Page 1
LI1BV Series User’s Manual NO. G03-LI1BV-F Revision: 1.0 Release date: March 17, 2022 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Page 2
Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.
Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 40 centigrade is the suitable temperature. (The temperature comes from the request of the chassis and thermal solution) ...
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
Chapter 1 Introduction of the Motherboard 1-1 Feature of Motherboard Onboard Intel ElkhartLake series processor ® Support 1* DDR4 3200MHz SO-DIMM up to 32GB and single channel function Integrated with Intel i225V 2.5GbE LAN chip (dual-chip optional by order ) ...
1-2 Specification Spec Description Design Mini-ITX form factor 6 layers; PCB size: 17.0x17.0cm Integrated Intel ElkhartLake series CPU ® Embedded CPU * for detailed CPU support information please visit our website Memory Slot 1*DDR4 SO-DIMM slot support 1* DDR4 3200MHz up to 32GB ...
Model LI1BV-00: 1* 9-Pin USB 2.0 header Model LI1BV-0L: 2* 9-Pin USB 2.0 headers 1* 4-Pin USB 2.0/1.1 wafer for 1* USB 2.0/1.1 port 1* SMBUS header 1* GPIO header 6* Serial port header (COM3/4/5/6 support RS232;COM1/2 support ...
Page 9
Motherboard Internal Diagram-Front For LI1BV-00 Series: 12V DC EDP Connector Power Connector 12V DC-in Jack LVDS Connector VGA port DDR4 SODIMM Slot USB 3.1(Gen.2) Ports Inverter Connector USB 2.0 Ports CPUFAN Connector SATA power Connector M.2 M-key (M2M1) SATAIII Port (SATA1) RJ-45 LAN Port M.2 E-key...
Page 10
For LI1BV-0L Series: 12V DC EDP Connector Power Connector 12V DC-in Jack LVDS Connector VGA port DDR4 SODIMM Slot USB 3.1(Gen.2) Ports USB 2.0 Header (FP_USB2) USB 2.0 Ports Inverter Connector CPUFAN Connector SATA power Connector M.2 M-key (M2M1) RJ-45 LAN Ports SATAIII Port (SATA1) M.2 E-key...
Page 12
Jumper Jumper Name Description JPCOM1 COM1 Header Pin9 Function Select 4-pin Block (2.0 pitch) JPCOM2 COM2 Header Pin9 Function Select 4-pin Block (2.0 pitch) JPCOM3 COM3 Header Pin9 Function Select 4-pin Block (2.0 pitch) JPCOM4 COM4 Header Pin9 Function Select 4-pin Block (2.0 pitch) M2M1 Connector Function Select...
Page 13
*Option for LI1BV-00 Series RJ-45 LAN Connector X1 *Option for LI1BV-0L Series LAN1 RJ-45 LAN Connector LINE-OUT Line-out Connector MIC Connector SPEAK_CON1 3W Amplifier Connector SIMCARD SIM card slot SATA1 SATAIII Connector SATAPWR1 SATA Power out Connector CPUFAN1 FAN Connector Light Control Connector Headers Header...
Chapter 2 Hardware Installation 2-1 Jumper Setting JPCOM1/2/3/4 (4-pin): COM1/2/3/4 Port Pin9 Function Select (2.0 pitch) JPCOM2 JPCOM3 JPCOM4 JPCOM1 JP2&JP3 (6-pin): M2M1 Connector Function Select (2.0 pitch)
Page 15
JPLCD1/JPLCD2 (4-pin): LCD Panel VCC Select (2.0 pitch) JPLCD2 JPLCD1 JPBKLT1 (3-pin): LVDS1/EDP1 LCD BACKLIGHT VCC Select (2.0 pitch) *Note:LI1BV series co-lay LVDS1 and EDP1 (EDP1 is optional by order;please refer to the actual model you purchased).
Page 18
Pin (7-8) of JPCLR1 (8-pin): CASE OPEN (2.0 pitch) PIN(7-8) CASE OPEN Pin1 7-8 Open: Normal(Default) Pin1 7-8 Closed: CASE OPEN M2M_PWR1 (3-pin): M.2 M-key Power Select (2.0 pitch)
Page 19
M2B_PWR1 (3-pin): M.2 B-key Power Select (2.0 pitch) M2E_PWR1 (3-pin): M.2 E-key Power Select (2.0 pitch)
Page 20
JP80P1 (2-pin): GPIO/80 Port Function Select (2.0 pitch) AT_MODE(3-pin): ATX Mode/AT Mode Select (2.0 pitch) *ATX Mode Selected: Press power button to power on after power input ready; AT Mode Selected: Directly power on as power input ready.
2-2 Connectors and Headers 2-2-1 Connectors (1) Rear Panel Connectors * Refer to Page-3 Rear IO Diagram. Icon Name Function 12V DC-in For user to connect compatible power adapter to Power Jack provide power supply for the system. To connect display device that support VGA specification.
Page 22
(2) ATX12V1 (4-pin block): ATX12V Type Power Connector (3) SATA1 (7-pin): SATA III Port connector SATA1 are high-speed SATAIII port that supports 6 GB/s transfer rate.
Page 23
(4) SATAPWR1 (4-pin): SATA HDD Power-Out Connector Pin 1 +12V (5) USB3 (4-pin): USB 2.0 Connector...
Chapter 3 Introducing BIOS Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website.
Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: ...
Chipset To change chipset configuration Security Password settings Boot To change boot settings Save & Exit Save setting, loading and exit options. User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted. Main Menu Main menu screen includes some basic system information.
3-7 Advanced Menu CPU Configuration Press [Enter] to make settings for the following sub-items: Intel(R) SpeedStep(tm) This item allows more than two frequency ranges to be supported. The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], user can make further setting in the following item: Turbo Mode Use this item to enable or disable processor Turbo Mode (requires EMTTM enabled too).
Page 38
to minimum speed when all cores enter C-State. The optional settings are: [Disabled]; [Enabled]. Package C State Limit Use this item to select the Maximum Package C State Limit Setting. The optional settings are: [C0/C1]; [C2]; [C3]; [C6]; [C7]; [C7S]; [C8]; [C9]; [C10]; [CPU Default];...
Page 39
When set as [Enabled], user can make further setting in the following item: Power Limit 2 Power Limit 1 in Milli Watts BIOS will round to the nearest 1/8W when programming. If the value is 0, BIOS will program this value as 1.25*TDP. For 12.50W, enter 12500.
Page 40
TPM 2.0 Device Found Security Device Support Use this item to enable or disable BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], user can make further settings in the following items: Active PCR Banks Available PCR Banks...
Page 41
The optional settings are: [Suspend Disabled]; [S3 (Suspend to RAM)]. ► Super I/O Configuration Press [Enter] to make settings for the following sub-items: Super IO Configuration ► Serial Port 1 Configuration/Serial Port 2 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable Serial Port (COM).
Page 42
The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], user can make further settings in the following items: Device Settings Change Settings Use this item to select an optimal setting for Super IO Device. The optional settings are: [Auto]; [IO=3F8h; IRQ=11;]; [IO=2F8h; IRQ=11]; [IO=3E8h;...
Page 43
WatchDog Wake-up Timer Value User can select a value in the range of [10] to [4095] seconds when ‘WatchDog Wake-up Timer Unit’ set as [Sec]; or in the range of [1] to [4095] minutes when ‘WatchDog Wake-up Timer Unit’ set as [Min]. WatchDog Wake-up Timer Unit The optional settings are: [Sec.];...
Page 44
matched on the other side. Long or noisy lines may require lower speeds. The optional settings are: [9600]; [19200]; [38400]; [57600]; [115200]. Data Bits The optional settings are: [7]; [8]. Parity A parity bit can be sent with the data bits to detect some transmission errors. The optional settings are: [None];...
Page 45
Putty KeyPad Use this item to select FunctionKey and KeyPad on Putty. The optional settings are: [VT100]; [LINUX]; [XTERMR6]; [SCO]; [ESCN]; [VT400]. Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection EMS Use this item to enable or disable Console Redirection. The optional settings are: [Disabled];...
Page 46
The optional settings are: [None]; [Hardware RTS/CTS]; [Software Xon/Xoff]. Data Bits The default setting is: [8]. *This item may or may not show up, depending on different configuration. Parity The default setting is: [None]. *This item may or may not show up, depending on different configuration. Stop Bits The default setting is: [1].
Page 47
Press [Enter] to make settings for the following sub-items: USB Configuration XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. The optional settings are: [Enabled]; [Disabled]. USB Mass Storage Driver Support Use this item to enable or disable USB Mass Storage Driver Support.
Page 48
IPv4 PXE Support Use this item to enable IPv4 PXE Boot Support. When set as [Disabled], IPv4 PXE boot support will not be available. The optional settings are: [Disabled]; [Enabled]. IPv6 PXE Support Use this item to enable IPv6 PXE Boot Support. When set as [Disabled], IPv6 PXE boot support will not be available.
The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], system will wake on the current time + increased minute(s). USB Power Gating S4-S5 USB Wake-up is affected by ERP function in S4. Please disable ERP before activating this function in S4. The optional settings are: [Enabled];...
Page 50
► System Agent (SA) Configuration Press [Enter] to make settings for the following sub-items: System Agent (SA) Configuration GTT Size Use this item to select the GTT Size. The optional settings are: [2MB]; [4MB]; [8MB]. DVMT Pre-Allocated Use this item to select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.
Page 51
► PCH-IO Configuration Press [Enter] to make settings for the following sub-items: PCH-IO Configuration PCI Express Configuration Press [Enter] to make setting for the following item: Peer Memery Write Enable Use this item to enable or disable Peer Memory Write. The optional settings are: [Disable];...
System State after Power Failure Use this item to specify what state to go to when power re-applied after a power failure (G3 state). The optional settings: [Always On]; [Always Off]; [Former State]. 3-9 Security Menu Security menu allow users to change administrator password and user password settings.
Page 53
Secure Boot Press [Enter] to make customized secure settings: System Mode Secure Boot Secure Boot feature is active if secure boot is enabled, Platform Key(PK) is enrolled and the system is in user mode. The mode change requires platform reset.
Page 54
Enroll Efi Image This item allows the image to run in Secure Boot mode. Enroll SHA256 Hash certificate of a PE image into Authorized Signature Database (db). Device Guard Ready Remove ‘UEFI CA’ from DB Restore DB default This item restore DB variable to factory defaults. Secure Boot variable/Size/Keys/Key Source Platform Key(PK)/Key Exchange Keys/Authorized Signatures/Forbidden Signatures/ Authorized TimeStamps/OsRecovery Signatures...
3-10 Boot Menu Boot Configuration Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Bootup NumLock State Use this item to select keyboard NumLock state. The optional settings: [On]; [Off]. Quiet Boot Use this item to enable or disable Quite Boot option.
3-11 Save & Exit Menu Save Changes and Reset This item allows user to reset the system after saving the changes. Discard Changes and Reset This item allows user to reset the system without saving any changes. Restore Defaults Use this item to restore /load default values for all the setup options. Save as User Defaults Use this item to save the changes done so far as user defaults.