtained by contacting: ® Hussmann Chino 13770 Ramona Avenue • Chino, California 91710 (909) 628-8942 FAX (909) 590-4910 (800) 395-9229 /Chino The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit.