HELI G Series Operation & Service Manual page 63

2.Monitoring
1.Parameter setup
controller monitoring
1.1
Hourmeter
reset to
2.2.1 Pump
zero OK
motor
phase
current
1.2.1
Single
1.2 Battery
charge
parameter
full
setting
2.2.2 Pump
voltage
motor
speed
1.2.2
Single
1.3 Liquid
charge
crystal
null
contrast
voltage
percentage
2.2.3 Pump
controller
1.2.3
temperature
Single
1.4
discharg
Percentage
e full
of pump
voltage
power
forbidden
2.2.4 Pump
1.2.4
motor
Single
temperature
discharg
1.5
e null
Password
voltage
Setting
1.5.1 The 1.5.2 New
password input password
（2）Parameter description corresponding to the numbered part of the above table
◆Start screen ON/OFF: Enable and turn off the starting screen of the instrument;
◆type of driver fault 1/2： 1 represents that the communication type of driver fault is
CAN communication, 2 represents that the communication type of driver fault is Fault
code communication; (instrument with this function can be configured with this)
◆Type of pump control failure 1/2: 1 represents that the communication type of
pump control failure is CAN communication, 2 represents that the communication type of
pump control failure is Fault code communication; (instrument with this function can be
Main display interface
3.Start Screen
menu ON/OFF
2.2 Pump motor
2.1.1 Accelerator
instruction
2.1.5 brake pedal
mapping
2.1.9 Interlock
condition
2.1.13 switch 3 status
2.1.17 switch 7 status
2.1.21 driver 2 status
2.1.25 driver 6 status
2.1.29 12V output
2.1.33 Proportional
drive output
2.1.37 Lock line
voltage
2.1.41 Controller
temperature
2.1.45 Controller
overtemperature limit
2.1.49 Regeneration
limit
Long press the enter key 5S to enter the
menu from the main display interface
4.Type of drive 5.Type of pump
fault 1/2 control failure 1/2
2.1 Drive motor
controller monitoring
2.1.2 Accelerator 2.1.3 accelerator
mapping voltage
2.1.6 brake pedal 2.1.7 simulator 1
voltage input
2.1.10 specified
2.1.11 switch 1 status
direction
2.1.14 switch 4 status 2.1.15 switch 5 status
2.1.19 switch 16
2.1.18 switch 8 status
status
2.1.22 driver 3 status 2.1.23 driver 4 status
2.1.27 inside 15V
2.1.26 driver 7 status
output
2.1.30 External 2.1.31 Main
supply current contactor driver
2.1.34 driver 3 output 2.1.35 output torque
2.1.39 motor
2.1.38 motor speed
temperature
2.1.42 Main
2.1.43 running status
contactor status
2.1.46 Under voltage 2.1.47 Overvoltage
limit limit
2.1.50 battery voltage
60
6.Clock setup
2.1.4 brake pedal
instruction
2.1.8 simulator 2
input
2.1.12 switch 2 status
2.1.16 switch 6 status
2.1.20 driver 1 status
2.1.24 driver 5 status
2.1.28 5V output
2.1.32 Proportional
control current
2.1.36 capacitor
voltage
2.1.40 Speed phase
current
2.1.44 Motor
overtemperature limit
2.1.48 Drive fault
limit ratio