Contents seCtion i General information 1.1 introduction ........................1-1 1.2 Description ........................1-1 1.3 technical Characteristics ....................1-1 1.4 factory options ....................... 1-2 1.5 accessories ........................1-3 1.6 license requirements ....................1-3 1.7 radio Controls ......................... 1-3 1.8 lCD Display ........................1-4 Status Indicators ..........................1-4 Display Options ..........................
Page 3
2.3 radio functions and setup .................... 2-3 radio Controls ..........................2-3 Button Options and Labels ......................2-4 Keypad Menu Operation .......................2-4 Channel/Zone Selection Options ....................2-6 Display options ..........................2-8 Command Zones ..........................2-10 Building a Command Zone [CHAN+] ..................2-10 Editing a Command Zone [CHAN-] .................... 2-11 Code Guard and network access Codes ..................
Page 4
messaging ............................2-22 Text Messaging [TXT] .........................2-22 Short Message Update [MSG] ....................2-23 User Status Messaging [STS] ....................2-23 Paging and Call alert ........................2-25 Conventional Two-Tone/DTMF/MDC1200 Paging [MUTE] ............2-25 Call Alert Paging [ALRT] ......................2-25 Radio Check [RCHK] .........................2-26 radio inhibit/Unihibit ........................2-26 Sending a command ........................26 other radio functions ........................2-27 Backlight [LITE] ..........................2-27 Battery Life [LIFE] ........................2-27...
Page 5
seCtion iii tHeorY of oPeration 3.1 introduction ........................3-1 3.2 equipment Description ....................3-1 3.3 theory of operation ......................3-1 seCtion iV maintenanCe 4.1 introduction ........................4-1 4.2 overhaul ........................... 4-1 4.3 radio test Procedures ....................4-2 seCtion V illUstrateD Parts list 5.1 introduction ........................
Page 6
5.6 front assembly ........................ 5-4 Parts List ............................5-5 Assembly Diagram ...........................5-5 5.7 systems assembly ......................5-7 Parts List ............................5-7 Assembly Diagram ...........................5-7 5.8 system Board ........................5-8 Parts List ............................5-8 Parts Placement ..........................5-25 Schematics ............................5-27 5.9 P150 VHf assembly ....................... 5-49 Parts List ............................5-49 Assembly Drawing .........................5-51 5.10 P150 VHf Board ......................
Page 7
5.15 P800 rf Board sub-assy ..................5-145 Parts List ............................5-145 Assembly Drawing ........................5-147 5.16 P800 rf Board ......................5-149 Parts List ............................5-149 Parts Placement ..........................5-167 Schematics ..........................5-169...
General information 1.1 introDUCtion This manual contains information about the physical, mechanical, and electrical characteristics of the BK Radio KNG Series APCO Project 25 portable digital radios. KNG Portable radios are available in VHF, UHF and 800 MHz models. models...
General information Specification P-150 P-400 P-500 P-800 Frequency Range 136 - 174 MHz 380 - 470 MHz 440 - 520 MHz 763 - 870 MHz Operating Temp. -30° to +60° C -30° to +60° C -30° to +60° C -30° to +60° C Standby Current 120 mA 129 mA...
This equipment must be licensed by the Federal Communications Commission (FCC) before it may be used. Your BK Radio dealer can assist you in filing the appropriate application with the FCC and program each radio with your authorized frequencies and signaling codes.
XD Ch 1 Check with your BK Radio dealer or K N G - P15 0 Programmable alphanumeric labels communications officer for information 171. 5 8 5 0 0 M H z...
Talkgroup identification of a received transmission Group Zone label Programmed Label of Currently Selected Zone Zone number Number of Currently Selected Zone Zone and Channel Currently Selected Zone and Channel Numbers rX/tX Key Encryption key information for the selected channel BK Radio Page 1-5...
Software. The programmed functions are activated by pressing the associated button. Active functions are indicated by a highlighted background. = Active, = Inactive. Side Buttons Collar Switch Right Toggle BK RADIO SCAN SCAN Orange Button Left Toggle Diamond Square Down...
Page 14
Squelch Adjust SQ AD Surveillance Mode SURV System Test Menu Only Item Talkback TKBK Text Message Two-Tone Select TONE Tx Digital TXAD Tx Power Tx Secure (Encrypted models only) Uninhibit UNINH Unit Call UNIT User Status BK Radio Page 1-7...
Site Search 1.10 serViCe information If you need service, contact your local BK Radio dealer equipped to service your radio. If you find it impractical to have service performed by your local dealer, contact BK Radio at the address below:...
All information programmed into the radio is maintained even when the battery pack is removed. BK Radio battery packs are available in a variety of capacities and types for special applications. Rechargeable battery packs can be charged separately or while attached to a radio.
NOTE: Transmitting without an antenna could result in damage to your radio. Use BK Radio approved antennas only. Use of non-qualified or mismatched antennas could result in diminished radio operation. Published radio specifications cannot be guaranteed with non-approved antennas.
2. Talk in a normal voice with the microphone one to two inches from your mouth. 3. Release the PTT switch to stop transmitting. BK RADIO If the length of your message is nearing the programmed Time-Out Timer setting, a tone sounds indicating 5 seconds left to transmit. At the end of the programmed time, the transmitter automatically shuts off and an alert tone sounds.
Editor Software. The programmed functions are activated by pressing the associated button. Active functions are indicated by a highlighted background. = Active, = Inactive. Side Buttons Collar Switch Right Toggle 7 8 9 7 8 9 BK RADIO SCAN SCAN Orange Button Left Toggle Diamond Square Down PQRS...
Page 20
Site Lock**** Site Search**** stsr Squelch Adjust Surveillance Mode sUrV System Test Talkback tKBK Text Message Two-Tone Select tone Tx Digital/Analog tXaD Tx Power Tx Secure** Unihibit UninH Unit Call Unit User Status Version (cont.) BK Radio Page 2-5...
operation and Programming options and labels (cont.) menu switch Button label trunk Conv. mUte Voice Mute Zeroize Keys** Zero Zone Scan ZsCn Zone Scan List ZsC+ Zone Select Zone Emergency button can only be assigned to the orange button. Works on a per-channel basis. *Requires GPS option.
Page 22
Select the desired function from the drop down list. To assign button and switch functions for conventional channels: Select the Global/Trunking/Buttons tab. Point the cursor at the button or switch to be programmed. Select the desired function from the drop down list. menu items BK Radio Page 2-7...
operation and Programming To assign the list of items that are accessed by pressing the “MENU” Button: Select the Global/Conventional/Menus or Global/Trunking/Buttons tab. Select “Main Menu” from the drop box at the upper left of the menu window. Highlight the desired menu items from the “Available” box. Click “>”...
Page 24
Date and time Displays date and time. Dtmf* Displays the numeric DTMF tones of received signal. frequency* Operating frequency of currently selected channel or active scanned channel. mDC* Displays the numeric MDC ID or received signal DTMF. BK Radio Page 2-9...
operation and Programming alPHanUmeriC laBel oPtions radio name Displays radio name. received tGiD P25 Talk Group ID of the radio transmitting the message currently being received. rx’d Unit iD P25 ID of a received digital signal. If the incoming ID is programmed in your Unit ID Call List list, the associated label will be displayed.
NAC. TGIDs and P25 Unit IDs are ignored. Each digital channel is programmed with a receive NAC and a transmit NAC. When an incoming signal’s NAC matches the channel’s programmed receive NAC, the radio unmutes. The default NAC is 0659 ($293 hex). BK Radio Page 2-11...
operation and Programming The digital equivalent of carrier squelch is achieved by programming the receive NAC = $F7E (3966 decimal). The radio will unmute when a digital signal with any NAC is detected. The $F7E (3966 decimal) NAC is reserved for receivers and is not allowed as a transmit NAC. Selective squelch is used for processing Group Calls and Unit-to-Unit Calls.
Once the signal ends, the radio continues to monitor the channel for the preset scan delay time before it resumes scanning. Channel Scan operation can be a switch or as a button or menu list item. Channel Scan may be used in conjunction with Priority Scan operation (see Priority Scan). BK Radio Page 2-13...
operation and Programming scanning Code Guarded Channels Conventional Analog Channels When a signal is detected, scanning stops while the radio checks for the proper Code Guard value. If the signal contains the proper Code Guard value, the radio receives the message. Otherwise, the radio resumes scanning immediately.
Press “ENTER” to open System Priority Channel menu. Options: off - Disables the priority channel. Use main - Uses the selected channel as the priority channel. select - Assigns a specific channel as the priority channel. BK Radio Page 2-15...
operation and Programming To assign a specific channel as a System Priority Channel, highlight “Select” and press the “ENTER” button. The Zone selection menu will be displayed. Highlight the zone of the desired priority channel and press the “ENTER” buttons. The Channel selection menu will then be displayed.
Open the menu of available TGIDs. Select the desired Talk Group ID or, to return the TGID to the pre-programmed value, select “Default”. Press “ENTER” to set the selection. If allowed, picklist values can be changed through keypad programming. BK Radio Page 2-17...
operation and Programming enCrYPtion KeY PiCKlist [KeY] Digital or Mixed Mode Channels Encryption equipped radios only. Selecting an Encryption Key from the Pick List will assign the key to all encrypted channels that do not have ‘Key Lock’ programmed. Locked key channels will continue to use the pre-programmed key.
P25 ID or MDC number or label will be displayed during the U n i t I D 12 3 4 5 reception. An alert tone will be emitted if the radio is programmed to do so. The lite menU RXD icon will also be lit. BK Radio Page 2-19...
Radios that have the DES/AES factory option for encryption must have encryption keys loaded with an APCO Project 25 compatible key fill device such as the Motorola KVL 3000 Plus, using a BK Radio keyloader cable. The radio can hold up to 64 AES and/or DES keys.
Zeroize can be assigned as a button or menu list item. Open the “Zeroize Keys” menu. Press “YES” to erase all encryption keys or “ESC” to cancel the action. When successfully removed the “Keys Removed” message will momentarily be displayed. BK Radio Page 2-21...
operation and Programming messaGinG Digital Conventional P25 channels can be programmed to send and receive text messages and radio status messages. Text messages can be selected from a pre-programmed list or manually entered using the radio keypad. Status messages are pre-programmed only. text messaging [tXt] Conventional Digital Channels Message types include predefined messages, manually entered messages or locally stored...
ID “Status: Status X” is displayed, where “X” is the received ID number. 1. select status message Press the “STS” button or select “Status Update” from the menu. From the “Select Status” menu, select the programmed message to send and press “Enter”. BK Radio Page 2-23...
Page 39
operation and Programming 2. select message type From the “Select Target Type” select the type of message to be sent. Unit - Send the message to an individual radio ID. Group - Send message to a group of radios using the Talk Group ID. Dispatch - Send the message to a dispatch console.
When a Call Alert is received, an alert tone will sound and the incoming unit ID or alias is displayed for approximately 5 seconds. The top display line line will alternated between the programmed display information and a Call Alert Received message until. Select “Call Alert” to reset. BK Radio Page 2-25...
operation and Programming radio Check [rCHK] Conventional Digital Channels The KNG can be programmed to check the availability of a KNG radio with a specific P25 ID. requesting a radio Check Press the “RCHK” button or open “Radio Check” from the menu. Select Target Radio last Call Select “Last Call”...
- This setting will display “Busy” momentarily and an alert tone will sound. The radio will then revert back to receive mode and monitor the active receive traffic. (carrier mode only) BK Radio Page 2-27...
Cloning [Clon] Conventional Zones KNG radios can be set up to send or receive programmed information from other BK Radio products via a cloning cable available from BK Technologies. Cloning can be assigned to a button. Refer to the cloning cable manual for cloning information.
Must be configured as “Customizable” in the PC Radio Editor to access through the radio. When pressed, changes the volume level at lower volumes. This allows the user to set their minimum volume to an audible level. BK Radio Page 2-29...
operation and Programming monitor Conventional Channels There are three settings available for monitoring traffic on a selected channel. “Monitor” can be assigned to a button or as a menu item. monitor modes and indicators Off - Squelch works as configured. (No indicator) On - Only carrier squelch is in effect.
[sUr] Conventional and Trunking Channels When Surveillance Mode is on, all audible indicators (beeps etc.) and lighting functions (LEDs and Display) are disabled. Surveillance Mode can a switch, button or as a menu list item. BK Radio Page 2-31...
operation and Programming system test Conventional and Trunking Channels The KNG portable offers a variety of system tests when connected to the appropriate test equipment. Select the appropriate test and follow the onscreen prompts. transmit Digital [tXD/a] Conventional Mixed-Mode Transmit Channels When Transmit Digital is on, channels programmed for mixed-mode transmit will transmit in digital mode.
Keypad programmable categories include individual Channel, Zone and Global radio parameters, individual P25 ID Quick Call/Receive List, User Tone List, User NAC List and User Talk Group ID List. Check with your BK Radio dealer or communications officer for information on the programmed functions of your radio.
operation and Programming entering Keypad Programming mode To enter programming mode open the menu list by pressing the assigned “Menu” button and select “Keypad Prog” from the menu list. Use the keypad to enter the six-digit user or master password and press the Enter button. Select the item to program and press Enter.
To designate a specific priority channel choose “Select” from the priority channel menu. Select the Zone and Channel. tx on Priority 1 Channel If on, the radio will transmit on the System Priority 1 channel whenever Priority Scan is on. BK Radio Page 2-35...
operation and Programming Zone settinGs To edit the programmable Zone settings, select “Keypad” from the programing menu then select “Zone” from the sub-menu. Select Add, Delete or Edit Zone from the Zone menu. add Zone When selected, a new zone is added in the next available slot. Example: If there are seven zones in the radio, the added zone will be zone eight.
Page 52
- 25kHz spacing when operating in analog. tx Power low Power - Lock channel in low power mode. High Power - Lock channel in high power mode. selectable - Allow high/low transmit power selection form assigned button, switch or menu item. BK Radio Page 2-37...
operation and Programming tx frequency Enter a valid receive frequency in MHz. Frequencies must be divisible by 1.25kHz. tx mode Select Analog, Digital or Selectable. tx Guard Analog or Mixed Mode Receive Channels Only Select “Off” for analog signals to operate in carrier squelch mode. Select “Tone”...
Select “User TGIDs” from the programing menu. Select the Talk Group ID to edit. Enter the desired value (1 - 65535). NOTE: A Talk Group ID value of 0 is not allowed. BK Radio Page 2-39...
operation and Programming KeYPaD ProGramminG CHaraCters P, Q, R, S, p, q, r, s, 7 PQRS A, B, C, a, b, c, 2 T, U, V, t, u, v, 8 D, E, F, d, e, f, 3 W, X, Y, Z, w, x, y, z, 9 WXYZ G, H, I, g, h, i, 4 0, Blank Space...
3.1 introDUCtion This section contains a description of equipment and a theory of operation for the BK Radio KNG Series APCO Project 25 digital radio. To aid in understanding the operation of the equipment, schematic diagrams are found in Section 5 of this manual.
Page 57
theory of operation Core microprocessor The core microprocessor communicates with the baseband signal processor, the LCD display and the battery. It controls radio functions such as adjusting the deviation and receiver tuning. The microprocessor communicates with the EEPROM on the RF board to access the stored calibration and tuning data that is unique to each radio.
Page 58
The Synthesizer section has circuits that perform many functions including frequency generation, modulation and buffering. The main functional blocks in the transmitter are: • TCXO frequency reference • Synthesizer IC • Loop Filter • Rx VCO • Tx VCO • Digital Potentiometer • VCO Buffer BK Radio Page 3-3...
Page 59
theory of operation Programming Coarse Tune TCXO Reference Rx VCO Loop Filter 10 MHz VCO Buffer Steering Line Synthesizer Tx VCO Tx / Rx Tx / Rx Coarse Tune Tx Audio Coarse Tune RX VCO TX VCO 181-219 MHz (P150) 136-174 MHz (P150) Digital From uP...
Page 60
RF signals to flow to the Receiver with the Transmitter output port removed from the circuit. The Harmonic Filter attenuates the harmonics created by the Power Amplifier to meet or exceed the transmit spurious and harmonic specification. The passband input and output impedances of the filter are 50 Ohms. BK Radio Page 3-5...
Page 61
theory of operation receiver The receiver section consists of many circuits which perform a variety of tasks including filtering, impedance matching, mixing, and analog-to-digital conversion. The main blocks of the receiver are: • Tunable Preselector • Low Noise Preamplifier • Fixed Image Rejection Filter (VHF Models) •...
Page 62
The bits are then formatted and stored in a buffer in preparation for transfer via the SSI to the radio’s microprocessor. Ultimately, the sampled data is transferred to the microprocessor at 19.2 k samples per second with 16 bits of data per sample. BK Radio Page 3-7...
Page 63
theory of operation Page 3-8 Service Manual - KNG Portables...
1. Disconnect the flex circuits connecting the Systems Board to the side connector and display assembly. 2. Disconnect the speaker. 3. Remove the two screws holding the Systems board to the housing. 4. Lift the board from the top to remove. BK Radio Page 4-1...
maintenance sHielDs Most shield on the KNG are press on type and can be removed by gently prying the lid. Some require unsoldering before removal. CleaninG Using a clean, lint-free cloth, lightly moistened with soap and water only, and remove the foreign matter from the equipment case and unit front panel.
Page 66
MODULATION RADIO COUNTER METER COMMUNICATIONS TEST SET (SERVICE MONITOR) AUDIO 50 OHM RF IN LOAD RF POWER METER TEST AUDIO GENERATOR OPTIONAL 10 VDC ANTENNA MIC. AUDIO REGULATED POWER SUPPLY RADIO figure 4-2 transmitter tests setup BK Radio Page 4-3...
Page 67
maintenance OPTIONAL RADIO COMMUNICATIONS AUDIO TONE TEST SET GENERATOR GENERATOR (SERVICE MONITOR) AUDIO IN RF OUT SINAD SIGNAL GENERATOR OPTIONAL SINAD METER TEST DISTORTION ANALYZER 10 VDC ANTENNA EXT. SPEAKER REGULATED POWER SUPPLY RADIO figure 4-3 receiver tests setup Page 4-4 Service Manual - KNG Portables...
Parts list 5.1 introDUCtion This section helps you identify parts used in BK Radio’s KNG Portable radios. It includes Replacement Parts Lists for all major assemblies arranged from the Final Assembly down to an individual part level. Each List is followed by the corresponding Assembly Drawing (if required), Schematic Diagram and Parts Placement.
2 Items 6 & 7 Must be soldered to the their respective fences. 3. Item 5 must be installed before installing Item 4 to the connector. 4. Item 5 must be properly aligned to the board-to-board connector to avoid damage to the board during installation. BK Radio Page 5-7...
Page 85
illustrated Parts lists Parts List, System Board, OMAP_SMD,KNG Portable reference Part number Description notes 4734-01003-311 Res,CP,100K,1%,1/16W,0402 4734-05902-311 Res,CP,59K,1%,1/16W,0402 4734-01002-311 Res,CP,10K,1%,1/16W,0402 4735-20101-231 Res,Cp,8 X 100_Ohms,Ntwrk,5%,1/16W 4734-01003-311 Res,CP,100K,1%,1/16W,0402 4735-20101-231 Res,Cp,8 X 100_Ohms,Ntwrk,5%,1/16W 4734-04422-311 Res,Cp,44.2K,1%,1/16W,0402 4734-01272-311 Res,Cp,12.7K,1%,1/16W,0402 4735-20102-231 Res,Cp,8 X 1K Ntwrk,5%,1/16W 4735-20101-231 Res,Cp,8 X 100_Ohms,Ntwrk,5%,1/16W 4735-20102-231 Res,Cp,8 X 1K Ntwrk,5%,1/16W...
Page 92
KNG-Portable Systems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 1 of 1 Rev. D PRODUCTS WITHOUT PERMISSION BK Radio Page 5-25...
Page 93
systems Board illustrated Parts list BLANK PAGE Page 5-26 Service Manual - KNG Portables...
Page 94
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED Sheet 1 of 11 Rev. G AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION BK Radio Page 5-27...
Page 95
systems Board illustrated Parts list BLANK PAGE Page 5-28 Service Manual - KNG Portables...
Page 96
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 2 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-29...
Page 97
systems Board illustrated Parts list BLANK PAGE Page 5-30 Service Manual - KNG Portables...
Page 98
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 3 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-31...
Page 99
systems Board illustrated Parts list BLANK PAGE Page 5-32 Service Manual - KNG Portables...
Page 100
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 4 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-33...
Page 101
systems Board illustrated Parts list BLANK PAGE Page 5-34 Service Manual - KNG Portables...
Page 102
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 5 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-35...
Page 103
systems Board illustrated Parts list BLANK PAGE Page 5-36 Service Manual - KNG Portables...
Page 104
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 6 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-37...
Page 105
systems Board illustrated Parts list BLANK PAGE Page 5-38 Service Manual - KNG Portables...
Page 106
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 7 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-39...
Page 107
systems Board illustrated Parts list BLANK PAGE Page 5-40 Service Manual - KNG Portables...
Page 108
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 8 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-41...
Page 109
systems Board illustrated Parts list BLANK PAGE Page 5-42 Service Manual - KNG Portables...
Page 110
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 9 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-43...
Page 111
systems Board illustrated Parts list BLANK PAGE Page 5-44 Service Manual - KNG Portables...
Page 112
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 10 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-45...
Page 113
systems Board illustrated Parts list BLANK PAGE Page 5-46 Service Manual - KNG Portables...
Page 114
KNG-P Sytems Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 11 of 11 Rev. G PRODUCTS WITHOUT PERMISSION BK Radio Page 5-47...
Page 115
systems Board illustrated Parts list BLANK PAGE Page 5-48 Service Manual - KNG Portables...
Page 117
Page 5-50 Service Manual - KNG Portables...
Page 118
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED KNG-P150 VHF Bd Assy AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. H BK Radio Page 5-51...
Page 119
KnG P150 VHf Board illustrated Parts list BLANK PAGE Page 5-52 Service Manual - KNG Portables...
Page 136
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. F11 BK Radio Page 5-69...
Page 137
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-70 Service Manual - KNG Portables...
Page 138
P-150 VHf Board 3333-30976-500 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 5 BK Radio Page 5-71...
Page 139
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-72 Service Manual - KNG Portables...
Page 140
P-150 VHf Board 3333-30976-500 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 2 of 5 BK Radio Page 5-73...
Page 141
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-74 Service Manual - KNG Portables...
Page 142
P-150 VHf Board 3333-30976-500 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 3 of 5 BK Radio Page 5-75...
Page 143
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-76 Service Manual - KNG Portables...
Page 144
P-150 VHf Board 3333-30976-500 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 4 of 5 BK Radio Page 5-77...
Page 145
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-78 Service Manual - KNG Portables...
Page 146
P-150 VHf Board 3333-30976-500 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P150 VHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 5 of 5 BK Radio Page 5-79...
Page 147
P-150 VHf Board illustrated Parts list BLANK PAGE Page 5-80 Service Manual - KNG Portables...
Page 149
P400 UHf Board illustrated Parts list Page 5-82 Service Manual - KNG Portables...
Page 150
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED KNG-P400 UHF Bd Assy AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. F BK Radio Page 5-83...
Page 151
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-84 Service Manual - KNG Portables...
Page 167
illustrated Parts lists Parts List, UHF Board, KNG-P400 reference Part number Description notes 2508-30987-500 Shield-Fence,Top,Mixer 2508-30987-400 Shield-Fence,Bottom,Mixer 2508-30987-200 Shield-Fence,Top, IF 2508-30987-100 Shield-Fence,Bottom, IF 2508-30987-800 Shield-Fence,Top, Synth 2508-30987-700 Shield-Fence,Bottom, Synth 2508-30988-100 Shield-Fence,Top,VCO SH10 2508-30988-000 Shield-Fence,Bottom,VCO 3134-30906-203 IC,RF_SW,SPDT,MFET,PE4259,SC-70 3134-30670-622 IC,IF,Digit,Subsys,AD9864BCPZ,CP-48 3134-30911-003 IC,OP_AMP,R/R, LT1783CS5, SOT-23 3134-30950-304 IC,REG,ADJ,LDO,100ma,TPS79101DBV,SOT-23 3134-30911-003...
Page 168
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. G8 BK Radio Page 5-101...
Page 169
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-102 Service Manual - KNG Portables...
Page 170
KnG-P400 UHf Board 3333-30976-600 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 5 BK Radio Page 5-103...
Page 171
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-104 Service Manual - KNG Portables...
Page 172
KnG-P400 UHf Board 3333-30976-600 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 2 of 5 BK Radio Page 5-105...
Page 173
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-106 Service Manual - KNG Portables...
Page 174
KnG-P400 UHf Board 3333-30976-600 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 3 of 5 BK Radio Page 5-107...
Page 175
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-108 Service Manual - KNG Portables...
Page 176
KnG-P400 UHf Board 3333-30976-600 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 4 of 5 BK Radio Page 5-109...
Page 177
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-110 Service Manual - KNG Portables...
Page 178
KnG-P400 UHf Board 3333-30976-600 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P400 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 5 of 5 BK Radio Page 5-111...
Page 179
KnG-P400 UHf Board illustrated Parts list BLANK PAGE Page 5-112 Service Manual - KNG Portables...
Page 181
P500 UHf Board illustrated Parts list Page 5-114 Service Manual - KNG Portables...
Page 182
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED KNG-P500 UHF Bd Assy AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. H BK Radio Page 5-115...
Page 183
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-116 Service Manual - KNG Portables...
Page 199
illustrated Parts lists Parts List, UHF Board, KNG-P500 reference Part number Description notes 2508-30987-500 Shield-Fence,Top,Mixer 2508-30987-400 Shield-Fence,Bottom,Mixer 2508-30987-200 Shield-Fence,Top, IF 2508-30987-100 Shield-Fence,Bottom, IF 2508-30987-800 Shield-Fence,Top, Synth 2508-30987-700 Shield-Fence,Bottom, Synth 2508-30988-100 Shield-Fence,Top,VCO SH10 2508-30988-000 Shield-Fence,Bottom,VCO 3134-30906-203 IC,RF_SW,SPDT,MFET,PE4259,SC-70 3134-30670-622 IC,IF,Digit,Subsys,AD9864BCPZ,CP-48 3134-30911-003 IC,OP_AMP,R/R, LT1783CS5, SOT-23 3134-30950-304 IC,REG,ADJ,LDO,100ma,TPS79101DBV,SOT-23 3134-30911-003...
Page 200
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P500 UHF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. G8 BK Radio Page 5-133...
Page 201
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-134 Service Manual - KNG Portables...
Page 202
KNG-P500 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 1 of 5 Rev. I PRODUCTS WITHOUT PERMISSION BK Radio Page 5-135...
Page 203
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-136 Service Manual - KNG Portables...
Page 204
KNG-P500 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 2 of 5 Rev. I PRODUCTS WITHOUT PERMISSION BK Radio Page 5-137...
Page 205
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-138 Service Manual - KNG Portables...
Page 206
KNG-P500 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 3 of 5 Rev. I PRODUCTS WITHOUT PERMISSION BK Radio Page 5-139...
Page 207
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-140 Service Manual - KNG Portables...
Page 208
KNG-P500 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 4 of 5 Rev. I PRODUCTS WITHOUT PERMISSION BK Radio Page 5-141...
Page 209
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-142 Service Manual - KNG Portables...
Page 210
KNG-P500 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF Sheet 5 of 5 Rev. I PRODUCTS WITHOUT PERMISSION BK Radio Page 5-143...
Page 211
KnG-P500 UHf Board illustrated Parts list BLANK PAGE Page 5-144 Service Manual - KNG Portables...
Page 212
5400-31022-000 Heatsink-Spacer, PA, KNG-P800 1400-31034-700 Brace, PTT-Switch, KNG-P 2508-31045-000 Shield, PA, KNG-P800 2813-31044-900 Standoff, SS, 4mm, Hex, M2 x .4 Thread QTY: 2 2820-30603-038 Screw-Metric, Machine, M2 x .4 x 2, PH, T, SS QTY: 2 BK Radio Page 5-145...
Page 213
P800 rf Board illustrated Parts list Page 5-146 Service Manual - KNG Portables...
Page 214
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED KNG-P800 RF Bd Assy AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. C BK Radio Page 5-147...
Page 215
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-148 Service Manual - KNG Portables...
Page 234
THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RF Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 1 Rev. B10 BK Radio Page 5-167...
Page 235
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-168 Service Manual - KNG Portables...
Page 236
KnG-P800 rf 3333-30976-700 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RT Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 1 of 6 BK Radio Page 5-169...
Page 237
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-170 Service Manual - KNG Portables...
Page 238
KnG-P800 rf 3333-30976-700 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RT Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 2 of 6 BK Radio Page 5-171...
Page 239
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-172 Service Manual - KNG Portables...
Page 240
KnG-P800 rf 3333-30976-700 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RT Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 3 of 6 BK Radio Page 5-173...
Page 241
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-174 Service Manual - KNG Portables...
Page 242
KnG-P800 rf 3333-30976-700 KNG-P800 RT Board THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES AND SHALL NOT BE REPRODUCED, COPIED OR USED Sheet 4 of 6 AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION BK Radio Page 5-175...
Page 243
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-176 Service Manual - KNG Portables...
Page 244
KnG-P800 rf 3333-30976-700 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RT Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 5 of 6 BK Radio Page 5-177...
Page 245
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-178 Service Manual - KNG Portables...
Page 246
KnG-P800 rf 3333-30976-700 THIS DRAWING IS PROPERTY OF BK TECHNOLOGIES KNG-P800 RT Board AND SHALL NOT BE REPRODUCED, COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF PRODUCTS WITHOUT PERMISSION Sheet 6 of 6 BK Radio Page 5-179...
Page 247
KnG-P800 rf Board illustrated Parts list BLANK PAGE Page 5-180 Service Manual - KNG Portables...
Need help?
Do you have a question about the KNG Series and is the answer not in the manual?
Questions and answers