Washing Instructions - Haier HT1600TXVE Operation Manual

Control Panel Operating Functions
Control Panel (HT1600TXVE/ME)
HT1600TXVE
Cashmere Super quick wash
Cotton
Synthetic Silk Rinse+Spin
Drain
Wool Duvet
Hand wash Spin
0 Power off
A Program knob
Turning this knob to select the required program Refer to Guide to
Operational Program Selection.
Note: This knob is at the same time a power switch; turn the
knob past "O", the power is on.
B Washing temperature button
Press this button to select the required washing temperature (
Refer to Guide to Program Selection for the maximum washing temperatures
for different programs.During temperature selection, the selected temperature will be
displayed automatically.Note: when " " is displayed, cold washing is selected. Now
"20" will be displayed in the digital area.
C Spinning speed button
Press this button to select the required spinning speed (0, 400, 600, 800, 1200, 1400, 1600rpm).
Refer to Guide to Program Selection for the maximum spinning speed for
different programs.During speed selection, the selected speed will be displayed auto-
matically.Note: when " " is displayed, no spinning is selected; when "
is displayed, the maximum speed of 1600rpm is selected.
D Start / Pause button
When the electric cable of the washing machine is plugged and a program is selected, after the
washing temperature, spinning speed and other required functions are set, lightly press this
button, ":" will be displayed and operation will start. During a wash cycle, press this button
lightly, the ":" sign will stop blinking and operation will pause. Press it again to resume
operation. Note: After operation is suspended, the washing temperature, spinning speed and other
functions can be reset. After that, press the Start/Pause button to continue operation.
E Washing load button
Before a washing program, press this button to set the required washing load (L--1~L--6), the
washing machine will automatically adjust the water consumption, heating time and washing time.
Users can select the washing load as required for economical operation.
Note: 1. "L 1--6" refers to the five levels of washing load. If the laundry is more than half
of the drum content, it is recommended to select L--5 orL--6; otherwise, select L--1~L--4.
2. Please adjust the detergent quantity as per the washing load selected
6
, 40, 60, 75, 90 C).
"
~

Washing Instructions

Take "Synthetic program " as an example (operation for other programs is similar):
1. Open the door, prepare the soiled laundry and load into the washing machine evenly, and close the door.
2. Connect the water inlet hose and drainage hose, turn the program knob at "0", and plug the power cable
of the washing machine.
3. Pull out the detergent drawer and put adequate detergent into compartment 2; put some liquid softener
into compartment 3 if needed. Note that the softener should not exceed the "MAX" mark on the softener box;
if pre-wash is required, put adequate detergent into compartment 1.
4. Set the program knob at "2", the program time, set temperature and speed will be shown on the display
screen, e.g. .
5. Select washing temperature, spinning speed and other functions:
1) Before operation, press the Temperature button to set the washing temperature if needed. The tempera-
ture will be displayed on the screen.
2) Press the Speed Button to set spinning speed if needed. The set value will be displayed on the screen.
3) Press the Wash Load button for economical operation. Now
button to select from L - - 1 to L - - 6, and the selected value will be displayed. If the button is not
pressed within 2 seconds, the current value is set.
4) Press the Soak button to select the soaking function. The corresponding icon will go on.
5) Press the Extra Rinse button if extra rinsing is needed. The rinse icon on the screen will go on.
6) Press the Prewash button if needed. The pre-wash icon on the screen will go on.
7) Press the Delay button if needed. will be blinking. Now press the Speed button or Temp button
to select the delay time (0-24 h). Each press of the Speed button will increase 30 minutes, and each press
of the Temp button will decrease 30 minutes. If the delay time is 3 hours,
the above set program time is 1:30 hours, the program will start in 1 hour and thirty minutes, and finish
in 3 hours (if soaking is not selected).
6. Press the Start/Pause button to start the program, the door lock icon will go on and the remaining time
will be displayed (":" is blinking). The current temperature will be shown in the heating indicator.
7. As operation goes on, the remaining time will be decreasing. If the Soak button is pressed, the current
remaining time is displayed during soaking, the soak icon begins blinking, and the program pauses. Press
the Soak button or the Start/Pause button again to resume execution of the program.
8. At the end of a program, will appear on the screen and the Door Lock icon will go off. Now turn
the program knob at "0", open the door and take out the laundry. Unplug the power cable and disconnect the
water inlet hose, the washing program ends.
Important: During execution of a program, the speed, temperature and function settings can be reset at some
stages.
Notes: 1. Do not turn the program knob again during execution of a program.
2. The time shown on the screen is for reference only. It may differ slightly depending on the filling water
temperature, heating temperature, and the laundry conditions during spinning. This is normal phenomenon.
will appear on the screen. Press the
will be displayed. As
14