Overload Cut-Out; Cleaning And Maintenance; Troubleshooting - BorMann BBC2500 User Manual

EN
The charging current should be 1/10 to 1/6 of the battery capacity.
Note! Gases are released during the charging process. It is essential that you ventilate the rooms well.
As long as the equipment is charging, the LCD display shines green. If charging is complete, the LCD display shines blue (BBC4000)
Finishing charging the battery
• Pull the plug out of the socket
• First disconnect the black charging cable from the bodywork.
• Then release the red charging cable from the positive pole on the battery.
• Important! In case of positive earthing, first disconnect the red charging cable from the bodywork and then the black charging cable from the battery.
• Screw or push the battery stoppers back into position (if there are any).
Battery tester for 12V batteries for BBC4000
Connect the charger to the battery. The LCD symbol "H" (Fig. B) shows the charge status (1 increment = 25%). The battery voltage is shown on the LCD dis-
play.

Overload cut-out

The charger is equipped with electronic protection against overload, short circuit and swapped poles. One or more fine fuses are also fitted. If the fuse suffers
a defect it must be replaced by a new fuse with the same amp value. If necessary, please contact our customer service center.
Maintenance and care of the Battery
• Ensure that your battery is always fitted securely.
• A perfect connection to the cable network of the electrical system must be ensured at all times.
• Keep the battery clean and dry. Apply a thin coating of grease to the connection terminals using an acid-free, acid-resistant grease (Vaseline).
• Check the level of the acid in batteries that are not maintenance-free versions approximately every 4 weeks and top up with distilled water if necessary.
Cleaning & Maintenance
Danger! Always pull out the mains power plug before starting any cleaning work.
• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with com-
pressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool increases the risk of an electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned off the charging terminals.
There are no parts inside the equipment which require additional maintenance.cloth and some soft soap. Do not use cleaning agents or solvents; these could
attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an
electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned off the charging terminals.cloth and some soft soap. Do not use
cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an
electric tool increases the risk of an electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned off the charging terminals.

Troubleshooting

If the equipment is operated properly you should experience no problems with malfunctions or faults. In the event of any malfunctions or faults, please check
the following before you contact your customer services.
Fault Possible cause Remedy
- Connect the red clamp to the positive pole
- Charger clamps connected incorrectly
Equipment does and the back clamp to the bodywork
- Contact between the charger clamps
not charge up - Prevent contact
- Battery defective
- Have the battery checked by an expert and replace it if necessary
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes signif-
icantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also
concern other models of the manufacturer's product line with similar features and may not be included in the product you just acquired.
* Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or for equivalent purposes.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and
special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
6
WWW.BORMANNTOOLS.COM