One-Year Limited Warranty - IKEA SLADDA Owners & Safety Manual

GB HELMET OWNER'S SAFETY MANUAL
6 7
If you choose to cut the chinstrap, leave a protrusion of approx. 2 inches or 4
cm above the lock. Have an adult heat the cut ends carefully with a match to
prevent the webbing from unravelling. Be careful with high heat near the helmet
because the strap and helmet are flammable. Be careful to avoid contact with
melted nylon.
9
WARNING
In the event of an impact or blow, do not use this helmet. The helmet is de-
signed to absorb shock by partial destruction of the shell and liner. There
may be damage to the helmet that is not visible to the user and the hel-
met may be no longer adequate to protect the head against further im-
pacts. In the event of an impact or blow, even if there is no visible damage,
the helmet should be replaced with a new one and the old one destroyed.
WARNING
The helmet can be damaged by contact with common substances (for ex-
ample, certain solvents [ammonia],
leum products or abrasives), and this damage may not be visible to the
user. Do not use this helmet if it has been exposed to such substances.
WARNING
• Regularly check the helmet for signs of damage.
• Do not apply stickers or paint to the helmet as this can be damaging to the
helmet.
• Do not remodel or misuse the helmet.
• Do not expose the helmet to temperatures exceeding 60˚C (140˚F). Do not
4
8
Run the chinstrap through the lock as noted be-
low and use the "O-Ring" to secure any excess
strapping. See Illustration 9.
cleaners [bleach],
store behind glass, e.g. in a car (risk of burning glass effect) or near heaters,
etc.
• This helmet has a limited life time and should be replaced when it shows
obvious signs of wear, but at the latest within 3 years after the date of manu-
facture.
• The helmet, inner pads and head ring can be cleaned using lukewarm water,
solvent-free detergents and a soft cloth.
• Only use original spare parts.
This helmet is certified according to one or more of the following standards:
89/686/EWG: Guidelines for personal protection equipment
EN1078+A1:02/2013 – European standard for cyclists, skateboarders and
inline skaters. Tested by C.R.I.T.T. Sport - Loisirs Notified Body No.: 0501
C.P.S.C. 16 CFR Part 1203 United States Federal Safety Standard for Bicycle
Helmets (Consumer Product Safety Commission)
AS/NZS 2063:2008+A1:2009 - Tested under BSI Benchmark License ID # 572239
EN 1078+A1:02/2013
ONE YEAR LIMITED WARRANTY
The following information relates to helmets purchased in the USA only.
IKEA warrants to the original purchaser of this helmet that it is free of
defects in material and workmanship, under normal use and service, for
a period of one year from the original date of purchase. This warran-
ty does not apply to defects or physical damage resulting from abuse,
neglect, improper repair, improper fit, alterations, or use unintended
by the manufacturer. If your IKEA helmet is found to be defective in
materials or workmanship within one year from the date of original pur-
chase, then the IKEA country distributor may, after evaluation of the
helmet and at its sole option, either repair or replace the helmet free
of charge. Just take the helmet to the place of purchase, with a letter
paints, petro- indicating the specific reason(s) for returning the helmet and your proof
of purchase. IKEA does not warranty any helmet damaged due to heat
or contact with solvents. This warranty is in lieu of all other agreements
and warranties, general or specific, express or implied, and no person
or representative is authorized to assume liability on behalf of IKEA in
connection with the sale or use of this product. This warranty does not
affect your statutory rights.
CERTIFIED
PRODUCT
AS/NZS
2063:2008+A1:2009
BMP 572239
5