Table of Contents
Advertisement
Shipping
When turned on for the first time, the language
selection screen will be displayed. Select the desired
language and press ENTER.
On the next screen, set your country preference and
press ENTER to continue.
You will be asked to set and confirm a PIN at this point.
For some country options, the PIN cannot be set to
0000, in this case you need to enter another 4-digit
number combination. You have to enter this PIN if you
are asked to enter a PIN for any menu operation later.
The Set User Name and Password setting menu will
be displayed next.
Please press the password policy to check the contents
and make each setting.
The Signage Settings menu will be displayed next.
Set ID, OSD Orientation, Auto Software Update
options can be configured using this menu. Model
name, Serial number and Software version options
are for information only. They will be grayed out and
not selectable. You can save the model information
data of the Display to a connected USB device using
the Save model information option. You can also
copy database files from a connected USB device to
the Display using the Clone from USB option. Refer
to the Signage Settings Menu Content section for
more information on the options of this menu. After the
settings are completed, highlight Next and press
ENTER to continue.
Note: Make the Software Version of cloning source and
destination same. Make the Model (CQE1W, SQE1W) of
cloning source and destination same. After Clone from USB,
this display will reboot automatically.
The Display Operation Mode will be displayed next.
Power Mode is set to "Eco" ; Turn the power on in a
usual manner at power-on.
Power Mode is set to "Reactive" ; Quickly turns the
power on at power-on.
(Note) When this function is set to "Reactive", the
power consumption is increased in standby mode.
The Auto Launch Selection screen will be displayed
next. Open Browser and Disabled options will be
available. Highlight the desired option and press
ENTER to proceed.
On the next screen, the Network/Internet Settings
menu will be displayed. Please refer to Connectivity
section to configure a wired or a wireless connection.
If you want your Display to consume less power in
standby mode, you can disable the Networked
Standby Mode option by setting it as Off. After the
settings are completed highlight Next and press
ENTER button to continue.
The Shipping is completed.
To repeat this process and reset the Display's settings
to the factory defaults enter the Settings>Signage
menu, highlight Shipping and press ENTER. You will
be asked to enter the PIN that you have defined in the
First Time Installation. If the correct PIN is entered a
confirmation message will be displayed asking
whether you want to delete all settings and reset the
Display. Select Yes and press ENTER to confirm.
Note: Do not turn off the Display while initializing first time
installation. Note that, some options may not be available
depending on the country selection.
Note: If you forget the PIN, please contact the service company.
Note: The initial value of PIN is "0000".
Using Main Display
Menu
When the Menu button is pressed, the main Display
menu will appear at the left of the screen. You can
navigate through the menu items using the directional
buttons on the remote. To select an item or see the
sub-menu options of the highlighted menu press
ENTER
button.
When
option some of the sub-menu items of this menu may
appear on the upper side of the menu bar for quick
access. To use a quick access item highlight it, press
ENTER and set
as
Right
directional buttons. When finished press
ENTER or EXIT/RETURN button to exit.
Press EXIT button to close the main menu.
1. Home
When main menu is opened Home menu bar
will be highlighted. The content of the Home menu
can be customised by adding options from other
menus. Just highlight an option and press the
Down direction button on the remote. If you see Add
to Home option you can add it to the Home menu.
Same way you can delete or change the position of
any item in the Home menu. Press the Down
direction button and select Delete or Move option
and press ENTER. In order to move a menu item
use the Right and Left direction buttons to select the
position that you want the item to move to and press
ENTER.
2. Settings
You can manage the settings of your Display using the
options
of
this
Menu Contents section for more information.
If wait a few seconds or press the Up direction button
while Picture, Sound and System is highlighted, some
of the items in each menu will appear on the screen.
2.1. Off Timer
If wait a few seconds or press the Up direction button
while System is highlighted, the Off Timer will appear
as one of the items. Sets the time until the power is
turned off automatically.
Note: If the RECALL button is pressed while the Off Timer is
set, the remaining time is displayed in the upper right
corner on the screen. The Off Timer item is not in the System
menu.
3. Apps
When your Display is connected to the Internet related
contents will also be available, including Apps related
contents. Using the Apps menu you can access
your applications. Refer to Apps section for
more information.
4. Sources
You can manage your input source references using
the options of this menu. To change the current source
highlight one of the options and press ENTER.
4.1. Source Settings
Enable or disable selected source options. There
are also Regular, Enhanced and Disabled options
available for HDMI source. Regular and Enhanced
options are affecting the colour settings of the HDMI
source. To be able to watch 4K or HDR/HLG images
from the HDMI source its source setting should
be set as Enhanced if the connected device is
compatible with HDMI 2.0 and subsequent versions.
you
highlight
desired
using
the
menu.
Refer
to
English - 21 -
a
menu
Left/
Settings
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
