1. Manuals
  2. Brands
  3. RadiSys Manuals
  4. Motherboard
  5. KP915GV
  6. Quick start manual

RadiSys KP915GV Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
The following information is provided to help you quickly configure, install and operate your
RadiSys KP915GV motherboard. Refer to the product manual for more detailed information.
The RadiSys KP915GV is an ATX-family motherboard that meets the ATX form factor specifications, is
®
based on the Intel
915GV chipset, and support selected Intel
Features include 4 DIMM sockets, integrated video, system monitoring, three PCI, two x1 PCI-E, and one
ADD2 slots, eight USB 2.0 ports, and up to two optional Ethernet channels on a board measuring 9.6 x 12
inches.
Board Layout and Key Component Identification
59
1
2
3
4
5
6
7
8
9
10
11
12
13 14 15 16 17 18 19 20 21 22 23 24 25
58
57
(Optional)
Endura KP915GV
ATX Motherboard
Quick Start Guide
®
™
Celeron
D and Pentium
56
55
54
53
52
26
27
28 29 30
© 2005 RadiSys Technology (Ireland) Ltd.
®
4 processors.
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31

Advertisement

Table of Contents
loading

Related Manuals for RadiSys KP915GV

Summary of Contents for RadiSys KP915GV

  • Page 1 The following information is provided to help you quickly configure, install and operate your RadiSys KP915GV motherboard. Refer to the product manual for more detailed information. The RadiSys KP915GV is an ATX-family motherboard that meets the ATX form factor specifications, is ®...
  • Page 2 Primary power supply connector VGA monitor RTC battery IDE connector Ethernet port 2 1394 PHY TPM header (TSB81BA3I) I/O panel USB port 5 1394 header FDD connector I/O panel USB port 6 USB port 1 header © 2005 RadiSys Technology (Ireland) Ltd.

  • Page 3: Quick Start

    Both the processor voltage and operating frequency are automatically adjusted by the motherboard to suit the installed processor. A complete list of tested processors is available from the RadiSys web page http://www.radisys.com. CPU Installation: Below is the CPU socket illustration. Follow these procedures to install a CPU.
  • Page 4 DO NOT use finger to lift the locking lever, as injury could occur to the finger and the socket could be damaged. 4. Lift up the lever. Use thumb to open the load plate. Be careful not to touch the contacts. © 2005 RadiSys Technology (Ireland) Ltd.
  • Page 5 CPU cooling fan and make sure that the cooling fan works normally at all times in order to prevent overheating and damaging to the CPU. Please refer to your CPU fan user guide to install it properly. © 2005 RadiSys Technology (Ireland) Ltd.

  • Page 6: System Memory

    DIMMs is installed, the maximum available memory will be approximately 3.24GB, with the balance of the address space being consumed by other resources in the system. A complete list of tested memory is available from the RadiSys web page http://www.radisys.com. Memory Installation: This motherboard includes four 240-pin slots with 1.8V for DDR2.
  • Page 7 (Jumper between pins 2 & 3) This is the factory default position. Either this position or no jumper installed, is the normal operating configuration. Installing a jumper between pins 1 & 2 clears (resets) the CMOS. © 2005 RadiSys Technology (Ireland) Ltd.

  • Page 8: Technical And Product Support

    RadiSys Web site http://www.radisys.com. Note: It is recommended that only the drivers supplied by RadiSys be used as those posted on the device manufacturer’s Web sites may not function correctly.

  • Page 9: Connector Descriptions

    PWRLED+ HDLED- PWRLED+ PSON# RESETSW- PWRSW+ RESETSW+ PWRSW- +5V Fused SPKR+ Not Used SPKR- PWROK Not Used +5VSBY PWRLED- SPKR- +12V Not Used TAMPERSW+ PWRLED- TAMPERSW- ATX12V Power Connector (CN8) Signal Signal +12V +12V © 2005 RadiSys Technology (Ireland) Ltd.

Table of Contents