Sleipner 86-08950 User Manual

Control panels
Hide thumbs Also See for 86-08950:

Advertisement

Quick Links

User Manual
Including Installation For Control Panels
86-08950, 86-08955
86-08950
86-08955
DOCUMENT ID:
6666
REVISION:
3
DATE:
2022
EN
LANGUAGE:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 86-08950 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sleipner 86-08950

  • Page 1 User Manual Including Installation For Control Panels 86-08950, 86-08955 86-08950 86-08955 DOCUMENT ID: 6666 REVISION: DATE: 2022 LANGUAGE:...
  • Page 2: Table Of Contents

    Control Panel Installation..................................8 Measurements ......................................9 Service and Support................................... 10 Product Spare Parts and Additional Resources ..........................10 Warranty Statement .................................... 10 Products 86-08950 - Kontrollpanel ankervinsj 86-08955 - Rundt kontrollpanel ankervinsj MC_0020 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 3: Responsibility Of The User Operating Windlass

    • Keep the engine running during windlass operation to ensure good battery capacity. • Sleipner Motor AS is not responsible for damage or injury caused by the use of our windlass systems. • While dropping anchor, do not push the “UP” button until the anchor is resting at the seabed.
  • Page 4 To ensure a long battery lifetime, the remote control switches off automatically 4 min. after the last button was pressed. (NB: Remote and receiver is normally connected and ready to use. See own manual for more information and variants.) RCT-21 RCT-23 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 5: Visual Wiring Diagram

    After the first stop is detected and pull is resumed by repressing the “up” again and the controller will pull the anchor in at reduced speed and with a lower allowable pull until the second stop is registered. At this point, the anchor should rest in the bracket without unnecessary high tension on the rope, windlass, fasteners etc. MG_0376 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 6: Control Panel

    Double ‘ON’ buttons to activate the control panel Control Panel 86-08955 Lower anchor Raise anchor Double ‘ON’ buttons to activate the control panel 'OFF' button to deactivate the control panel MG_0401 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 7: Responsibility Of The Installer

    MC_0424 • Always use original Sleipner rope. (NB: While dropping anchor, do not push the “UP” button until the anchor is resting at the seabed.) • Windlass and accessories must be installed and used in a manner that will not cause damage or injury.
  • Page 8: Control Panel Installation

    Plug cables into the connectors at the rear of the control panel. Insert the control panel in place and fasten screws. Insert the control panels covering caps. Gasket Screws Cables Gasket Cover caps Screws Cables MG_0402 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 9: Measurements

    Raised height above the dashboard 0.26 10.7 0.42 Depth behind the dashboard (not inc. cables) 1.61 Panel screw hole diameter 0.12 0.10 Distance between panel screw holes 2.09 Models: 86-08950 *Cut out Models: 86-08955 *Cut out MG_0400 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 10: Service And Support

    A+B+C+D+E+F <6m : 25mm2 A+B+C+D+E+F=6-16m : 35mm2 A+B+C+D+E+F>16m : 50mm2 Autostop Sensor Motor (Not applicable for chain) To change motor direc�on: Change cables D1 and D2 on motor Maxi MG_0403 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 11 Cable size A,B and C : f total length A+B+C <10m : 25mm2 A+B+C >10m : 35mm2 Autostop sensor (opt.) Motor Mini/Midi To change motor direc�on: Change cables D1 and D2 in control box MG_0404 Control Panels 86-08950 & 86-08955 6666 2022...
  • Page 12 © Sleipner Group, All rights reserved The information given in the document was right at the time it was published. However, Sleipner Group cannot accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifi...

This manual is also suitable for:

86-08955

Table of Contents