Subscribe to Our Youtube Channel
Related Manuals for Sleipner SH1000
Summary of Contents for Sleipner SH1000
- Page 1 Installation Guide For Hydraulic Thruster Models SH1000, SH1400 DOCUMENT ID: SLEIPNER AS 5939 REVISION: P.O. Box 519 DATE: N-1612 Fredrikstad 2021 Norway LANGUAGE: www.sleipnergroup.com...
-
Page 2: Table Of Contents
SM102941 | SH1400/610-BA160 - SH1400 Tunnel thruster, BA160 SM908034 | SH1400/610-BA80 - SH1400 Tunnel thruster, BA80 SM102972 | SH1000/513-BA110D13 - SH1000 Tunnel thruster, BA110 SM103522 | SH1000/513-BA90 - SH1000 Tunnel thruster, BA90 SM114788 | SH1000/513-BA80 - SH1000 Tunnel thruster, BA80... -
Page 3: Responsibility Of The Installer
Sleipner products. If you are interfacing the S-Link™ bus by agreement with Sleipner through a designated Sleipner supplied interface, you are still required to install at least one original Sleipner control panel to enable efficient troubleshooting if necessary. -
Page 4: Thruster Measurements
Thruster Measurements MC_0189 *1000 *1400 Measurement Measurement description code mm inch mm inch Internal tunnel diameter 7,28 24,02 Motor Height 19,13 19,69 Width 15,67 15,67 Length 15,67 15,67 Water Depth 29,53 35,43 Minimum tunnel length 29,53 29,53 TL (recommended) Recommended tunnel length 1000 39,37 1000... -
Page 5: Thruster Specifications
Thruster Specifi cations MC_0148 Description * 1000 * 1400 Light duty thrust up to (kg * lbs) Heavy duty thrust up to (kg * lbs) 1000kg * 2205lbs 1400kg * 3085lbs Typical Boat Size (m * ft) 30m - 45m * 100ft - 150ft 40m - 55m * 130ft - 175ft Propulsion System Twin Counter Rotating... - Page 6 Technical Specifi cations MC_0112 60 % 70 % 80 % 90 % 100 % Flow Pressure Flow Pressure Flow Pressure Flow Pressure Flow Pressure L/min -Bar 91,0 99,0 USG-PSI 24.0 3190 26.2 3712 L/min -Bar 98,0 106,0 USG-PSI 25.9 2973 28.0 3466 BA80...
-
Page 7: Technical Requirements / Hydraulic Hose Connections To Motor
07.03.2014 Hyd. motor 16 ccm Copyright All rights reserved Copyright All rights reserved Title Title Hyd. motor 16 ccm Hyd. motor 16 ccm SLEIPNER MOTOR AS Pre fi ll motor housing with BA-motor: Part nr Weight Size Scale Edition Sheet... -
Page 8: Positioning Of The Tunnel / Thruster
Positioning of the tunnel / thruster MC_0003 Aim to install the thruster as far forward as possible (1) Due to the leverage effect around the boats’ pivot point. The distance difference from the boat pivots’ point to the thruster will determine the amount of real rotation power for the boat. -
Page 9: Tunnel Length
Tunnel Length MC_0003 Optimal tunnel length Achieving the correct tunnel length depends on many factors from the hull type, operation and environmental conditions. Tunnels should avoid being longer than 4 x the tunnel diameter as this will reduce thruster performance. (NB: Installing long length tunnels can flex/ bend over time and may require additional support. -
Page 10: Tunnel Installation In Sailboats
Tunnel installation in Sailboats MC_0003 Some sail boats have a flat bottom and shallow draft in the bow section. This can make installing the thruster as far forward from the boats main pivot point diffi cult. (Fig. 1). However, it is possible to install a tunnel thruster in most sail boats, even when the hull does not directly support the fi tting of a tunnel. Instead fi... -
Page 11: Water Deflection
Water Deflection MC_0003 A possible problem in sail boats or fast powerboats is that a non-rounded surface can generate drag from the back face of the tunnel, as it creates a “flat” area facing the flow of water. This problem can be solved in two different ways, depending on what is possible or easier to perform. The best solution which generally reduces the most drag is to make a recess in the hull at the back of the tunnel. -
Page 12: Tunnel Ends
Tunnel Ends MC_0003 Rounded tunnel ends will maximise thrust and minimise noise and cavitation. For best performance round the tunnel connection to the hull-side as much as possible. The minimum rounding has a radius of 10% of the diameter of the tunnel. -
Page 13: Tunnel Installation
Tunnel Installation MC_0003 IMPORTANT We recommend that a professional does the fi breglass, steel or aluminium fi tting of the tunnel. These instructions are only general instructions and do not explain in any way the details of fi breglass work. Problems caused by faulty installation of the tunnel, are the installers full responsibility. - Page 14 Tunnel Installation MC_0003 With tunnel installed and cast. Round the edges with a radius of 10% of the tunnel diameter. For steel/ aluminium hulls make a slope with a length of 10-15% of the tunnel diameter. (NB: If this is not possible, round the tunnel end as much as possible.) Additionally cast two layers on the outside of the tunnel/ hull in a 10cm area Follow the same method if making the deflector/ spoiler.
-
Page 15: Stern Tunnel Installation
Stern Tunnel Installation MC_0003 For Stern Thruster installation please refer to the supplied manual in your Sleipner product delivery Installation Guide Stern Thruster SLEIPNER AS DOCUMENT ID: P.O. Box 519 REVISION: DATE: N-1612 Fredrikstad Norway www.sleipnergroup.com LANGUAGE: SH 1000 & 1400... -
Page 16: Gear Leg & Motor Bracket Installation
Gear Leg & Motor Bracket Installation MC_0002 ! Please refer to the graphic for special considerations relating to your model ! Mark the tunnel centreline and the boat’s centreline. (NB: Install the gear leg and propeller as shown above for the thrust direction to correspond with the control panel. -
Page 17: Propeller Installation
Shaft and propeller taper must be 100% clean before assembling. Apply mounting oil before assembling propeller to shaft. Tighten to: SH360/400 - 90Nm SH700 - 200Nm SH1000/1400 - 400Nm Apply Loctite 243 or similar MG_0152 SH 1000 & 1400 5939 2021... -
Page 18: Motor Installation
Motor Installation MC_0114 ! Please refer to the graphic for special considerations relating to your model ! Install the motor onto the motor bracket ensuring the couplings are engaged together correctly (top and bottom). (NB: The motor can be placed in all directions on the motor bracket. -
Page 19: Oil Tank Installation
Oil Tank Installation MC_0023 ! Please refer to the graphic for special considerations relating to your model ! Install the oil tank above the waterline by at least 20% of the distance from the waterline to the centre of the tunnel. This ensures enough overpressure for the oil in the gear leg. -
Page 20: Crossover Valve
Crossover Valve Crossover valve must be mounted as close as possible to the motor SH 400 1/2” valve SH 700, 1000, 1400 1” valve Valve coil w/ connector MG_0341 SH 1000 & 1400 5939 2021... -
Page 21: S-Link System Description
MC_0120 S-Link is a CAN-based control system used for communication between Sleipner products installed on a vessel. The system uses BACKBONE Cables as a common power and communication bus with separate SPUR Cables to each connected unit. Units with low power consumption are powered directly from the S-Link bus therefore one power cable must be connected to the BACKBONE Cable through a T-Connector. -
Page 22: Control Panel Installation
Control Panel Installation MC_0398 For Control Panel installation please refer to the supplied manual in your Sleipner product delivery Installation Guide Control Panel SLEIPNER AS DOCUMENT ID: P.O. Box 519 REVISION: DATE: N-1612 Fredrikstad Norway www.sleipnergroup.com LANGUAGE: SH 1000 & 1400... -
Page 23: Pre-Delivery Checklist
Checklist for Hydraulic Thrusters MC_0049 ..Propeller is fastened correctly to the shaft... Propeller turns freely in tunnel... Lower-unit is fi lled with gear oil... Oil-drain screw is tightened and the copper seal is present... The anode holding screw is tightened well with thread glue... -
Page 24: Service And Support
10. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. Patents MC_0024 At Sleipner we continually reinvest to develop and offer the latest technology in marine advancements. To see the many unique designs we have patented visit our website www.sleipnergroup.com/patents SH 1000 & 1400... - Page 25 Notes MC_0037 ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................SH 1000 & 1400 5939 2021...
- Page 26 Notes MC_0037 ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................SH 1000 & 1400 5939 2021...
- Page 27 Notes MC_0037 ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................SH 1000 & 1400 5939 2021...
- Page 28 © Copyright Sleipner Motor AS, 2021 The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifi...
Need help?
Do you have a question about the SH1000 and is the answer not in the manual?
Questions and answers