Table of Contents
Advertisement
Quick Links
Flowmatic Tubular 2030 Electronic Soap Dispenser
Wall Mount
PRODUCT CODE:
-
TZ-FLOWSOAP1
SPECIFICATIONS
−
Touch-free electronic soap dispenser operated by infrared sensor.
−
The soap dispenser automatically activates when users place their hands within sensor range,
providing a measured amount of soap (adjustable by remote control).
−
If the users remove their hand before the full amount is dispensed, the soap dispenser immediately
stops the soap flow.
−
Chrome plated assembly for durability and easy cleaning.
TECHNICAL DATA
Capacity
Power supply for battery versions:
Soap viscosity
Standard discharge
Sensor range:
Pre-set sensor range
Finish
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
1 Litre
Battery models: Battery Box for 6xD Alkaline batteries
100 – 3800 cPs
1.4ml (customizable by optional remote control)
35-155 mm +/- 10 mm (customizable by optional remote control)
80 mm +/- 10 mm
Chrome
Version 1, 17 March 2021, Page 1 of 12
Advertisement
Table of Contents
Summary of Contents for Galvin Specialised Flowmatic Tubular 2030
- Page 1 1.4ml (customizable by optional remote control) Sensor range: 35-155 mm +/- 10 mm (customizable by optional remote control) Pre-set sensor range 80 mm +/- 10 mm Finish Chrome NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
- Page 2 Version 1, 17 March 2021, Page 2 of 12...
-
Page 3: Pack Contents
Version 1, 17 March 2021, Page 3 of 12 PACK CONTENTS 1 x Elbow and 1 x Wall rosette 1 x Body assembly for Tubular Soap Dispenser corrugated tube 1 x Soap tank with bottle support and pump assembly 1 x Battery Box for 6xD Alkaline Batteries 8 x Screws and Wallplugs 1 x Quick connection fitting 1 x Temporary base cover... -
Page 4: Installation
INSTALLATION IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and in accordance with your local regulatory requirements. Electrical supply conditions must also comply to the applicable national and/or state standards. - Page 5 Version 1, 17 March 2021, Page 5 of 12 4. Assemble spout: Cut / remove the temporary soap dispenser base cover. Fix the soap dispenser spout by inserting the 3. Assemble corrugated tube: nipple into the soap dispenser base and then tightening the screw.
-
Page 6: Filling The Soap Tank
Version 1, 17 March 2021, Page 6 of 12 IMPORTANT: connector should connected properly so that the white O-ring is not visible and a clicking sound is heard. FILLING THE SOAP TANK Unscrew the soap tank from the pump assembly and pull it out from the bottle support. - Page 7 Version 1, 17 March 2021, Page 7 of 12 Press the refill button located at the back of the pump assembly until soap starts coming out of the soap dispenser spout. This operation can also be done using the soap dispenser remote control Refill function.
-
Page 8: Battery Replacement
Version 1, 17 March 2021, Page 8 of 12 Once the soap tank has been filled \ refilled, press the FILL button. The pump will run for one minute, priming the piping with soap. Once soap begins dispensing from the spout, priming is complete. Press the FILL button again to stop the priming before the minute is over. -
Page 9: Maintenance
Version 1, 17 March 2021, Page 9 of 12 NOTE: Do not mix used batteries with new ones. Important: Spent batteries should not be disposed of with normal household waste. Contact your local authority for information on waste disposal and recycling. MAINTENANCE Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. - Page 10 Version 1, 17 March 2021, Page 10 of 12 Random discharge Reflection Eliminate any cause of reflection and if from the nozzle issue from necessary, use appropriate remote control basin or other to shorten detection range. object Soap discharging Damaged Replace the Pump.
- Page 11 Version 1, 17 March 2021, Page 11 of 12 Refill button Check operation with on pump does functioning battery pack. Where necessary, not activate replace batteries or replace the battery the pump. pack: Battery pack (without batteries) Damaged If the sensor is not even after changing sensor batteries then resolve this issue by replacing sensor.
-
Page 12: Warranty
Version 1, 17 March 2021, Page 12 of 12 WARRANTY The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin Engineering Pty.