Table of Contents
Advertisement
Quick Links
Operation Instructions for Mijia DC Frequency Conversion Tower Fan
Safety Instructions Please read this manual carefully and keep it properly
before.
Attention
Installation
Please be sure to install this product correctly according to the instructions, otherwise electric
shock, fire, personal injury and other damages will occur.
The tower fan has not been assembled, please do not connect the power supply.
Handling
When moving, be sure to stop the tower fan and unplug the power plug.
When moving, please hold the tower fan firmly to avoid machine damage or personal safety
caused by falling.
Using
If the product has abnormal noise, peculiar smell, high temperature, tilt, body shaking and other
abnormalities, please stop using it immediately.
Do not lean against or tilt the tower fan during operation.
Do not swing the tower fan body manually to avoid damage to the internal transmission
mechanism.
Advertisement
Table of Contents
Related Manuals for Xiaomi Mijia DC
Summary of Contents for Xiaomi Mijia DC
- Page 1 Operation Instructions for Mijia DC Frequency Conversion Tower Fan Safety Instructions Please read this manual carefully and keep it properly before. Attention Installation Please be sure to install this product correctly according to the instructions, otherwise electric shock, fire, personal injury and other damages will occur.
- Page 2 Power cord Please unplug the power cord from the power outlet before performing maintenance work or moving the tower fan. When pulling out the power cord, pull it up from the power plug. Do not pull the power cord. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from the manufacturer, its maintenance department or similar departments.
-
Page 3: Packing List
Do not use inappropriate power outlets. Before removing the rear grille, it must be ensured that the tower fan is disconnected. 包装清单 Packing List ① Tower fan main body ② front chassis ③ rear chassis ④ M5 screw × 2 ⑤ special wrench ⑥ operation manual Hint: The illustrations of products, accessories and user interfaces in the manual are all schematic diagrams for reference only. -
Page 4: Product Introduction
Product Introduction Top view of tower fan Timing adjustment key Air Volume/Timing Indicator Wi-Fi Indicator Shake the head key Sleep Wind Mode Indicator Mode Switch Key Natural Wind Mode Indicator Direct Blowing Mode Indicator Power Air volume adjusting key Rear grille, power cord outlet, chassis bottom chassis, front grille, tower fan main body... -
Page 5: Installation
Installation Step 1: Splice the chassis 定位柱 定位孔 底盘 Positioning column, positioning hole, chassis As shown in the figure, insert the positioning column of the rear chassis ③ into the positioning hole of the front chassis ② and press it to buckle it in place to splice the rear chassis and the front chassis into a flat chassis. - Page 6 Step 3: Arrange the power cord Install the power cord into the trunking at the bottom of the chassis, lead it out from the outlet of the power cord, and complete the installation of the tower fan. Hint: normally straighten out the power cord and load it into the trunking, which will not damage the power cord.
-
Page 7: Switch Off
Connect the power supply Insert the power plug into the qualified power socket, and after hearing the "beep" tone, the tower fan is successfully connected to the power supply. Switch on and off Switch on Press key and the tower fan starts to work. For the first time, the default is direct blowing mode, with 1 windshield. -
Page 8: Switch Mode
挡位 1 挡 2 挡 3 挡 4 挡 Gear 1st gear 2nd gear 3rd gear 4th gear 显示状态 *●●● **●● ***● **** Display Status Tip: * Lighted State ● Off State Switch Mode Press the key to switch the modes of direct blowing, natural wind and sleep wind, and the corresponding mode indicator lights will be on for a long time. - Page 9 定时 关闭定时 1 小时 2 小时 3 小时 4 小时 Timing Close Timing 1 hour 2 hours 3 hours 4 hours 显示状态 ●●●● *●●● **●● ***● **** Display Status Tip: * Lighted State ● Off State Connect Mijia APP This product has been connected to Mijia and can be controlled by Mijia APP or Classmate XiaoAi, and is interconnected with other products.
-
Page 10: Maintenance
Connect to Wi-Fi At the same time, press the key and the mode switch key for a long time. After hearing the long sound "beep", enter the waiting connection state and connect the device according to the APP prompt. Wi-Fi Indicator Display Status: 等待连接... - Page 11 After the rear grille and impeller are removed, clean with clean water or diluted neutral detergent, combined with soft cloth or sponge. Note: Be sure to stop the tower fan from running and unplug the power cord before disassembling and cleaning the machine. After cleaning, please completely dry the parts before installing and using, and avoid direct sunlight.
- Page 12 Maintenance Remove the impeller 叶轮 Impeller As shown in the figure, use ⑤ special wrench to rotate counterclockwise to remove the fixing screw at the bottom of the impeller. Push the impeller upward so that it can resist the top of the impeller bin, and then pull it out to disassemble.
- Page 13 Non-washable parts: Tower fan main machine, and power cord Please use a soft dry cloth to gently wipe the tower fan main engine and power cord. Note: Do not clean any components except the rear grille and impeller with water or other liquids.
- Page 14 Troubleshooting 故障现象 Fault 可能原因 Reason 解决方法 Solution 连接符合产品要求的电源 Connect the power 产品未通电 Product is not powered on supply that meets the product requirements 塔扇后格栅安装不到位 The rear grille of 将后栅格安装到位 Installing rear grid in place 塔扇不运转 The the tower fan is not installed properly. tower fan does 塔扇主体与底座安装不到位...