Specifications; Ec Declaration Of Conformity - Makita DTD134 Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Capacities
No load speed (min
Impacts per minute
Overall length
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for screw driving in wood, metal and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Model DTD134
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model DTD146
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DTD134
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DTD146
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K) : 2.0 m/s
Model
Machine screw
Standard bolt
High tensile bolt
-1
)
Net weight
D.C.14.4 V Model
D.C.18 V Model
) : 92 dB (A)
pA
) : 103 dB (A)
WA
) : 93 dB (A)
pA
) : 104 dB (A)
WA
2
) : 12.0 m/s
h
2
2
) : 15.5 m/s
h
2
DTD134
0 - 2,400
D.C. 14.4 V
1.2 - 1.4 kg
BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
5 ENGLISH
DTD146
4 mm - 8 mm
5 mm - 14 mm
5 mm - 12 mm
0 - 2,300
0 - 3,200
138 mm
D.C. 18 V
1.3 - 1.6 kg