Related Manuals for Sleipner SX35POD
Summary of Contents for Sleipner SX35POD
- Page 1 Installation Guide For DC External POD Electric Thruster Models SX35POD, SX50POD DOCUMENT ID: SLEIPNER MOTOR AS 6398 REVISION: P.O. Box 519 DATE: N-1612 Fredrikstad 2022 Norway LANGUAGE: www.sleipnergroup.com...
-
Page 2: Table Of Contents
Product Spare Parts and Additional Resources ..........................19 Warranty Statement .................................... 19 Products SM150536 | SXPOD-35/50-50MM - Hydropod complete kit for in water flow configuration Sleipner Motor AS P.O. Box 519, Arne Svendsensgt. 6-8 N-1612 Fredrikstad, Norway MC_0020 HydroPOD 35 & 50... -
Page 3: Responsibility Of The Installer
• If able ensure that stern-drives/ trim-tabs do not interfere with the water flow from the thruster as this can reduce the thrust effectiveness considerably. We recommend the use of our Sleipner cowls to enhance the performance and allow installation in shallow draft boats. Sleipner cowls will also minimise the effect if stern-drives/ trim-tabs obstruct the thruster. -
Page 4: Product Measurements
Product Measurements MC_0268 Measurement Measurement description code mm inch mm inch Mould Height 7,08 7,08 Tube Height 7,20 7,20 Width Length 24,8 24,8 Measurement 5.08 5.08 Measurement Measurement Measurement Measurement Measurement Measurement Measurement 35.8 35.8 Measurement *Valid for SX & SXP MG_0080 HydroPOD 35 &... - Page 5 Product Measurements 187 mm 7’36” 170 mm 6’69” 121 mm 4’76” MG_0132 HydroPOD 35 & 50 6398 2022...
-
Page 6: Product Specifications
Product Specifi cations MC_0149 SX/P Thruster SX35 SX50 Description SXP35 SXP50 Nominal Voltage Thrust 12V 43 kg / 94 lbs 62 kg / 136 lbs Thrust 10.5V 35 kg / 77 lbs 50 kg / 110 lbs Maximum Operation Time S2 motor at 2 - 3 min. -
Page 7: Positioning Of The Sx With Hydrodynamical Cover
Positioning of the SX with Hydrodynamical Cover MC_0072 Aim to install the thruster as far forward/ Aft as possible Due to the leverage effect around the boats’ pivot point. The relative distance difference from the boat pivots’ point to the thruster will determine the amount of real thrust for the boats, rotation. -
Page 8: Tunnel Installation
Tunnel Installation MC_0074 Connect both ends of the tunnel to the thruster motor. All hooks must be completely interlocked making the inside of the tunnel smooth. (NB: Ensure tunnel moulding around the gear leg and tunnel top align.) IMPORTANT Ensure all snap-lock positions are correctly connected into place. Ensure top lips tabs into the motor inserts. -
Page 9: Hydropod Modification
Hydropod Modifi cation MC_0269 ! Please refer to the graphic for special considerations relating to your model ! Defi ne the location to install the thruster. (NB: Ensure internally the thruster will not obstruct any objects. Ensure cables internally do not obstruct any objects. -
Page 10: Hydropod Installation
Hydropod Installation MC_0269 ! Please refer to the graphic for special considerations relating to your model ! Temporally fasten the Hydro pod to the hull using the SX thruster bolts. Mark the remaining Hydro pod holes (1 rear, 2 front) and drill holes. Clean the area from dust for installation of the thruster. -
Page 11: Propeller Installation
Propeller Installation MC_0016 Centre the drive pin and Insert the propeller onto the shaft spine. Rotate the propeller until the drive pin aligns with the internal slot in the propeller. Insert the washer to the end of the shaft spline. Tighten with the propeller lock-nut. Apply anti fouling to the gear leg and propeller. -
Page 12: Grids Or Cowls Assembly
Grids or Cowls assembly MC_0074 1. Attach the cowls or grids with included bolts. (NB: If installation of the cowls ensure the appropriate twist of the cowl to direct water away from obstacles) *Cowl *Grid Grids and cowls can not be installed in combination. -
Page 13: Electrical Installation
Sleipner offers both manual main switches and Automatic Main Switches (AMS). Sleipner AMS is controlled by the control panel in addition to the option of manual operation. Turning on the control panel does also turn on the automatic main switch. -
Page 14: Control Box Installation
Control Box Installation MC_0075 Follow the below steps to install the Control Box. Additional installation details can be found in the corresponding graphics. Pull the blue SX Thruster Hose around the cable harness coming out of the SX Thruster. Fasten the hose clamp. Defi ne the location to install the Control Box. - Page 15 Control Box Installation MC_0075 Follow the cable marking and fasten motor power cables coming from the SX Thruster in the control box. The motor power cables are marked A1 and A2 and should be fastened to the terminal with corresponding marking. Place the ring cable lug connected to the white wire between the lug of the motor power cable and the nut.
-
Page 16: Visual Wiring Diagram
Visual Wiring Diagram Refer to your control panel manual for Control detailed information on connecting the SX panel system to your control device Control Box 4-lead cable SX thruster hose Automatic SX POD thruster MAIN SWITCH (See Main Switch installation manual) Fuse 5A THRUSTER BATTERY... -
Page 17: Control Panel Installation
Control Panel Installation MC_0398 For Control Panel installation please refer to the Installation Guide accompanying the control panel to be installed. Installation Guide Control Panel SLEIPNER MOTOR AS DOCUMENT ID: REVISION: P.O. Box 519 N-1612 Fredrikstad DATE: Norway www.sleipnergroup.com LANGUAGE: HydroPOD 35 &... -
Page 18: Pre-Delivery Checklist
Pre-delivery Checklist MC_0081 ..Propeller is fastened correctly to the shaft... Propeller turns freely in tunnel... Primer and anti-fouling have been applied to the gear house and propeller but NOT on the anode or the gear house lid where the propeller is fastened. (NB: Do not use abrasive tools damaging the existing Epoxy coating when preparing for antifouling paint.) .. -
Page 19: Service And Support
11. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. Patents MC_0024 At Sleipner we continually reinvest to develop and offer the latest technology in marine advancements. To see the many unique designs we have patented visit our website www.sleipnergroup.com/patents HydroPOD 35 & 50... - Page 20 © Sleipner Group, All rights reserved The information given in the document was right at the time it was published. However, Sleipner Group cannot accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifi cations without notice.
Need help?
Do you have a question about the SX35POD and is the answer not in the manual?
Questions and answers