Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vendors Exchange CURVE AP 113
Summary of Contents for Vendors Exchange CURVE AP 113
- Page 1 CURVE™ Door AP 113, AP 123, AP 7000 AP 113, AP 123, AP 7000 - PLATINUM AP 113, AP 123, AP 7000 - BLACK www.veii.com 8700 BROOKPARK ROAD 1.800.321.2311 CLEVELAND, OHIO 44129 VE1015205, REV B. ©2021, VENDORS EXCHANGE® INTERNATIONAL, USA...
-
Page 2: Table Of Contents
INSTALLATION GUIDE TABLE OF CONTENTS To navigate this installation guide: Click or touch each chapter title above to go directly to that section or pages and it will take you immediately to that page via a hyperlink. Any pages with italicized words are links to other sections and pages and by clicking or touching those links will also take you back and forth within this installation guide. -
Page 3: Precautionary Symbols
INSTALLATION GUIDE PRECAUTIONARY SYMBOLS WHAT THE SYMBOLS MEAN WARNING, CAUTION, and NOTICE statements are used in this installation manual to stress important and critical information to safely service this door. These statements, according to the American National Standards (ANSI), are described below. WARNING THIS SYMBOL INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY. -
Page 4: Tools Needed
INSTALLATION GUIDE TOOLS NEEDED TOOLS TO USE FOR PROCEDURES IN THIS MANUAL 5/32” HEX KEY 7/16” BOX PHILLIPS FLAT HEAD 11/32” NUT 5/16” NUT STANDARD SIDE/WIRE (ALLEN WRENCH SCREW- SCREW- DRIVER DRIVER SOCKET SET CUTTERS WRENCH) DRIVER DRIVER FLASHLIGHT CORDLESS DRILL WITH 1/4” SOCKET CRESCENT WRENCH SOME IMAGES USED IN THIS MANUAL ARE FOR ILLUSTRATIVE PURPOSES... -
Page 5: Service Kits − Curve Door
INSTALLATION GUIDE SERVICE KITS − CURVE DOOR PART NUMBER DESCRIPTION QTY. VE1581 ITEM TABS VE4653K 1/2 IN. BLACK NYLON CABLE CLAMP VE4650K 4 - WAY TIE MOUNT VE4601K 6 IN. WHITE CABLE TIE VE4849 ENERGY SAVING LED CLING - ON LABEL VE5800 UCB PROGRAMMING INSTRUCTION GUIDE VE5876... -
Page 6: Service Parts − Drop Sensor
INSTALLATION GUIDE SERVICE PARTS − DROP SENSOR PART NUMBER DESCRIPTION VE6886 ADA DROP SENSOR TRANSMITTER (BUCKET LINKAGE SIDE) VE6887 ADA DROP SENSOR RECEIVER (HINGE SIDE) SERVICE PARTS − LABELS PART NUMBER DESCRIPTION VE1581 ITEM TABS − NUMBERS 110 − 189 VE673 (SERIES) PRICE LABELS (SPECIFY PRICES) VE5876... -
Page 7: Service Parts − Ucb
INSTALLATION GUIDE SERVICE PARTS − UCB™ PART NUMBER DESCRIPTION VE5801 UNIVERSAL CONTROL BOARD VE5816 MDB HARNESS VE5853D DISPLAY HARNESS VE5861DF HARNESS BOARD FORCED VE5862 DISPLAY BOARD VE6820 DEX HARNESS SERVICE PARTS − DOOR PART NUMBER DESCRIPTION VE1529 DOOR SWITCH VED3567 LOCK BAR VED3562 KEY PAD... -
Page 8: Service Parts − Motors
INSTALLATION GUIDE SERVICE PARTS − MOTORS PART NUMBER DESCRIPTION VE2995 SINGLE SPIRAL VEND MOTOR (AP 113, AP 7000) VE8317 DUAL SPIRAL VEND MOTOR (AP 113, AP 7000) VE8322 SINGLE SPIRAL VEND MOTOR (AP 123) VE8320 DUAL SPIRAL VEND MOTOR (AP 123) SERVICE PARTS −... - Page 9 INSTALLATION GUIDE CURVE™ Door AP 113, AP 123, AP 7000 To TOC Overview...
-
Page 10: Door Overview − Oem Door
INSTALLATION GUIDE DOOR OVERVIEW − OEM DOOR All Descriptions Linked to Sections in this Manual Highlight the Text, Then Click with Your Mouse or Finger Inside Location of Top Hinge Location of Touch Pad, Lens and Mounting Plate Display and Display Board and Machine Switch Inside Location of Bottom Inside Location of Card... -
Page 11: Door Overview − Curve Door
INSTALLATION GUIDE DOOR OVERVIEW − CURVE DOOR All Descriptions Linked to Sections in this Manual Highlight the Text, Then Click with Your Mouse or Finger Inside Location of UCB Board Inside Location of Top Hinge and Mounting Plate Inside Location of Delivery Inside Location of Card Validator Bucket and Harnesses and Door Switch. -
Page 12: Remove Oem Door, Prepare For Curve Door
INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR NOTICE WARNING WARNING CAUTION TEST THE MACHINE TO PREVENT DO NOT REMOVE TO AVOID POTENTIAL THAT IT IS IN PERSONAL INJURY THE TRAYS FROM INJURY, IT IS HIGHLY WORKING ORDER AND EQUIPMENT THE CABINET. - Page 13 INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR Then, for AP 7000, AP 113, and AP 123, unplug all harnesses from existing controller circuit board. The AP 113 (A) and AP 7000 (B) are shown here as examples. AP 113 AP 7000 Next, if present, remove the validator (A) and coin mech (B).
- Page 14 INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR Then, if a gum and mint tray are available, remove it from the cabinet by sliding the plate forward and unfastening (4) Screw Locations screws from under the tray. Gum and Mint Tray AP 7000 VARIATION First, using a Phillips screwdriver or the cordless drill with a Phillips Head driver, remove the gum and mint...
- Page 15 INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR AP 7000 VARIATION Then, loosen (2) screws on gum and mint tray slide from both sides of the cabinet. Screws Gum and Mint Tray Slide Next, loosen screw from gum and mint deflector plate as shown.
- Page 16 INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR Housing NOTE: The AP 7000 does not have a ballast filler panel like the AP 113 and AP 123. Bolt Ballast Filler Panel Then, remove cabinet main harness from OEM door and if present, disconnect the ground wire.
- Page 17 INSTALLATION GUIDE REMOVE OEM DOOR, PREPARE FOR CURVE DOOR For AP 113 and AP 123, loosen the top screw only of the ballast filler panel on the inside of the machine to access top bracket fastener. Ballast Filler Panel AP 113, AP 123 Then, for the AP 113, and AP 123 from inside the machine cabinet, loosen all the inner panel screws (see arrows) and set aside for “Install Curve Door”,...
-
Page 18: Install The Curve Door
INSTALLATION GUIDE INSTALLATION GUIDE INSTALL THE CURVE DOOR First, remove the original bottom bracket and install new Bottom Hinge Plate in the same location as shown in image on (Step 1, Page 19, Image Ensure Angle of Hinge Mount Hold to 90 for Proper Open/ Close of Door OEM Hinge... - Page 19 INSTALLATION GUIDE INSTALL THE CURVE DOOR First, align (3) 1/2” Brass Wash- ers (VE8718A) over the hole in the bottom bracket (A), then in- sert the pin from the bottom hinge Bottom Hinge plate attached to the underside of the CURVE Door through the Bracket Hole brass washers into the hole in the bottom bracket (B).
- Page 20 INSTALLATION GUIDE INSTALL THE CURVE DOOR Next, attach the door stop arm to inside stud closest to the inner door frame (see arrow) and Closest Stud turn 1-1/2 turns from tight. Inner Door Frame Then, for AP 113, and AP 123, tighten top screw of ballast filler panel (see arrow).
-
Page 21: Route And Connect Harnesses
INSTALLATION GUIDE INSTALLATION GUIDE ROUTE AND CONNECT HARNESSES AP 113, AP 123 Left Side of the Cabinet Left Side of the Cabinet Ground Wire For AP 113, and AP 123, first, using a Self-Tapping Screw Then, wind the green ground wire around main door harness (VE7373K) or Cable Tie (VE4601K) and 4−Way Mount about 6 to 8 times. - Page 22 INSTALLATION GUIDE ROUTE AND CONNECT HARNESSES Then, for AP 113, connect power harness to main door harness (Image A). Use Cable Tie (VE4601K) to secure both harnesses together and then cut excess away from cable tie (Image B). Cable Tie AP 113 Then, for AP 123, connect power harness to main door harness (left...
- Page 23 INSTALLATION GUIDE ROUTE AND CONNECT HARNESSES AP 7000 VARIATION Pull the new door main harness through the hole Main Door Harness near the power switch as shown. Male pin from the connector may need to be removed to route it through the hole.
-
Page 24: Install The Vend Bucket
INSTALLATION GUIDE INSTALL THE VEND BUCKET NOTICE IT IS RECOMMENDED TO INSTALL THE VEND BUCKET IS COMPLETED WITH AN ADDITIONAL PERSON TO ASSIST WITH POSITIONING AND ALIGNMENT OF THE BUCKET TO PREVENT IMPROPER DOOR ASSEMBLY AND DAMAGE TO THE BUCKET. First, remove the cash box from the door (image A). - Page 25 INSTALLATION GUIDE INSTALL THE VEND BUCKET NOTICE TO FACILITATE POSITIONING AND ALIGNMENT, ONE PERSON SHOULD HOLD THE VEND BUCKET FROM INSIDE THE MACHINE TO ALIGN WITH THE MOUNTING HOLES. THE SECOND PERSON ON THE OTHER SIDE OF THE MACHINE SHOULD ENSURE THAT THE VEND BUCKET ALIGNS PROPERLY IN THE OPENING Door Push Vend Bucket Flap...
- Page 26 INSTALLATION GUIDE INSTALLATION GUIDE INSTALL THE VEND BUCKET Use existing cable clamp on the vend bucket linkage to secure drop sensor cable. Route drop sensor cable as shown in left image (A). Continue routing drop sensor harness toward drop sensor connection. Run harness under spring and secure in existing cable clamp.
- Page 27 INSTALLATION GUIDE INSTALL THE VEND BUCKET Next, apply Item Tabs (VE1581) to the CURVE door trays if equipped with the 7th Tray™ option. Finally, remove the protective coating from the front vend bucket flap. THIS SECTION IS COMPLETE, MOVE ON TO NEXT SECTION CURVE™...
-
Page 28: Complete Installation
INSTALLATION GUIDE COMPLETE INSTALLATION AP 7000 VARIATION First, remove cabinet support bracket by first unfasten- OEM Cabinet ing middle tray locking mechanism as shown using a Support Bracket Phillips screwdriver and 7/16” wrench. Retain nut and bolt from locking mechanism to use in Step 2. Locking Mechanism Screwdriver Then, insert the Cabinet Support Bracket (VE8716) - Page 29 INSTALLATION GUIDE COMPLETE INSTALLATION Hinge Side of Door Wing Handle Header Cutout and Cash Box Groove Next, reinstall the cash box and rotate the wing handle Then, on the hinge side of the CURVE door, align tabs on Header cam latch counter-clockwise on the box to lock in place (VE1016551) with cutout and groove inside of existing trim and as shown set over the top of the door.
- Page 30 INSTALLATION GUIDE COMPLETE INSTALLATION Next, check that the header is aligned flush with the vertical trim on the hinge (left) side of the door. Then, hold header firmly and tighten Phillips head screw and hex nut to a snug fit. Header Header Vertical Trim...
- Page 31 INSTALLATION GUIDE COMPLETE INSTALLATION AP 7000 VARIATION For the AP 7000 variation, using ma- chine screws, attach Block Out Plate (VED3596) in both holes on both sides of the cabinet. Image (A) on the left shows the installation point on the right side of the cabinet.
-
Page 32: Adjust The Door
INSTALLATION GUIDE ADJUST THE DOOR AFTER INSTALLATION, THE DOOR MAY REQUIRE SOME ADJUSTMENT OR ALIGNMENT FOR A PROPER FIT. WHEN CLOSING THE DOOR, DO NOT FORCE OR NOTICE SLAM SHUT. THIS MAY CAUSE DAMAGE TO THE DOOR FRAME OR LOCK BAR. THIS TASK SHOULD BE COMPLETED WITH AN ADDITIONAL PERSON. -
Page 33: Ucb™ Connections For Curve™ Door
INSTALLATION GUIDE UCB™ CONNECTIONS FOR CURVE™ DOOR DESCRIPTION BACKLIT KEYPAD (IF APPLICABLE) VE SUPPLIED DROP SENSOR DOOR SWITCH VE SUPPLIED LED LIGHTING (IF APPLICABLE) DISPLAY MOTORS/CABINET 24V AC POWER KEYPAD MOTION SENSOR CURVE™ Door for AP 113, AP 123, AP 7000 To TOC Overview... - Page 34 INSTALLATION GUIDE NOTES Overview To TOC CURVE™ Door AP 113, AP 123, AP 7000...
- Page 35 INSTALLATION GUIDE NOTES CURVE™ Door for AP 113, AP 123, AP 7000 To TOC Overview...
-
Page 36: Product Warranty
INSTALLATION GUIDE PRODUCT WARRANTY Limited Warranty and Disclaimer. VE warrants that the Products, including without limitation, their component Part(s), sold will be of the kind and quality described herein and will be free of defects in workmanship or material. This Warranty shall extend for the Warranty Period set forth below following the date of delivery of such Products to Buyer.