Table of Contents
Advertisement
FOR THE USERS OF THE FAX
OR WIRELESS FUNCTION
Important safety instructions
•
If any of your telephone equipment is not operating properly, you should immediately
remove it from your telephone line, as it may cause harm to the telephone network.
•
Never install telephone wiring during a lightning storm.
•
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
•
Never touch uninsulated telephone wires or terminals unless the telephone line
has been disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
•
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
•
Do not use a telephone to report a gas leak in the vicinity of the leak.
•
Do not install or use the machine near water, or when you are wet. Take care not
to spill any liquids on the machine.
•
Save these instructions.
FAX interface cable and Line cable
To reduce the risk of fire, use only UL-Listed No.26 AWG or larger telecommunication line cord.
About the Telephone Consumer Protection Act of 1991
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use
a computer or other electronic device, including FAX machines, to send any message
unless such message clearly contains in a margin at the top or bottom of each transmitted
page or on the first page of the transmission, the date and time it is sent and an
identification of the business or other entity, or other individual sending the message and
the telephone number of the sending machine or such business, other entity, or individual.
(The telephone number provided may not be a 900 number or any other number for which
charges exceed local or long-distance transmission charges.)
In order to program this information into your FAX machine, you should complete the following steps:
See "Own Name and Destination Set" of User's Manual.
FCC Notice to users
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
On this equipment is a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local telephone company.
For products approved after July 23, 2001, the REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, your telephone company may disconnect
your service temporarily. If possible, They will notify you in advance. If advance notice is not
practical, you will be notified as soon as possible. You will also be advised of your right to file a
compliant with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of your equipment. If this happens, the telephone
company will provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service. If the equipment is causing harm to the telephone network, your telephone
company may ask you to disconnect the equipment until the problem is resolved.
If you have any questions or problems which cannot be solved by reading this manual, please
contact.
Sharp Electronics Corporation
100 Paragon Drive, Montvale, New Jersey 07645-1779
Telephone: 1-800-BE-SHARP
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
This equipment connects to the telephone network through a standard USOC RJ-11C
network interface jack.
If your home has specially wired alarm equipment connected to the telephone line, ensure
the installation of this equipment does not disable your alarm equipment.
If you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
This equipment may not be used on coin service provided by the telephone company.
Connection to party lines service is subject to state tariffs.
Contact your state's public utility commission, public service commission or corporation
commission for more information.
Notice for users in the CANADA
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications. The Ringer Equivalence Number (REN) indicates the
maximum number of devices allowed to be connected to a telephone interface. The
termination of an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of ail the devices not exceed five. The REN of this
equipment is indicated on the machine.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm or more
away from person's body (excluding extremities: hands, wrists, feet and ankles).
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
CAN ICES-3(A)/NMB-3(A)
For indoor use only.
AVIS POUR NOS UTILISATEURS AU CANADA
Le présent produit est conforme aux spécifications techniques applicables
d'lnnovation, Sciences et Développement économique Canada.
L'indice d'équivalence de la sonnerie (lES) sert à indiquer le nombre maximal de
dispositifs qui peuvent être raccordés à une interface téléphonique. La terminaison d'une
interface peut consister en une combinaison quelconque de dispositifs, à la seule
condition que la somme des lES de tous les dispositifs n'excède pas cinq.
L'indice d'équivalence de la sonnerie (IES) de cet équipement est indiqué sur la machine.
Sharp Electronics of Canada Ltd.
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 Canada
Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées pour
un environnement non contrôlé et respecte les règles d'exposition aux fréquences
radioélectriques (RF) CNR-102 de l'ISDE. Cet équipement doit être installé et utilisé en
gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à
l'exception des extrémités : mains, poignets, pieds et chevilles).
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d'Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
(1) L'appareil ne doit pas produire de brouillage;
(2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Pour usage intérieur seulement.
Notice for users in Mexico
"La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la
que pueda causar su operación no deseada".
FOR THE ADMINISTRATOR
Settings mode password
The administrator password is required to change the machine's settings mode.
Settings mode can be changed from either the operation panel or using a
computer web browser. After setting up the machine, refer to [SETTINGS MODE]
in the User's Manual to set a new password.
Password for logging in from this machine
The factory default password for the machine is "admin".
Password for logging in from a computer
In the factory default state, the only account that can be used to log in from a web browser
is the "Administrator" account. When user authentication is enabled, a fixed user can be
specified as a login user. The default password of each account is shown below.
When you log in as an "Administrator", you can manage all settings that can be
accessed from a web browser.
User
users
Administrator
admin
Forwarding all transmitted and received data to the
administrator (document administration function)
This function is used to forward all data transmitted and received by the machine to a
specified destination (Scan to E-mail address, Scan to FTP destination, Scan to Network
Folder destination, or Scan to Desktop destination).
This function can be used by the administrator of the machine to archive all transmitted
and received data.
To configure the document administration settings, click [Security Settings] and then [Document
Administration Function] in the Web page menu. (Administrator rights are required.)
•
The format, exposure, and resolution settings of transmitted and
received data remain in effect when the data is forwarded.
•
When forwarding is enabled for data sent in fax mode,
•
The [Direct TX] key does not appear in the touch panel.
•
Quick online transmission and dialing using the speaker cannot be used.
Points to notice when connecting to the network
When connecting the machine to the network, connect to the sub network (range divided
by the router) in which only the authorized device (such as PC) for the communication with
the machine in the protected LAN in some way like firewall is connected. And manage the
connected devices in the sub network so that the network condition may always be
maintained. Also use the filter setting function to prevent illegal access.
Account
Password
users
admin
5
Advertisement
Table of Contents
