Dräger X-am 3500 Quick Start Manual

X-am 3500 / 8000 │ Notes on approval / Sensor data
Approvals / Marking
X-am 3500
X-am 3500
P/N: XXXXXXX
TC RU C-DE.BH02.B.00744
data
S/N: ARXX-XXXX
matrix PO Ex da ia I Ma X
code
0Ex da ia IIC T4 Ga X
Type: HFG 0000 IP 67
I M1 / II 1G
Ex da ia I Ma
Ex da ia IIC T4 Ga
0158
18.70148494
IECEx BVS 17.0034X Class I, Zone 0, A/Ex da ia IIC T4 Ga
BVS 17 ATEX E 040 X Class II, Div. 1, Groups E, F, G
PFG 19 G 001X C22.2 No. 152 for comb. sensors, Class I only
Use only power supply
Dräger LBT 02**
X-am 8000
X-am 8000
P/N: XXXXXXX
TC RU C-DE.BH02.B.00535
data
S/N: ARXX-XXXX
matrix PO Ex da ia I Ma X
code
0Ex da ia IIC T4 Ga X
Type: HFG 0010 IP 67
I M1 / II 1G
Ex da ia I Ma
Ex da ia IIC T4 Ga
0158
18.70148494
IECEx BVS 17.0034X Class I, Zone 0, A/Ex da ia IIC T4 Ga
BVS 17 ATEX E 040 X Class II, Div. 1, Groups E, F, G
PFG 19 G 001X C22.2 No. 152 for comb. sensors, Class I only
Use only power supply
Dräger LBT 02**
1)
Serial No.
1) Serial Number key: The third letter of the serial number specifies the
manufacturing year: M = 2019, N = 2020, P = 2021, R = 2022, S = 2023,
T = 2024, U = 2025, W = 2026, X = 2027, Y = 2028,
Z = 2029, etc. (Letters G, I, O, Q are omitted)
Example: Serial Number ARMB-0001: the third letter is M, which means
that the unit was manufactured in 2019.
Only for USA:
Changes or modifications not expressly approved by the party res-
ponsible for compliance could void the user's authority to operate
the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment ge-
nerates, uses and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for

help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including in-
terference that may cause undesired operation.
FCC responsible party:
Draeger Inc.
7256 S. Sam Houston W. Parkway
Suite 100
Houston, Tx 77085 USA
phone: +1 346-802-6111
e-mail: DIHouston.Approvals@draeger.com
Only for Canada:
CAN ICES-3 (B)/NMB-3(B)
Only for CSA (Canadian Standards Association):
WARNING: Wireless communication is intended for use as a se-
condary remote alarm status notification only. Primary alarming of
combustible gas hazards is provided locally by detector.
WARNING: Applicable to CLASS II DIV.1, GROUPS E, F, and G
certification: CSA Std. 152 does not have any requirement for Class
II environment and therefore this device has not been performance
tested for Class II hazardous location. The sensor may become
clogged and not detect gas properly or warn the user of its inability
to detect gas.
AVERTISSEMENT: La communication sans fil est destinée à être
utilisée uniquement comme notification d'état d'alarme secondaire
à distance. L'alarme primaire des risques de gaz combustible est
fournie localement par le détecteur.
AVERTISSEMENT: Applicable à la certification CLASSE II DIV.1,
GROUPS E, F et G: CSA Std. 152 n'a pas d'exigence pour l'en-
vironnement de classe II et par conséquent, cet appareil n'a pas été
testé pour un emplacement dangereux de Classe II. Le capteur
peut se boucher et ne pas détecter correctement le gaz ou avertir
l'utilisateur de son incapacité à détecter le gaz.
Declaration of conformity for X-am 3500 / 8000