Advertisement
Others in the workplace should be kept at a safe distance from the drill, especially when it is in operation.
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
3 Avoid unintentional starting.
3
DO NOT use drill for a task it is not designed to perform.
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
7
the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of correctly.
7
DO NOT exceed the rated capacity of the drill.
DO NOT operate the drill if any parts are missing as this may cause failure or possible personal injury.
7
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT pull the cable to remove the plug from the power supply.
7
When not in use, switch off the drill, remove plug from the power supply and do not leave until the tool has come to a complete stop.
7
3
2. DESCRIPTION
The SDM150 bench drill is suitable for light industrial, agricultural and woodworking applications. The drill is fitted with a flip-up
safety guard and a “No Volt Release” switch, which prevents accidental restart after a mains power interruption. A rack and pinion feed
shaft with preset depth control for repetitive work is also included. The drill has a Morse Taper spindle to accept taper shank bits.
M o r t i c e a t t a c h m e n t s and work clamps are also available; contact your local Sealey dealer for information.
3. TECHNICAL SPECIFICATIONS
Model
Chuck size (mm)
Spindle Nose Taper
Swing (mm)
Chuck to Upright Face (mm)
Spindle Travel (mm)
Number of Speeds
Speed Range (rpm)
Spindle to Table - max. (mm)
Spindle to Base - max. (mm)
Working Table Diameter (mm)
Working Base (mm)
Overall Base (mm)
Column Diameter (mm)
Overall Height (mm)
Voltage (AC)
Motor Range - no load (W)
- under load (W)
Weight (kg)
5. ASSEMBLY
Note: Figures are illustrative and may differ in detail from your drill.
5.1.
Assembly
5.1.1. Place column assembly on base, align holes and secure with the four bolts and washers provided.
5.1.2. Install the table bracket onto the column together with the rack (fig.1), engaging gear in bracket with rack.
5.1.3. Install the rack collar and tighten firmly (fig.2).
5.1.4. Install the table adjusting handle (fig.2.A) and pivoted clamp bolt (the longer of the two - fig.2.B).
5.1.5. Tighten the handle set screw (with the hex. key provided) and the bracket clamp bolt.
5.1.6. Install the table and table pivoted clamp bolt (fig.3).
5.1.7. Carefully place the head assembly over the column and slide it into position. Align head with base.
5.1.8. Insert the two set screws in the right side of the head to lock it into position and tighten with hex. key (fig.4).
4. CONTENT
4.1. Content
SDM150
Check parts against the list below. If any items are damaged or missing contact
16
your supplier.
MT2
3 Head Assembly
3 Base
410
3 Column with Flange
170
3 Rack and Rack Ring
80
3 Feed Handles and Knobs (3)
3 Table Arm, Bracket and Worm
12
3 Adjusting Handle with Set Screw (table)
210 - 2220
3 Table
3 Pivoted Clamp Bolts (2 - table arm & bracket)
390
3 Arbor
640
3 Chuck and Key
290
3 Bolts and Washers (4)
3 Screw Knob (pulley cover)
184 x 200
3 Safety Guard
250 x 450
3 Set Screws (2)
3 Wedge
70
3 Hex. Keys (2)
1000
230
370
550
50
fig. 1
SDM150 - 0016 - (1) - 010600
Advertisement
