TSUNESS TSOL-H3.0K-H User Manual
  1. Manuals
  2. Brands
  3. TSUNESS Manuals
  4. Inverter
  5. TSOL-H3.0K-H
  6. User manual

TSUNESS TSOL-H3.0K-H User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TSOL-H3.0K-H
TSOL-H3.6K-H
TSOL-H4.0K-H
TSOL-H4.6K-H
TSOL-H5.0K-H
TSOL-H6.0K-H

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TSOL-H3.0K-H and is the answer not in the manual?

Questions and answers

Related Manuals for TSUNESS TSOL-H3.0K-H

Summary of Contents for TSUNESS TSOL-H3.0K-H

  • Page 1 TSOL-H3.0K-H TSOL-H3.6K-H TSOL-H4.0K-H TSOL-H4.6K-H TSOL-H5.0K-H TSOL-H6.0K-H...

  • Page 3: Table Of Contents

    Content 1 Notes on this Manual............................1 1.1 Scope of Validity ............................1 1.2 Target Group ..............................1 1.3 Symbols Used .............................1 2 Safety ..................................2 2.1 Important Safety Instructions .........................2 2.2 Explanation of Symbols ..........................6 2.3 CE Directives...............................7 3 Introduction................................8 3.1 Basic features.............................8 3.2 Work Modes............................
  • Page 4 8 Troubleshooting..............................46 8.1 Trouble shooting ............................ 46 8.2 Routine maintenance ..........................49 9 Decommissioning ............................... 50 9.1 Remove the Inverter ..........................50 9.2 Packaging ..............................50 9.3 Storage and Transportation ......................... 50 10 Warranty Card..............................51...

  • Page 5: Notes On This Manual

    1 Notes on this Manual 1.1 Scope of Validity This manual is an integral part of TSOL Inverter, it describes the assembly, installation, commissioning, maintenance and failure of the product. Please read it carefully before operating. TSOL-H3.0K-H TSOL-H3.6K-H TSOL-H4.0K-H TSOL-H4.6K-H TSOL-H5.0K-H TSOL-H6.0K-H...

  • Page 6: Safety

    2 Safety 2.1 Important Safety Instructions Danger! Danger to life due to high voltages in the inverter!  All work must be carried out by qualified electrician.  The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  • Page 7 Warning!  Authorized service personnel must disconnect both AC and DC power from inverter before attempting any maintenance or cleaning or working on any circuits connected to inverter. Warning! Do not operate the inverter when the device is running. Warning! Risk of electric shock! ...
  • Page 8  Surge protection devices (SPDs) for PV installation WARNING！ Over-voltage protection with surge arresters should be provided when the PV power system is installed. The grid connected inverter is not fitted with SPDs in both PV input side and MAINS side. ...
  • Page 9  PE Connection and Leakage Current  The end-use application shall monitor the protective conductor by residual current operated protective device (RCD) with rated fault current Ifn≤240mA which automatically disconnects the device in case of a fault.  The device is intended to connect to a PV generator with a capacitance limit of a bout 700nf.

  • Page 10: Explanation Of Symbols

    3: Put on rubber shoes and gloves. 4: Do not place metallic tools and similar metallic parts on the batteries. 5: Switch off load connected to the batteries before dismantling battery connection terminals. 6: Only personal with proper expertise can carry out the maintenance of accumulator batteries.

  • Page 11: Ce Directives

    2.3 CE Directives This chapter follows the requirements of the European low voltage directives, which contains the safety instructions and conditions of acceptability for the end use system, which you must follow when installing, operating and servicing the unit. If ignored, physical injury or death may follow, or damage may occur to the unit.

  • Page 12: Introduction

    3 Introduction 3.1 Basic features TSOL Series is a high-quality inverter which can convert solar energy to AC energy and store energy into battery. The inverter can be used to optimize self-consumption, store in the battery for future use or feed-in to public grid. Work mode depends on PV energy and user‟s preference. It can provide power for emergency use during the grid lost by using the energy from battery and inverter (generated from PV).
  • Page 13 · WIRING SYSTEM FOR O Version To Battery...
  • Page 14 I Version applies to the wiring rules that require Neutral line of alternative supply must NOT be isolated or switched (applies to wiring rules AS/NZS_3000:2012 for Australia and New Zealand). Meter...
  • Page 15 · WIRING SYSTEM FOR I Version To Battery...

  • Page 16: Work Modes

    Note！  Please control the home loads, and make sure it‟s within the “EPS output rating” under EPS mode, otherwise the inverter will shut down with an “overload fault” warning.  Please confirm with the mains grid operator whether there are any special regulations for grid connection.
  • Page 17 Work mode: Force time use Priority: battery>load>grid (when charging) Priority: load>battery>grid (when discharging) This mode applies the area that has electricity price between peak and valley. User can use off-peak electricity to charge the battery. The charging and discharging time can be set flexibly, and it also allows to choose whether charge from the grid or not.

  • Page 18: Dimension

    Work mode: Peak and valley mode Priority: battery>load>grid(when charging) Priority: load>grid(when discharging) Charge the battery according to the set power within the set charging time; During the set discharge time, the battery is discharged according to the set power. Other time according to Self Use mode EPS Status When the grid is off, system will supply emergency power from PV or battery to...

  • Page 19: Terminals Of Pv Inverter

    3.4 Terminals of PV inverter Object Description DC switch (optional) PV connection area Battery connection area Waterproof valve EPS output GRID output BMS/Meter DI/DO WiFi/RF port for external Pocket WiFi/RF Warning! Qualified electrician will be required for the installation.

  • Page 20: Technical Data

    4 Technical Data 4.1 DC input TSOL-H6 TSOL-H3 TSOL-H3 TSOL-H4 TSOL-H4 TSOL-H5 Model .0K-H .0K-H .6K-H .0K-H .6K-H .0K-H Max. recom me nd ed DC power [W] 5000 5500 6000 6500 7000 7200 Max. DC voltag e[ V] Nominal DC operating voltage[V] MPPT voltage range [V] 100-560 MPPT voltage range @full load [V]...

  • Page 21: Internal Charger

    4.3 Internal Charger TSOL-H3. TSOL-H3. TSOL-H4. TSOL-H4. TSOL-H5. TSOL-H6. Model 0K-H 6K-H 0K-H 6K-H 0K-H 0K-H Battery type Lithium battery Battery voltage range [V] 90-400 Recommended battery voltage [V] Recommended battery capacity 4.8-16.8 [KWh] Max. charge/discharge current [A] 20A (adjustable) Peak charge/discharge current [A] 30A, 30s Communication interfaces...

  • Page 22: Eps Output (Apply To Version O, I)

    4.5 EPS output (apply to version O, I) TSOL-H3. TSOL-H3. TSOL-H4. TSOL-H4. TSOL-H5. TSOL-H6. Model 0K-H 6K-H 0K-H 6K-H 0K-H 0K-H EPS rated power [VA] 3000 3700 4000 4600 5000 6000 Max. EPS power [VA] 3000 3700 4000 4600 5000 6000 EPS rated voltage [Vac], 230, 50/60...

  • Page 23: Installation

    5 Installation 5.1 Check for Physical Damage Make sure the inverter is intact during transportation. If there is any visible damage, such as cracks, please contact your dealer immediately. 5.2 Packing Vers ion Vers ion I O&U Object Description Inverter Bracket 4 Expansion tubes &...

  • Page 24: Installation Precaution

    Quality certification Product manual 5.3 Installation Precaution  Installation Precaution TSOL Series inverter is designed for outdoor installation (IP 65). Make sure the installation site meets the following conditions:  Not in direct sunlight.  Not in areas where highly flammable materials are stored. ...

  • Page 25: Space Requirement

    5.4 Space Requirement 300mm Position Min. Size Side 300mm 300mm 300mm 300mm Bottom 300mm Front 300mm 300mm 5.5 Installation steps Tools required for installation. Installation tools: crimping pliers for binding post and RJ 45, screwdriver, manual wren ch andφ8 driller. Step 1: Screw the wall bracket on the wall Place the bracket on the wall and mark down the position of the 4 holes.
  • Page 26 Step1 Step2 Fasten the inverter on the back board with screws M5*12 (the same as the other side). Recommended installation of anti-theft lock (user owned). Step3...

  • Page 27: Electrical Connection

    6 Electrical Connection 6.1 PV connection TSOL Inverter can be connected in series with 2-strings PV modules for 3.0kW, 3.7kW, 4kW, 4.6kW ,5kW and 6kW. Select PV modules with excellent function and reliable quality. Open-circuit voltage of module arrays connected in series should be <Max. DC input voltage; operating voltage should be conformed to MPPT voltage range.
  • Page 28 Connection Steps: Step1. Checking PV module. 1.1 Use multi-meter to measure module array voltage. 1.2 Check the PV+ and PV- from the PV string combiner box correctly. 1.3 Please make sure the impedance between the positive pole and negative pole of PV to earth should be MΩ...

  • Page 29: Grid Connection

    Step5. Overview of PV connection 6.2 Grid Connection TSOL series inverter is designed for single phase grid. Voltage is 220/230/240V, frequency is 50/60Hz. Other technical requests should comply with the requirement of the local public grid. Table 4: Cable and Micro-breaker recommended TSOL-H3.0 TSOL-H3.6 TSOL-H4.0...
  • Page 30 3.1 Choose the appropriate wire (Cable size: refer to Table 4). 3.2 Reserve about 60mm of conductor material sectional area. 3.3 Remove 12mm of insulation from the end of wire. 3.4 Insert stripped wires into AC terminal and ensure that all conductor strands are captured in the AC terminal.

  • Page 31: Eps Connection (Apply To O Version And I Version Only)

    6.3 EPS Connection (apply to O Version and I Version only) TSOL series inverter has On and Off grid function, the inverter will deliver output power through AC port when the grid is on, and it will deliver output power through EPS port when the grid is off.
  • Page 32 O Version O Version O Version O Version Please contact our sales for any compatible connector purchase requirement. Note！ In case of discrepancies between wiring mode of local policy and the operation guide above, especially for the wiring of neutral line, grounding and RCD, please contact us before any operation!
  • Page 33  Connection Steps: Step1. Make EPS wires. 1.1 Choose the appropriate wire (cable size: refer to picture below). 1.2 Reserve about 60mm of conductor material sectional area. 1.3 Remove 12mm of insulation from the end of wire. 1.4 Insert stripped wires into AC terminal and insure all conductor strands are captured in the AC terminal.
  • Page 34  Requirements for EPS load Warning!  Make sure the EPS load power rating is within EPS output rating, otherwise the inverter will shut down with an “over load” warning.  When an “over load” is appeared, adjust the load power to make sure it is within the EPS output power range, then turn the inverter back on.

  • Page 35: Battery Connection

    6.4 Battery Connection Charging & discharging system of TSOL series Hybrid inverter is designed for high-voltage lithium battery. Before choosing battery, please note the maximum voltage of battery can not exceed 400V and the rated voltage of battery can not exceed 350V, and the battery communication should be compatible with TSOL inverter.
  • Page 36  BMS PIN Definition Communication interface between inverter and battery is CAN with a RJ45 connector. Definition BMS_CANH BMS_CANL Note！ The battery communication can only work when the battery BMS is compatible with the inverter.  Power Connection Steps: Step1. Choose the 9 AWG wire and strip the cable to 15mm. Step2.
  • Page 37 Step5 Note: BAT port, not PV port! Note: The positive line and negative line are not allowed to access anti -Line.  Communication Connection Steps: Step1. Disassemble the BMS/Meter cable gland. Step2. Prepare a communication cable (without sheath) and insert the communication cable through the cable nut.

  • Page 38: Meter Connection

    6.5 Meter Connection Meter is used for monitoring the power usage for entire house, in the meantime, inverter will also need the data from Meter to achieve the Export Control Function. Note！ It is necessary to connect meter to inverter otherwise inverter will shut down with a“Meter fault”alert.
  • Page 39 Step3 Step4...

  • Page 40: Drm Connection

    6.6 DRM Connection DRM is provided to support several demand response modes by emitting control signals as below. Note: pin definitions as below. DRM1/5 DRM2/6 DRM3/7 DRM4/8 +3.3V DRM0  DRM Connection Steps: Please refer to BMS connection steps for RJ45 connection. Please kindly note the PIN definition and port position will be slightly different.

  • Page 41: Wifi Connection

    6.8 WiFi Connection Inverter provides a WiFi port which can collect data from inverter and transmit it to monitoring-website via a Pocket WiFi. (Purchase the product from supplier if needed)  Diagram  WiFi Connection Steps: Step1. Plug Pocket Wifi into “WiFi” port at the bottom of the inverter. Step2.

  • Page 42: Inverter Manipulation

    6.10 Inverter Manipulation  Start inverter after checking all below steps: ① Ensure the inverter fixed well on the wall. ② Make sure all the DC writings and AC writings are completed. ③ Make sure the meter is connected well. ④...
  • Page 43  Check the inverter: Step1. Check the status of indicators and LCD screen. The left indicator should be green and the indicator screen should display the main interface. Note！ If the right indicator is red please check below the three points: - All the connections are correct.

  • Page 44: Setting

    7 Setting 7.1 Control Panel Object Name Description Display the information of the inverter. Screen lit in green: The inverter is in normal status. flash in green: The inverter is in wait status. Indicator Off: The inverter is in fault status. lit in red: The inverter is in fault status.

  • Page 45: Menu Structure

    7.2 Menu Structure Output Solar Battery Output Yield Solar Yield Bat Charge Bat Discharge EPS Yield Charge From Grid Event List Safety Date Time Italy Auto Test Buzzer Work Mode Advanced (Need Password) Bat.Para. Yield Model Export Limit Reset EPS Status Reset Event List DSP1 SW...

  • Page 46: Lcd Operation

    7.3 LCD Operation 7.3.1 Home interface Enter home interface automatically after startup. This interface shows the power flow direction and run status of the whole system. As shown in figure. (KW) 01-01 Normal 00:00 7.3.2 status The status function contains four items instantaneous data of the inverter. There are inverter output data, photovoltaic panel input data, battery data, EPS data.
  • Page 47 CEI0-21 NRS097-2-1 VDE0126-Greece-Island IEC61727-In G59-3 VDE0126-Greece-Continent France-VFR2014 France-Island-50Hz France-Island-60Hz AS4777-NZ Taiwan 7.3.8 Work Mode There are five work modes for choice. Parameter Comment The PV generated power will be used to supply the local loads firstly, then to charge the battery. The redundant power will export Self Use to the public grid.

  • Page 48: Quick Start Settings

    This function allows the inverter able to control energy. This value affects the grid power of feed in. 7.3.11 Reset User can reset inverter energy, overload error, event list, and restore factory default settings. 7.4 Quick Start Settings When the inverters first turn on, users need to set the following parameters to use. 7.4.1 date time This interface is for user to set the system date and time.
  • Page 49 7.4.5 work mode There are five work modes for user choice. Self Use(default), Forc e Time Use, Back Up Mode, Feed in Priority, Peak Valley Mode. Users can choose the appropriate mode according to their own needs. Work Mode Self Use -OK- After all the above parameters are set up, the inverter starts to run.

  • Page 50: Troubleshooting

    8 Troubleshooting 8.1 Trouble shooting This section contains information and procedures for solving possible problems with TSOL Series Hybrid inverters, and provides you with troubleshooting tips to identify and solve most problems that could occur with the TSOL inverters. This section will help you narrow down the source of any problems you may encounter. Please read the following troubleshooting steps.
  • Page 51 Check if the battery input voltage is within the normal range Or seek help from us The grid voltage is out of range for the last 10 Minutes. AC10M Volt Fault The system will back to normal if the grid is back. Or seek for help from us.
  • Page 52 Or seek help from us, if can not go back to normal state. Hybrid Relay Fault. Hybrid Relay fault Disconnect PV+ / PV- , grid and battery, reconnect them. Or seek help from us, if can not go back to normal state. BMS Communication Lost BMS Lost Check if the BMS cable is loose or broken...

  • Page 53: Routine Maintenance

    Contact TSUNESS Customer Service for further assistance. Please be prepared to describe details of your system installation and provide model and serial number of the unit. 8.2 Routine maintenance Inverters do not need any maintenance or correction in most condition, but if the inverter often loses power due to overheating, this can be the following reason: The cooling fins on the rear of house are covered by dirties.

  • Page 54: Decommissioning

    9 Decommissioning 9.1 Remove the Inverter Disconnect the inverter from DC Input and AC output. Wait for 5 minutes for de-energizing. Disconnect communication and optional connection wiring. Remove the inverter from the bracket. Remove the bracket if necessary 9.2 Packaging Please pack the inverter with the original packaging.

  • Page 55: Warranty Card

    10 Warranty Card Customer Information ☆ Name: ☆ Address: City: State: Zip Code: Tel: Fax: E-mail: System Information ☆ Model of Products: System Commissioning Date: ☆ Date of Bill of Lading: No. of Products Used: ☆ No. of Fault Products: ☆...

This manual is also suitable for:

Tsol-h3.6k-hTsol-h4.0k-hTsol-h4.6k-hTsol-h5.0k-hTsol-h6.0k-h

Table of Contents