Table of Contents
Advertisement
Notice
● If 真空開 -1˚C (Vacuum Compartment Subzero) / 真空開 +1˚C
(Vacuum Compartment Chiller) indicator lamps fl ash, the vacuum
function may not be in the normal conditions.
● The vacuum function will not work properly if some
package of foods is pinched in or dirt/dust is adhered to
the vacuum packing or the vacuum release valve (in blue).
Pay attention that no package of
the foods is pinched.
● Moisture in juicy foods stored in the Vacuum
Compartment will evaporate and cause
dew condensation or frost in the Vacuum
Compartment. If water drops and/or frost
adheres inside the Vacuum Compartment or
around the door of the Vacuum Compartment,
wipe off them with a dry cloth.
● For troubleshooting about the Vacuum Compartment, see Troubleshooting
● Replace an old vacuum packing if the vacuum state can ' t be kept well.
How to maintain/care the Vacuum Compartment
Be sure to remove foods contained in the Vacuum Compartment.
1
1
Pull the door, lift up the edge
of the Vacuum Case (with the
door) lightly and then pull it out.
How to maintain/care the Vacuum Compartment with the vacuum packing removed
Remove the Vacuum Case (with the door) fi rst. Remove the door of the Vacuum Compartment and the vacuum packing in the following
way, and then maintain/care them. Do not remove other things except the door of the Vacuum Case and the vacuum packing.
■ How to remove the door of the Vacuum Case
1
Insert a plastic wrap case or
something like that under the case
so that the door of the case will
be fl oating and removable without
diffi cult.
■ How to maintain/care the vacuum packing
1
Tab
Grasp the tab of the vacuum packing on the observer ' s
upper right and remove it by hand carefully.
■ How to install the door of the Vacuum Case
Axis of the door
1
of the Vacuum
Case
Support
Align the axis of the door of the Vacuum
Case to the support.
● Do not rinse the door of the Vacuum Case in water.
Caution
● If detergents and others except lukewarm water are used to clean the vacuum packing, the vacuum packing
may be damaged, deformed or change in color, which may cause that the vacuum state can't be kept well.
● Loosened vacuum packing or loose-fi tting door of the Vacuum Case may cause that the vacuum state can't be kept well.
Pg.55
Waste thread
Scraps
2
2
Wipe the vacuum packing, the inside the Vacuum Case and the
packing support, using a soft cloth wet by lukewarm water.
2
Tab
Unset the tab at the edge of the
Vacuum Case.
2
Rinse dirty portion in water with a soft
wash sponge, wipe off the moisture with
a dry cloth, and then let it dry naturally.
Remove dirt in the groove of the vacuum
packing on the door.
※ Do not use the detergents, etc.
2
Rotate the door of the Vacuum Case
upon around the upper portion.
The indicator
lamp fl ashes.
● The vacuum function will not work properly if the
vacuum packing or the vacuum release valve (in blue)
comes off or is loosened.
● Make sure to wipe off
spilled water or food soup
soon, if any. Water will be
frozen, which may lead to
a trouble of the Vacuum
Case (with the door).
Pg.55
Pg.57
3
3
Put the Vacuum Case (with the door) back into
the Vacuum Container, and then lower the lock
of the handle.
Rotation criteria
3
Hold down the door of the Vacuum
Case to unset the axis.
3
Tab
Align the tab to the notch accurately, and
then combine them together.
3
Pull up the door of the Vacuum Case while
holding the bottom of the Vacuum Case.
Check the tab is in place.
Vacuum release valve
Vacuum release valve
4
Rotate the door of the Vacuum
Case upon the upper side of the
door, and pull it out.
Notch of the groove
43
Advertisement
Table of Contents
