Table of Contents
Advertisement
Configuring the HP ESCON PA
To verify that the correct microcode is loaded according to the new instructions, enter the
Step 5
show controllers EXEC command. The display indicates the currently loaded and running microcode
version for each HP ESCON PA.
Step 6
To verify the contents of the configuration file, enter the show running-config EXEC command. You
can also verify that the correct software image is configured to load at system restart or reload by using
the show startup-config EXEC command.
Using Flash Memory
The following provides information on the different functions of Flash memory that you might need
when configuring microcode:
•
•
•
Copying a New Image to the Flash Memory Card on a Cisco 7200 Series Router
Copying a new image to a Flash memory card might be required when a new microcode image becomes
available. Use the command copy tftp:filename [ bootflash | slot0 | slot1 ]:filename for the copy
procedure, where tftp:filename is the source of the file and [ bootflash | slot0 | slot1 ]:filename is the
destination in onboard Flash memory or on either of the Flash memory cards.
The following example shows the output from the copy tftp:filename command for Cisco IOS
Release 12.0:
Router# copy tftp:xcpa28-6 slot0:xcpa28-6
Address or name of remote host [181.23.250.2]?
Accessing tftp://181.23.250.2/jdoe/xcpa218-6...
Loading jdoe/xcpa218-6 from 181.23.250.2(via Ethernet3/0):!
Expanding slot0:/xcpa218-6_kernel_ecpa4 (472086 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_kernel_xcpa (414940 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_802 (246184 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_cmpc (562804 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_csna (96488 bytes):!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_eca (460712 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_offload (91976 bytes):!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_pca (68844 bytes):!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_push (15492 bytes):!!!
Expanding slot0:/xcpa218-6_seg_sslc (827760 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_tcpip (161196 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Expanding slot0:/xcpa218-6_seg_tn3270 (680672 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
[OK - 4109312/8218624 bytes]
PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration
36
Copying a New Image to the Flash Memory Card on a Cisco 7200 Series Router, page 36
Using Additional Flash Memory Commands, page 37
Recovering from Locked Blocks, page 38
OL-3743-02
Advertisement
Table of Contents
