Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tenda HG6
Summary of Contents for Tenda HG6
- Page 1 Quick Installation Guide N300 Wi-Fi xPON ONT Package Contents • xPON ONT x 1 • Power adapter x 1 • Ethernet cable (RJ45) x 1 • Telephone cable (RJ11) x 1 • User manual x 1 For product or function details, please go to www.tendacn.com to download the user guide.
-
Page 2: Get To Know The Ont
Get to know the ONT LED indicators LED indicator Color Status Description Solid on The ONT is powered on properly. Green The ONT is powered off or not powered on properly. Solid on The ONT is registered successfully. Green Blinking The registration is not completed (unregistered or registering). -
Page 3: Ports And Buttons
Ports & Buttons RESET WLAN ON/OFF LAN4 LAN3 LAN2 LAN1 Port/Button Description Power on/off button. ON/OFF Press the button to turn on or off the ONT. Optical fiber port. Used to connect to a fiber cord. Power jack. Please use the included power adapter to connect the ONT to a power source. USB 2.0 port. - Page 4 1. Connect and register the ONT Caution, laser DO NOT look directly at the PON port when the device is powered on, as well as the terminal of the indoor fiber cord, to prevent any harm to your eyes. Connect the ONT as shown in the figure. Wait until the PON LED indicator lights solid on, then the ONT is registered successfully.
-
Page 5: Router Mode
2. Configure the internet access Tips: Choose a desired mode to configure your internet access: Router mode: Choose this mode if your internet access type is PPPoE or DHCP. Bridge mode (default): Choose this mode if your internet access type is PPPoE. Router mode Option 1 Access internet over PPPoE Step 1: Log in to the web UI... - Page 6 PON WAN This page is used to configure the parameters for PONWAN nas0_0 Enable VLAN: VLAN ID: 802.1p_Mark Multicast Vlan ID: [1-4094] Channel Mode: PPPoE Admin Status: Enable Disable Connection Type: INTERNET MTU: 1492 Enable IGMP-Proxy: Enable MLD-Proxy: IP Protocol: IPv4 PPP Settings: UserName:...
- Page 7 Option 2 Access internet over DHCP Step 1: Log in to the web UI Refer to Step 1: Log in to the web UI in Option 1 Access internet over PPPoE to log in to the web UI of the ONT. Step 2: Set up a WAN connection Choose WAN >...
- Page 8 Done. To access the internet: Connect your wired device, such as a computer, to a LAN port of the ONT. Connect your wireless device, such as a smartphone, to the Wi-Fi network of the ONT, using the SSID (Wi-Fi name) and Key (Wi-Fi password) on the bottom label. Tips: If you cannot access the internet after the configuration, refer to Q2 in FAQ.
-
Page 9: Bridge Mode
Bridge mode Tips: When the ONT is set to Bridge mode, please configure internet settings based on ISP requirements. Access internet over PPPoE Connect a LAN port of the ONT to the WAN port of the router using an Ethernet cable. Connect the computer to a LAN port of the router using an Ethernet cable. - Page 10 Q1: I cannot log in to the web UI by visiting 192.168.1.1. What should I do? A1: Try the following solutions: Ensure that the ONT is powered on properly (the PWR LED indicator is solid green). If you use a wireless device, such as a smartphone, to configure the ONT: - Ensure that your smartphone has disabled mobile data and is connected to the Wi-Fi network of the ONT.
- Page 11 Q4: How to reset the ONT? A4: Method1: After the ONT completes startup, use an object with a spike to hold down the RESET button for 10 or more seconds and release it. All LED indicators light off in a few seconds. When the PWR LED indicator lights solid on again, the ONT is reset.
- Page 12 Copyright © 2021 Shenzhen Tenda Technology Co., Ltd. All rights reserved. Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice.