Product Specifications - Goodman GMEC96 Series Manual

Heating Data
High Fire Input¹
High Fire Output¹
Low-Fire Input¹
Low-Fire Output¹
AFUE²
Temp. Rise Range (°F)
Vent Diameter³
No. of Burners
Circulator Blower
Available AC @ 0.5" ESP
Size (D x W)
Horsepower @ 1075 RPM
Speed
Filter Size (in²) (Qty)
Electrical Data
Min. Circuit Ampacity⁴
Max. Overcurrent (amps)⁵
Shipping Weight (lbs)
¹ Natural Gas BTU/h
² DOE AFUE based upon Isolated Combustion System (ICS)
³ Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2" or 3" in diameter, depending upon furnace
input, number of elbows, length of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirements and must be 2" or 3" diameter PVC.
⁴ Minimum Circuit Ampacity = (1.25 x Circulator Blower Amps) + ID Blower amps. Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require
larger wire sizes.
⁵ Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. May use fuses or HACR-type circuit breakers of the same size as noted.
Notes
• All furnaces are manufactured for use on 115 VAC, 60 Hz, single-phase electrical supply.
• Gas Service Connection ½" FPT
• Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical Code and/or all existing local codes.
• For bottom return: Failure to unfold flanges may reduce airflow by up to 18%. This could result in performance and noise issues.
• For servicing or cleaning, a 24" front clearance is required. Unit connections (electrical, flue and drain) may necessitate greater clearances than the minimum clearances listed above. In all
cases, accessibility clearance must take precedence over clearances from the enclosure where accessibility clearances are greater.
SS-GMEC96
Downloaded from ManualsNet.com
GMEC96 GMEC96 GMEC96
0303ANA 0403ANA 0603ANA
30,000 40,000 60,000
28,800 38,400 57,600
21,000 28,000 42,000
20,160 26,880 40,320
96 96
20 - 50 20 - 50 30 - 60
2" - 3" 2" - 3" 2" - 3"
2 2
1.5 - 2 1.5 - 3 1.5 - 3
11" x 6" 11" x 6" 11" x 6"
1/2 1/2
5 5
(1) 16 x 25 (1) 16 x 25 (1) 16 x 25
(side) or (side) or (side) or
(1) 14 x 25 (1) 14 x 25 (1) 14 x 25
(bottom) (bottom) (bottom)
8.6 8.6 8.6
15 15
106 106 110
search engine
GMEC96 GMEC96 GMEC96
0302BNA 0402BNA 0603BNB
30,000 40,000 60,000
28,800 38,400 57,600
21,000 28,000 42,000
20,160 26,880 40,320
96 96 96
20 - 50 20 - 50 35 - 65
2" - 3" 2" - 3" 2" - 3"
3 2 2
1.5 - 2 1.5 - 3 1.5 - 3
10" x 8" 10" x 8" 11" x 8"
1/2 1/2 1/2
5 5 5
(1) 16 x 25 (1) 16 x 25 (1) 16 x 25
(side or (side or (side or
bottom) bottom) bottom)
8 8
15 15 15
111 112 115
www.goodmanmfg.com

Product Specifications

GMEC96 GMEC96 GMEC96
0803BNA 0804CNA 1004CNA
80,000 80,000 100,000
76,800 76,800 96,000
56,000 56,000 70,000
53,760 53,760 67,200
96 96 96
35 - 65 25 - 55 35 - 65
2" - 3" 2" - 3" 2" - 3"
3 4 4
1.5 - 3 2.5 - 4 1.5 - 4
11" x 8" 11" x 10" 11" x 10"
1/2 1/2 3/4
5 5 5
(1) 16 x 25 (1) 16 x 25 (1) 16 x 25
(side or (side or (side or
bottom) bottom) bottom)
8 8 11.6 13.3
15 15 15
118 123 140
GMEC96 GMEC96
1005CNA 1205DNA
100,000 120,000
96,000 115,200
70,000 84,000
67,200 80,640
96 96 96
35 - 65 35 - 65
2" - 3" 2" - 3"
5 5 6
3 - 5 3 - 5
11" x 10" 11" x 11"
1 1 1
5 5 5
(1) 20 x 25 (1) 20 x 25
(bottom) (bottom)
or (2) 16 x or (2) 16 x
25 (side) 25 (side)
13.3 13.3
15 15 15
140 154
3