Makita HM0860C Instruction Manual page 7

Lubrication
This tool requires no hourly or daily lubrication because it
has a grease-packed lubrication system. It should be
relubricated after every 6 months of operation. Send the
complete tool to Makita Authorized Service Center for
this lubrication service. However, if circumstances
require that you should lubricate it by yourself, proceed
as follows.
Run the tool for several minutes to warm it up. Switch off
and unplug the tool.
Loosen the four screws (two short screws on the upper
side and two long screws on the lower side.) and remove
the handle.
Disconnect the terminal by pulling it. (Fig. 14)
Remove the crank cap by loosening the screws with a
screwdriver. Rest the tool on the table with the bit end
pointing upwards. This will allow the old grease to collect
inside the crank housing. (Fig. 15)
Wipe out the old grease inside and replace with a fresh
grease (30 g). Use only Makita genuine hammer grease
(optional accessory). Filling with more than the specified
amount of grease (approx. 30 g) can cause faulty ham-
mering action or tool failure. Fill only with the specified
amount of grease. (Fig. 16)
Reinstall the crank cap and secure with the screws.
Connect the terminal and reinstall the handle. (Fig. 17)
CAUTION:
• Be careful not to damage the terminal or lead wires
especially when wiping out the old grease or installing
the handle. (Fig. 18)
• Whenever reinstalling the handle, use the two short
screws for the upper side and two long screws for the
lower side.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Bull point
• Cold chisel
• Scaling chisel
• Grooving chisel
• Clay spade
• Bit grease
• Rammer
• Bushing tool
• Ground rod adapter
• Hammer grease
• Safety goggle
• Side handle (auxiliary handle)
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: chiseling
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation
manufacturer declare that the following Makita
machine(s):
Designation of Machine: Demolition Hammer
Model No./ Type: HM0860C
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorized
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30. 1. 2009
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
): 87 dB (A)
pA
): 98 dB (A)
WA
2
): 11.5 m/s
h,CHeq
2
as the responsible
Director
ENG905-1
ENG900-1
ENG901-1
ENH101-15
7