Technical Specifications - Denon AVR-X4200W Service Manual

TECHNICAL SPECIFICATIONS

n Audio section
• Power amplifier
Rated output :
Front :
125 W + 125 W ( 8 Ω, 20 Hz - 20 kHz with 0.05 % T.H.D.)
165 W + 165 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Center :
125 W ( 8 Ω, 20 Hz - 20 kHz with 0.05 % T.H.D.)
165 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
125 W + 125 W ( 8 Ω, 20 Hz - 20 kHz with 0.05 % T.H.D.)
165 W + 165 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround back / Height1 / Front wide :
125 W + 125 W ( 8 Ω, 20 Hz - 20 kHz with 0.05 % T.H.D.)
165 W + 165 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Dynamic power ：
130 W x 2-channel ( 8 Ω)
190 W x 2-channel ( 4 Ω)
Output connectors : 4 - 16 Ω
n Analog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB (Direct mode)
S/N ratio : 102 dB (IHF-A, Direct mode)
Distortion : 0.005 % (20 Hz – 20 kHz) (Direct mode)
Rated output : 1.2 V
n Digital section
D/A output : Rated output — 2V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, 0 dB )
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input : Format — Digital audio interface
n Phono equalizer section
Input sensitivity :
RIAA deviation :
S/N ratio :
Distortion factor :
n Video section
• Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 10 MHz — 0, –3 dB
• Color component video connector
Input/output level and impedance : Y signal — 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, –3 dB
2.5 mV
±1 dB (20 Hz to 20 kHz)
74 dB (IHF-A)
0.03 % (1 kHz, 3 V)
P / C signal — 0.7 Vp-p, 75 Ω
B B
P / C signal — 0.7 Vp-p, 75 Ω
B B
n Tuner section
(Note : μV at 75 Ω, 0 dBf = 1 x 10
Reception frequency range :
Effective sensitivity :
50 dB sensitivity : MONO ― 2.8 μV (20.2 dBf)
S/N ratio : MONO ― 70 dB (IHF–A weighted, Direct mode)
STEREO ― 67 dB (IHF–A weighted, Direct mode)
Distortion :
n Wireless LAN section
Network type (wireless LAN standard) : Conforming to IEEE 802.11b
Security : WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency : 2.4 GHz
No. of channels :
1 - 11 ch (for E3)
1 - 13 ch (for E2, E1C, JP)
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo
are registered trademarks of the Wi-Fi Alliance.
n Bluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sightz2
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported profiles : A2DP (Advanced Audio Distribution Profile)1.2
AVRCP (Audio Video Remote Control Profile)1.4
Corresponding codec : SBC, AAC
Transmission range (A2DP) : 20 Hz - 20,000 Hz
z2 The actual communication range varies depending on the influence of
such factors as obstructions between devices, electromagnetic waves
from microwave ovens, static electricity, cordless phones, reception
sensitivity, antenna performance, operating system, application
software etc.
n General
Power supply : (for E3) :
(for E2) :
(for E1C) :
(for JP) :
Power consumption : 670 W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 2.7 W
For purposes of improvement, specifications and design are subject to
change without notice.
9
–15
W)
FM 87.5 MHz - 107.9 MHz (for E3)
FM 87.5 MHz - 108.0 MHz (for E2, E1C)
FM 76.0 MHz - 95.0 MHz (for JP)
AM 520 kHz - 1710 kHz (for E3)
AM 522 kHz - 1611 kHz (for E2, E1C)
AM 522 kHz - 1629 kHz (for JP)
FM 1.2 μV (12.8 dBf)
AM 18 μV
MONO ― 0.7 % (1 kHz)
SRETEO ― 1.0 % (1 kHz)
Conforming to IEEE 802.11g
Conforming to IEEE 802.11n
(Wi-Fi® compliant)z1
AC 120 V, 60 Hz
AC 230 V, 50 Hz / 60 Hz
AC 220 V, 50 Hz
AC 100 V, 50 Hz / 60 Hz