Table of Contents
Advertisement
Quick Links
HDE51C
BATTERY POWERED CRIMP TOOL
Description
The HDE51C Battery Powered Crimp Tool is a hand held,
self contained crimp tool intended to crimp copper and
aluminum cable with DMC HD51 dies.
Safety
Safety is essential in the use and maintenance of DMC
tools and equipment. This manual and any markings on
the tool provide information for avoiding hazards and
unsafe practices related to the use of this tool. Observe all
of the safety information provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with the
safe operation and maintenance procedures for the
following DMC tool:
HDE51C Battery Powered Crimp Tool
Keep this manual available to all personnel. Replacement
manuals are available upon request at no charge.
All specifications are nominal and may change as
design improvements occur. DMC shall not be liable
for damages resulting from misapplication or misuse
of its products.
HDE51C-DS
©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED
Daniels Manufacturing Corporation
526 Thorpe Road, Orlando, FL 32824 USA
Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com
K EEP THI S M ANUAL
Important Safety Information
Page 1 of 8
REV. A
DATASHEET
7/26/2022
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DMC HDE51C
Summary of Contents for DMC HDE51C
- Page 1 BATTERY POWERED CRIMP TOOL DATASHEET K EEP THI S M ANUAL Description The HDE51C Battery Powered Crimp Tool is a hand held, Important Safety Information self contained crimp tool intended to crimp copper and aluminum cable with DMC HD51 dies.
- Page 2 DO NOT REM OVE TOOL HEAD DO NOT OPERATE TOOL WITHOUT HEAD INSTALLED HDE51C-DS ©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED Page 2 of 8 REV. A 7/26/2022 Daniels Manufacturing Corporation 526 Thorpe Road, Orlando, FL 32824 USA Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com...
-
Page 3: Important Safety Information
Charging Voltage=18 VDC Charging Time=22 minutes US Pat. No. 7,254,982 HDE51C-DS ©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED Page 3 of 8 REV. A 7/26/2022 Daniels Manufacturing Corporation 526 Thorpe Road, Orlando, FL 32824 USA Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com... -
Page 4: Operation
2. Slide the die into the crimping head until it Annually or after 10,000 Crimps “snaps” into place. 1. Return the tool to the DMC repair center for 3. Properly position the second die, and repeat step 2. inspection & calibration. -
Page 5: Troubleshooting
HDE51C-DS ©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED Page 5 of 8 REV. A 7/26/2022 Daniels Manufacturing Corporation 526 Thorpe Road, Orlando, FL 32824 USA Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com... -
Page 6: Charging A Battery
120 VAC Power Adapter HDE-120AC-A 230 VAC Power Adapter HDE-230AC-A HDE51C-DS ©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED Page 6 of 8 REV. A 7/26/2022 Daniels Manufacturing Corporation 526 Thorpe Road, Orlando, FL 32824 USA Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com... -
Page 7: Data Sheet
Pressing and holding both button lets you HDE51C-DS ©2022 DANIELS MANUFACTURING CORP., ALL RIGHTS RESERVED Page 7 of 8 REV. A 7/26/2022 Daniels Manufacturing Corporation 526 Thorpe Road, Orlando, FL 32824 USA Phone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com... -
Page 8: Error Codes
(90) days after delivery to the first user, provided that the product is returned to DMC with all transportation charges prepaid and which shall appear to DMC’s satisfaction, after DMC’s inspection, to have been defective in material and workmanship, it being understood that DMC products are not consumer products.
Need help?
Do you have a question about the HDE51C and is the answer not in the manual?
Questions and answers