Technical Specifications - Denon AVR-X3200W Service Manual

TECHNICAL SPECIFICATIONS

n Audio section
• Power amplifier
Rated output :
Front :
105W+105W(8Ω, 20Hz - 20kHz with 0.08% T.H.D.)
135W+135W(6Ω, 1kHz with 0.7% T.H.D.)
Center :
105W(8Ω, 20Hz - 20kHz with 0.08% T.H.D.)
135W(6Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
105W+105W(8Ω, 20 Hz - 20 kHz with 0.08% T.H.D.)
135W+135W(6Ω, 1 kHz with 0.7 % T.H.D.)
Surround back :
105W+105W(8Ω, 20 Hz - 20 kHz with 0.08% T.H.D.)
135W+135W(6Ω, 1 kHz with 0.7 % T.H.D.)
Output connectors : 4 - 16 Ω
• Analog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB (Direct mode)
S/N ratio : 100 dB (IHF-A, Direct mode)
Rated output : 1.2V
• Digital section
D/A output : Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input : Format — Digital audio interface
n Video section
• Color component video connector
Input/output level and impedance : Y signal — 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, –3 dB
n Tuner section
(Note : μV at 75 Ω, 0 dBf = 1 x 10
Reception frequency range :
Effective sensitivity :
50 dB sensitivity :
S/N ratio (IHF-A) :
P / C signal — 0.7 Vp-p, 75 Ω
B B
P / C signal — 0.7 Vp-p, 75 Ω
R R
W)
–15
FM 87.5 MHz - 107.9 MHz (for E3)
FM 87.5 MHz - 108.0 MHz (for E2, E1C)
AM 520 kHz - 1710 kHz (for E3)
AM 522 kHz - 1611 kHz (for E2, E1C)
FM 1.2 μV (12.8 dBf) (for E3)
FM 1.2 μV (12.8 dBf) (for E2, E1C)
AM 18 μV (for E3)
AM 18 μV (for E2, E1C)
MONO ― 2.8 μV (20.2 dBf)
MONO ― 70 dB (for E3)
MONO ― 78 dB (for E2, E1C)
STEREO ― 67 dB (for E3)
STEREO ― 67 dB (for E2, E1C)
Distortion :
n Wireless LAN section
Network type (wireless LAN standard) : Conforming to IEEE 802.11b
Security :
WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency :
2.4 GHz
No. of channels : 1 - 11 ch (for E3)
1 - 13 ch (for E2, E1C)
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo
are registered trademarks of the Wi-Fi Alliance.
n Bluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sight
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported profiles : A2DP (Advanced Audio Distribution Profile)1.2
AVRCP (Audio Video Remote Control Profile)1.4
Corresponding codec : SBC, AAC
Transmission range (A2DP) : 20 Hz - 20,000 Hz
z2 The actual communication range varies depending on the influence of
such factors as obstructions between devices, electromagnetic waves
from microwave ovens, static electricity, cordless phones, reception
sensitivity, antenna performance, operating system, application
software etc.
n General
Power supply : (for E3) :
(for E2) :
(for E1C) :
Power consumption : 600 W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 2.7 W
For purposes of improvement, specifications and design are subject to
change without notice.
9
MONO ― 0.7 % (for E3)
MONO ― 0.7 % (1 kHz) (for E2, E1C)
SRETEO ― 1.0 % (for E3)
SRETEO ― 1.0 % (1 kHz) (for E2, E1C)
Conforming to IEEE 802.11g
Conforming to IEEE 802.11n
(Wi-Fi® compliant)z1
AC 120 V, 60 Hz
AC 230 V, 50 Hz / 60 Hz
AC 220 V, 50 Hz