AirKing D4D Operating Manual

AirKing D4D Operating Manual

Exhaust fan
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

IMPORTANT INSTRUCTIONS - OPERATING MANUAL
D4D, D4DG, D4DH, D4DGH
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN
THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock and
WARNING:
ELECTRIC SHOCK AND INJURY TO PERSON,
OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer.
b) Before servicing or cleaning the unit, switch power off at service panel
and lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as
a tag, to the service panel.
WARNING:
ELECTRIC SHOCK AND INJURY TO PERSON,
OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards, including fire-
related construction.
b) Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back
drafting. Follow the heating equipment manufacturer's guideline and
safety standards such as those published by the National Fire Protection
Association (NFPA) and the American Society for Heating, Refrigeration,
and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6727902 Rev. H 7/22
INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
injury to person, including the following:
TO REDUCE THE RISK OF FIRE,
TO REDUCE THE RISK OF FIRE,
SAVE THESE INSTRUCTIONS
CAUTION:
DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE
MATERIALS AND VAPORS.
d) Ducted fans must always be vented to the outdoors.
e) If this unit is to be installed over a tub or shower, it must be marked as
appropriate for the application and be connected to a GFCI (Ground Fault
Circuit Interrupter) – protected branch circuit.
f) Do not install in a ceiling with thermal insulation value greater than R40.
g) This unit must be grounded.
h) To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
i)
Read all instructions before installing or using exhaust fan.
WARNING:
WARNING:
OUTSIDE OF THE BUILDING HAS A STRONG EFFECT ON THE AIR
FLOW, NOISE AND ENERGY USE OF THE FAN. USE THE SHORTEST,
STRAIGHTEST DUCT ROUTING POSSIBLE FOR BEST PERFORMANCE, AND
AVOID INSTALLING THE FAN WITH SMALLER DUCTS THAN RECOMMENDED.
INSULATION AROUND THE DUCTS CAN REDUCE ENERGY LOSS AND
INHIBIT MOLD GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY
NOT ACHIEVE THEIR RATED AIRFLOW.
www.airkinglimited.com
Exhaust Fan
FOR GENERAL VENTILATING USE ONLY.
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY
SOLID-STATE SPEED CONTROL DEVICE.
DO NOT USE IN KITCHENS.
THE DUCTING FROM THIS FAN TO THE
1 of 12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D4D and is the answer not in the manual?

Questions and answers

Summary of Contents for AirKing D4D

  • Page 1 IMPORTANT INSTRUCTIONS - OPERATING MANUAL D4D, D4DG, D4DH, D4DGH Exhaust Fan READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2 SECTION 4 INSTALLATION INSTRUCTIONS Ducting CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE NOTE: 6" OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST PERFORMANCE. PANEL BEFORE STARTING INSTALLATION. CAUTION: SECTION 1 ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES.
  • Page 3 NOTE: There may be more than one white wire to be connected present. NOTE: The fan’s receptacle wires might need to be pulled outside compartment for connection. Screw Only pull the five loose wires outside of compartment. Additional wires will be present. NOTE: Unit must be grounded according to all local and national codes.
  • Page 4: Setting The Speed

    If the fan’s blower assembly was removed during the wiring process, reinstall the blower 2b. Locate the motion sensor on the fan’s grill and press the button 10 times. The LED on by reversing the directions in Section 5 (Wiring), Step 1b. the sensor will then flash the number of times to indicate the STANDARD MODELS: Plug the fan’s current setting, this will repeat 3 times:...
  • Page 5: Troubleshooting Guide

    Troubleshooting Guide Trouble Probable Cause Suggested Remedy 1. Fan does not operate when the switch is on. A fuse may be blown or a circuit tripped. Replace fuse or reset circuit breaker. Connector plug from motor is not plugged in. 1b. Turn off power to unit.
  • Page 6 REPLACEMENT PARTS DIAGRAM All Models Qty. Description Replacement Part # Mounting Rails 5S1299002 6" Metal Collar Assembly 5S5299100 Grill Springs 5S1202046 Mounting Channel 5S1202123 Blower Assembly 5S1250100 Fuse Harness Assembly 5S1250011 Light Lens 5S1239116 8 Watt LED Lamp 5S1250001 Specific to Model DL4S Qty.
  • Page 7 INSTRUCTIONS IMPORTANTES – MANUEL D’OPÉRATION Ventilateur combiner, DL4S, DL4SG, DL4SH, DL4SGH comprend lumière et ventilation LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ.
  • Page 8 SECTION 4 INSTRUCTIONS D’INSTALLATION ATTENTION : Conduits VOUS ASSURER QUE L’ALIMENTATION EST COUPÉE AU PANNEAU DE SERVICE AVANT DE COMMENCER L’INSTALLATION. NOTE: UN CONDUIT PLUS RIGIDE DE 6 PO OU PLUS EST RECOMMANDE POUR UNE MEILLEURE PERFORMANCE. SECTION 1 ATTENTION : TOUS LES CONDUITS DOIVENT ÊTRE CONFORMES AUX Préparation du Ventilateur d’évacuation CODES DU BÂTIMENT LOCAUX ET NATIONAUX.
  • Page 9 REMARQUE : Il peut y avoir plus d’un fil blanc à connecter. Compartiment de Câblage Extérieur : Enlever la vis du couvercle du compartiment à câblage et mettre ce couvercle dans un endroit fiable (Figure 5). REMARQUE : Les fils du réceptacle du ventilateur pourraient nécessiter d’être tirés à l’extérieur du compartiment pour le raccordement.
  • Page 10: Réglage De La Vitesse

    Si l’assemblage de la soufflante du ventilateur a été enlevé durant le processus de Réglage du temps minimum de fonctionnement. Ceci définit la durée minimale de fonctionnement à haute vitesse du ventilateur une fois qu’un mouvement est détecté raccordement, réinstaller la soufflante en inversant les instructions à l’étape 1b de la Section 5 Câblage.
  • Page 11: Utilisation Et Entretien

    SECTION 10 Fusible Suivez les étapes de la SECTION 5 Câblage pour accéder au Utilisation et entretien porte-fusible situé à l’intérieur du compartiment de câblage. ATTENTION : Pour remplacer le fusible, pressez le haut et le bas du porte- VOUS ASSURER QUE L’ALIMENTATION EST fusible ensemble tout en tournant le plus gros morceau dans COUPÉE AU PANNEAU DE SERVICE AVANT DE COMMENCER L’INSTALLATION.
  • Page 12 DIAGRAMME DES PIÈCES DE REMPLACEMENT Tous les modèles # de pièce de Qté. Description remplacement Traverses de Montage 5S1299002 Assemblée de collier en métal de 6 po 5S5299100 Ressorts de la grille 5S1202046 Canal de montage 5S1202123 Assemblée de la Soufflante 5S1250100 Assemblage du harnais de fusible 5S1250011...

This manual is also suitable for:

D4dgD4dhD4dgh

Table of Contents