Table of Contents
Advertisement
Quick Links
Operating Instructions • Warning Information
Parts Breakdown
™
SE70
Touch Up Gravity Feed
Spray Gun
SPECIFICATIONS
Fluid Orifice . . . . . . . . . . . . . . . 0.8mm
Air Inlet. . . . . . . . . . . . . . . . . . 1/4 NPT
Rec. Max. Inlet Pressure . . . . . . . . 35 PSI
Nozzle Pressure. . . . . . . . . . . . . . 25 PSI
CFM. . . . . . . . . . . . . . . . . 3.5 @ 35 PSI
Cup Size. . . . . . . . . . . . . . . . . . . 150cc
SE70
1
Rev. 05/16/05
SE70_OpMan.indd 1
5/16/05 4:37:56 PM
Advertisement
Table of Contents
Related Manuals for Matco Tools SE70
Summary of Contents for Matco Tools SE70
- Page 1 Operating Instructions • Warning Information Parts Breakdown ™ SE70 Touch Up Gravity Feed Spray Gun SPECIFICATIONS Fluid Orifice ....0.8mm Air Inlet....1/4 NPT Rec.
- Page 2 The hearing loss. Protect yourself from mask must be compatible with the material noise. Noise levels vary with work being sprayed and its concentration. surface. Wear ear protectors. SE70 Rev. 05/16/05 SE70_OpMan.indd 2 5/16/05 4:37:58 PM...
-
Page 3: Air Supply
GRAVITY FEED CUP HOOKUP For fine finishing with limited spraying. Air pressure for atomization is regulated at extractor. Amount of fluid is adjusted by fluid control screw on gun, viscosity of paint, and air pressure. SE70 Rev. 05/16/05 SE70_OpMan.indd 3 5/16/05 4:37:58 PM... - Page 4 If the spray is too thick, close the fluid finished. control screw. Regulate the pattern width and repeat adjustment of spray as needed. Spray pattern may be infinitely adjusted from round to flat. SE70 Rev. 05/16/05 SE70_OpMan.indd 4 5/16/05 4:38:00 PM...
-
Page 5: Operation
If the parts can not easily be turned by hand, be sure you have the correct parts, unscrew, realign, and try again. NEVER use excessive force in matching parts. SE70 Rev. 05/16/05 SE70_OpMan.indd 5 5/16/05 4:38:00 PM... -
Page 6: Troubleshooting
A.) Gun held too far from surface. Thin, sandy coarse finish. B.) Atomization pressure set B.) Adjust atomization pressure. too high. Thick, dimpled finish Gun held too close to surface. Move gun farther from surface. resembling orange peel. SE70 Rev. 05/16/05 SE70_OpMan.indd 6 5/16/05 4:38:01 PM... - Page 7 PARTS BREAKDOWN - SE70 Optional nozzle kits available: RS9001-0.5 0.5mm RS9001-0.8R 0.8mm (color coded red) RS9001-1.0 1.0mm Nozzle kits consist of: 1 Air Cap 1 Fluid Needle 1 Fluid Nozzle SE70 Rev. 05/16/05 SE70_OpMan.indd 7 5/16/05 4:38:02 PM...
-
Page 8: Warranty
PARTS LIST - SE70 ™ Index # Part # Description Qty. Index # Part # Description Qty. RS2001A Air Cap (0.8mm) - red RS2035 Air Inlet Fitting RS2006 Fluid Nozzle (0.8mm) RS2041A Air Valve Assembly RS2007 Air Distribution Ring RS2013...