Eller BA 300 Instruction Manual

Position during work
fall arrest system
attached to the back
attaching point
of the harness
Connecting of the strap
Adjusting of the strap
Shortening
Lengthening
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
Louis Reyners BV, Symon Spiersweg 13A,1506 RZ, Zaandam, The Netherlands ,Tel: +31 (0)756504750, fax +31 (0)756504760, www.lr.nl
Front view
suspension rope
connector
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Instruction Manual
Back view READ CAREFULLY BEFORE USE
1
2
3
4
5
6
7
Elements of the seat board
(1) Attachment connector,
(2) Suspension element,
(3) Suspension webbings,
(4) Connecting / Adjusting buckle,
(5) Waist strap,
(6) Croatch strap,
(7) Seat.
ADMISSIBLE TIME OF USE
The seat board can be used for 5 years. After this
PERIODIC
EXAMINATION period the device must be withdrawn from use to
NEXT DUE DATE
carry out manufacturer's detailed inspection
The manufacturer's inspection can be carried out
by:
- manufacturer
- or person recommended by manufacturer
- or company recommended by manufacturer
During this inspection
admissible time of use the seat board
manufacturer's inspection.
SEAT BOARD
BA 300
THE EQUIPMENT
the seat board shall only be used by a person trained and competent in its
!
safe use.
the seat board must be used in conjunction with full body harness and fall
!
arrest equipment.
the seat board is not personal protective equipment and must be never use
!
alone.
it is forbidden to make any alterations or additions to the
!
the manufacturer's prior written consent.
any repair shall only be carried out by
!
representative.
before use ensure about the compatibility of items of equipment assembled
!
into a fall arrest system. Periodically check connecting and adjusting of the
equipment components to avoid accidental loosening or disconnecting of the
components.
it is forbidden to use combinations of items of equipment in which the safe
!
function of any one item is affected by or interferes with the safe function of
another.
before each use of the seat board
!
of the equipment, to ensure that it is in a serviceable condition and operates
correctly before it is used.
during pre-use check it is necessary to inspect all elements of the equipment
!
in respect of any damages, excessive wear, corrosion, abrasion, cutting or
incorrect acting .
after every12 months of utilization,
!
use to carry out periodical detailed inspection. The periodic inspection must
be carried out by
a competent person for periodic inspection. The periodic inspection can be
carried out also by the manufacturer or his authorized representative.
In case of some types of the complex equipment e.g. some types of
retractable fall arresters the annual inspection can be carried out only by the
manufacturer or his authorized representative.
regular periodic inspections are the essential for equipment maintenance and
!
the safety of the users which depends upon the continued efficiency and
durability of the equipment.
during periodic inspection it is necessary to check the legibility of the
!
equipment marking.
it is essential for the safety of the user that if the product is re-sold outside the
!
original country of destination the reseller shall provide instructions for use, for
maintenance, for periodic examination and for repair in language of the
country in which the product is to be used.
the sear board must be withdrawn from use immediately when
!
arise about its condition for safe use and not used again until confirmed in
writing by equipment manufacturer or his representative after carried out the
detailed inspection.
the device must be withdrawn from use immediately and destroyed when it
!
have been used to arrest a fall.
a full body harness is the only acceptable body holding device that can be
!
,
used in a fall arrest system.
the anchor device or anchor point for the fall arrest system should always be
!
positioned, and the work carried out in such a way, as to minimise both the
potential for falls and potential fall distance. The anchor device/point should
be placed above the position of the user . The shape and construction of the
anchor device/point shall not allowed to self-acting disconnection of the
equipment. Minimal static strength of the anchor device/point is 1 kN. It is
recommended to use certified and marked structural anchor point complied
with EN795.
it is obligatory to verify the free space required beneath the user at the
!
workplace before each occasion of use the fall arrest system, so that, in the
case of a fall, there will be no collision with the ground or other obstacle in the
fall path. The required value of the free space should be taken from instruction
manual of used equipment.
the seat board must be transported in the package (e.g.: bag made of
!
moisture-proof textile or foil bag or cases made of steel or plastic) to protect it
against damage or moisture.
the seat board can be cleaned
!
on the materials in the manufacture of the equipment. For textile products use
mild detergents for delicate fabrics, wash by hand or in a machine and rinse in
water. Plastic parts can be cleaned only with water. When the equipment
becomes wet, either from being in use or when due cleaning, it shall be
allowed to dry naturally, and shall be kept away from direct heat.
will be established
the device should be stored loosely packed, in a well-ventilated place,
!
till next
protected from direct light, ultraviolet degradation, damp environment, sharp
edges, extreme temperatures and corrosive or aggressive substances.
seat board without
device manufacturer or his certified
it is obligatory to carry out a pre-use check
the seat board must be withdrawn from
any doubt
0
and desinfected without causing adverse effect