Page 1 Aspen 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....7 Rollover Warning .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION ROLLOVER WARNING This Owner’s Manual has been prepared with the assis- Utility vehicles have a significantly higher rollover rate tance of service and engineering specialists to acquaint than other types of vehicles. This vehicle has a higher you with the operation and maintenance of your vehicle.
Page 6: How To Use This Manual
INTRODUCTION 5 belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 7 6 INTRODUCTION...
Page 8: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Security Alarm System — If Equipped ..18 Ignition Key Removal .
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information ....25 Window Lockout Switch ....36 Programming Additional Transmitters .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Seat Belts And Pregnant Women ... .52 Safety Tips ......75 Seat Belt Extender .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your vehicle has the Automatic Transmission key code numbers for your vehicle locks. These numbers Place the shift lever in PARK. Turn the ignition switch to can be used to order duplicate keys from your authorized the LOCK position and remove the key.
Page 14: Locking Doors With The Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the CAUTION! shift lever in PARK, the key may become trapped tem- porarily in the ignition cylinder. If this occurs, rotate the An unlocked vehicle is an invitation to thieves.
Page 15 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses ignition keys which have an embedded someone used an invalid key to try to start the engine. electronic chip (transponder) to prevent unauthorized Either of these conditions will result in the engine being vehicle operation.
Page 16: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 starting the vehicle. Cell phones, pagers, or other RF At the time of purchase, the original owner is provided electronics will not cause interference with this system. with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location.
Page 17 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the first valid key into the ignition switch. Turn The new Sentry Key is programmed. The Remote the ignition switch to the ON position for at least three Keyless Entry transmitter will also be programmed seconds, but no longer than 15 seconds.
Page 18: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 General Information The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 19: Ignition Accessory Delay Feature
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For vehicles equipped with the Electronic Vehicle Infor- WARNING! mation Center (EVIC), the time for this feature is pro- grammable. For details, refer to “Personal Settings The key cannot be turned to LOCK until the shift (Customer-Programmable Features)”/“KEY lever is in the PARK position.
Page 20: To Set The Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Set the Alarm: To Disarm the System: The Security Alarm System will set when you use the Use the Remote Keyless Entry Transmitter to unlock the power door locks or use the Remote Keyless Entry doors.
Page 21: Illuminated Entry
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle and lock the doors with the transmitter, the alarm ILLUMINATED ENTRY will sound when you pull the door handle to exit. Vehicles Equipped With Power Door Locks NOTE: You may accidentally activate the Security All interior lights will illuminate in the vehicle when the Alarm System (horn sounds and lights flash) by entering doors are unlocked using the key fob.
Page 22: Remote Keyless Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: Your vehicle’s key fob may have three, four or REMOTE KEYLESS ENTRY five buttons (shown), depending on the optional features purchased with your vehicle. This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 ft (20 m) using a hand-held radio transmitter.
Page 23: To Lock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system can be programmed to unlock all the doors 4. Test the feature while outside of the vehicle, by upon the first UNLOCK button press by following these pressing the LOCK/UNLOCK button on the key fob. procedures: NOTE: Pressing the LOCK button on the key fob while •...
Page 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Horn Chirp Programming 5. Test the horn chirp feature while outside of the vehicle The horn chirp feature will be activated when shipped by pressing the LOCK button on the key fob with the from the assembly plants.
Page 25: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the 5. If the desired programming was not achieved or to following procedure: reactivate this feature, repeat the above steps. 1. Press and hold the UNLOCK button on the key fob. Using the Panic Alarm To activate the PANIC mode, while the ignition is OFF, 2.
Page 26: Things To Know Before Starting Your Vehicle 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Closeness to a radio transmitter, such as a radio station General Information This device complies with part 15 of FCC rules and with tower, airport transmitter, military base, and some mobile RS-210 of Industry Canada.
Page 27 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt. Fastening the seat belt will 8. Using the key fob to be programmed, press and cancel any chiming that may confuse you during this release both the LOCK and UNLOCK buttons simulta- programming procedure.
Page 28: Battery Replacement
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Battery Replacement The recommended replacement battery is CR2032. NOTE: Perchlorate Material – special handling may apply. www.dtsc.ca.gov/hazardouswaste/ perchlorate. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart.
Page 29: Remote Starting System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, snap the two halves of the case together. Make sure there is an even “gap” between the two halves. If equipped, install and tighten the screw until snug. Test transmitter operation. REMOTE STARTING SYSTEM —...
Page 30: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To enter the vehicle while the engine is running during a The vehicle can be started remotely up to a maximum of remote start, you must first unlock the vehicle using the two times.
Page 31: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave unattended children alone in a ve- hicle.
Page 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Automatic Door Locks 2. Fasten your seat belt. Fastening the seat belt will If this feature is enabled, your door locks will lock cancel any chiming that may confuse you during this automatically when the vehicle’s speed exceeds 15 mph programming procedure.
Page 33 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, performing Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when the following procedure: any door is opened (excluding the liftgate). This will 1.
Page 34: Child Protection Door Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure. Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child protection door lock system.
Page 35: Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS WARNING! Power Windows Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
Page 36: Auto Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 windows will operate only when the ignition switch is Auto Down turned to the ON position and for 10 minutes after the The driver’s and front passenger window switch has an ignition is turned OFF or the driver’s door is opened. Auto Down feature.
Page 37: Window Lockout Switch
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the window runs into any obstacle during the Resetting the Auto Up Feature auto-closure, it will reverse direction and then stop. Should the Auto Up feature stop working, the window Remove the obstacle and use the window switch again to probably needs to be reset.
Page 38: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 pressing the remote transmitter UNLOCK button prior to activating the power liftgate; otherwise, the engine will stop automatically. Window Lockout Switch LIFTGATE The liftgate can be unlocked using the Remote Keyless Power Liftgate Button Entry (RKE) Transmitter or by activating the power door Once unlocked, the liftgate can be opened or closed.
Page 39: Power Liftgate - If Equipped
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The liftgate will not manually open if the vehicle is in When the RKE Transmitter power liftgate button is gear or the vehicle speed is above 0 mph (0 km/h). pressed two times and the “Lamp Flash” feature is enabled, the turn signals will flash twice to signal that the NOTE: If the liftgate is locked and is not equipped with liftgate is opening or closing.
Page 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • There are also pinch sensors attached to the side of the WARNING! liftgate. Light pressure anywhere along these strips will cause the liftgate to return to the open position. During power operation, personal injury or cargo damage may occur.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate will not operate in temperatures WARNING! below 22°F ( 30°C) or temperatures above 150°F (65°C). Be sure to remove any buildup of snow or ice • Driving with the liftgate open can allow poison- from the liftgate before pressing any of the power ous exhaust gases into your vehicle.
Page 42: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 OCCUPANT RESTRAINTS WARNING! Some of the most important safety features in your vehicle are the restraint systems. These include the front In a collision, you and your passengers can suffer and rear seat belts for the driver and all passengers, knee much greater injuries if you are not properly buckled bolsters, front airbags for both the driver and front up.
Page 43: Lap/Shoulder Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that WARNING! they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are It is extremely dangerous to ride in a cargo area, thrown from the vehicle.
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Lap/Shoulder Belt Operating Instructions WARNING! 1. Enter the vehicle and close the door. Sit back and • Wearing a seat belt incorrectly is dangerous. Seat adjust the seat. belts are designed to go around the large bones of your body.
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE plate and pull out the belt. Slide the latch plate up the WARNING! webbing as far as necessary to allow the belt to go around your lap. • A belt buckled into the wrong buckle will not protect you properly.
Page 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, •...
Page 47: Adjustable Upper Shoulder Belt Anchorage
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Adjustable Upper Shoulder Belt Anchorage The belt will automatically retract to its stowed position. In the front and second row outboard seats, the shoulder If necessary, slide the latch plate down the webbing to belt can be adjusted upward or downward to help allow the belt to retract fully.
Page 48: Second Row Center Seat Belt
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 As a guide, if you are shorter than average you will When sitting in this seating location, ensure the seatback prefer a lower position, and if you are taller than average is fully engaged with the seatback latch by pushing you’ll prefer a higher position.
Page 49: Rear 60/40 Seat Third Row Center Three Point Belt - If Equipped
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode Rear 60/40 Seat Third Row Center Three Point Belt — If Equipped 1. Buckle the combination lap/shoulder belt. The center three point seat belt for the third row rear seat 2.
Page 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • If the small (keyed buckle) latch plate and keyed buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide the proper restraint and will increase the risk of injury in a collision.
Page 51: Seat Belt Pretensioners
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To reattach the seat belt to the third row center seat, pull the small (keyed buckle) latch plate forward from the headliner slots and insert it into the keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
Page 52: Enhanced Driver Seat Belt Reminder System (Beltalert )
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 occupant early in a collision. Pretensioners work for all triggered, the Enhanced Warning System (BeltAlert ) size occupants, including those in child restraints. will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is NOTE: These devices are not a substitute for proper seat buckled.
Page 53: Seat Belts And Pregnant Women
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or START position. DaimlerChrysler does not recom- 4. Programming mode will be cancelled after the feature mend deactivating the Enhanced Warning System has toggled with the seat belt still buckled or if the (BeltAlert ).
Page 54: Seat Belt Extender
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Keep the belt low so that it does not come across the Driver And Right Front Passenger Supplemental abdomen. That way the strong bones of the hips will take Restraint System (SRS)—Airbags the force if there is a collision.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the instrument panel, above the glove compartment. WARNING! The words SRS/AIRBAG are embossed on the airbag covers. • Do not put anything on or around the front airbag covers or attempt to manually open them. You may NOTE: The front airbags are certified to the Federal damage the airbags and you could be injured regulations that allow less forceful deployment.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: Do not use a clothing bar mounted to the coat Here are some simple steps you can follow to minimize hooks in this vehicle. A clothing bar will impede the the risk of harm from a deploying airbag. proper performance of the window bags.
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. If your vehicle has window bags, do not lean against WARNING! the door or window. Airbags will inflate forcefully into the space between you and the door. • Relying on the airbags alone could lead to more severe injuries in a collision.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Driver and Front Passenger Seat Belt Pretensioners Airbag System Components The airbag system consists of the following: How the Airbag System Works • Occupant Restraint Controller • The Occupant Restraint Controller (ORC) determines •...
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are Also, the ORC turns on the AIRBAG warning light in the instrument cluster for six to eight located in the center of the steering wheel and the right seconds for a self-check when the ignition is side of the instrument panel.
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • The Side Impact SRS Window Bags are designed to NOTE: At no time should any Supplemental Restraint activate only in certain side collisions or in a roll over System (SRS) component or SRS-related component or event.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any irritation continues, see your doctor. If these particles or all of the following may occur: settle on your clothing, follow the garment manufac- turer’s instructions for cleaning.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Maintaining Your Airbag System NOTE: Perchlorate Material – special handling may ap- ply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. WARNING! Enhanced Accident Response System If the airbags deploy after an impact and the electrical • Modifications to any part of the airbag system system remains functional, vehicles equipped with could cause it to fail when you need it.
Page 63: Event Data Recorder (Edr)
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag light does not come on or flickers during Event Data Recorder (EDR) the six to eight seconds when the ignition switch is In the event of an accident, your vehicle is designed to first turned on.
Page 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 DaimlerChrysler Corporation, such investigations may nature, such as would identify a particular driver, ve- be requested by customers, insurance carriers, govern- hicle, or crash, will be treated confidentially. Confidential ment officials, and professional crash researchers, such as data will not be disclosed by DaimlerChrysler those associated with universities, and with hospital and Corporation to any third party except when:...
Page 65: Child Restraint
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag disable lamp status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the • Time of airbag deployment (in terms of ignition time - babies and children, too. Every state in the United cycles and vehicle mileage) States and all Canadian provinces require that small •...
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 babies at the right front passenger seat position. If a car LATCH child restraint anchorage system. (Refer to bed must be used to transport a newborn baby, the car “LATCH - Child Seat Anchorage System” in this bed must be installed in the second seating row only.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit slouching can move the belt out of position. the vehicle’s seat belts properly.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Here are some tips for getting the most out of your child around the child restraint so that it is not necessary to restraint: use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the •...
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When your child restraint is not in use, secure it in the and hooks for connection to the top tether anchorages vehicle with the seat belt or remove it from the vehicle. have been available for some time.
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 only install the child restraints using the vehicle’s seat belts. Refer to “Installing the LATCH-Compatible Child Restraint System” this section. Second Row Seat Right Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the Second Row Seat Left Side manufacturer when installing your child restraint.
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE were provided with the child restraint system. The rear anchorages. Next, attach the lower hooks or connectors seat lower anchorages are round bars, located at the rear over the top of the anchorage bars, pushing aside the seat of the seat cushion where it meets the seatback, and are cover material.
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 reach. If the buckled seat belt interferes with the child Installing Child Restraints Using the Vehicle Seat restraint installation, instead of tucking the seat belt Belt behind the child restraint, route the seat belt through the The second and third row seats have either cinching latch child restraint belt path and then buckle it.
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE pulling on the excess webbing to tighten the lap portion Child Restraints in Third Row Seating (If around the child restraint. Refer to Automatic Locking Equipped) Mode in this section. For vehicles equipped with third row split bench (60/40) seating, the tether strap anchorage is located on the seatback behind the center seating position.
Page 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Child Restraint Tether Anchor There are tether strap anchorages behind each seating position in the second row and behind the center seating position in the case of the third row seat (60/40) split bench, if equipped.
Page 75: Engine Break-In Recommendations
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 An incorrectly anchored tether strap could lead to mi (500 km).
Page 76: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 A new engine may consume some oil during its first few SAFETY TIPS thousand miles (kilometers) of operation. This is a nor- Exhaust System mal part of the break-in and is not an indication of difficulty.
Page 77: Safety Checks You Should Make Inside The Vehicle
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Be aware of changes in the sound of the exhaust system, Seat Belts exhaust fumes detected inside the vehicle, or damage to Inspect the belt system periodically, checking for cuts, the underside or rear of the vehicle. Have a competent frays and loose parts.
Page 78: Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Door Latches Safety Checks You Should Make Outside The Vehicle Check for positive closing, latching and locking. Tires Fluid Leaks Examine tires for tread wear or uneven wear patterns. Check area under vehicle after overnight parking for fuel, Check for stones, nails, glass or other objects lodged in water, oil, or other fluid leaks.
Page 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......84 Automatic Dimming Driver’s Exterior Mirror — If Equipped .
Page 81 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information ....115 4-Way Passenger’s Power Seat — If Equipped ......124 Voice Recognition System (VR) —...
Page 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Self-Limiting Control ....141 Multifunction Control Lever ....149 Driver Easy Exit And Easy Entry Control .
Page 83 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing ....159 Using HomeLink ..... 181 Rear Park Assist System —...
Page 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Floor Console ......189 Factory Installed Roof Luggage Rack ..192 Front Floor Console Features .
Page 85: Mirrors
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Annoying headlight glare can be reduced by moving the small control under the mirror to the NIGHT position Inside Day/Night Mirror (toward the rear of vehicle). The mirror should be ad- The mirror should be adjusted to center on the view justed while set in the DAY position (toward the wind- through the rear window.
Page 86: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
Page 87: Electric Remote-Control Mirrors
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. Mirror Directions To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
Page 88: Illuminated Vanity Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object.
Page 89: Automatic Dimming Driver's Exterior Mirror - If Equipped
IF EQUIPPED following websites: NOTE: The sales code RER radio contains an inte- • www.chrysler.com/uconnect grated Hands-Free Communication (UConnect ) sys- tem. Refer to your “Navigation User’s Manual” for • www.dodge.com/uconnect UConnect system operating instructions for this radio.
Page 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 UConnect allows you to transfer calls between the system at a time. The system is available in English, system and your cellular phone as you enter or exit your Spanish, or French languages (as equipped). vehicle and enables you to mute the system’s microphone PHONE Button for private conversation.
Page 91: Operation
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for Profile) you may not be able to use any UConnect features. Refer to your cellular service provider or the the beep, which follows the Ready prompt or another phone manufacturer for details.
Page 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Voice Command Tree Pair (Link) UConnect System to a Cellular Phone Refer to “Voice Tree” in this section. To begin using your UConnect system, you must pair your compatible Bluetooth enabled cellular phone. Help Command If you need assistance at any prompt, or if you want to To complete the pairing process, you will need to refer-...
Page 93 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE enter into your cellular phone. You can enter any make a call. You can select to use a lower priority four-digit PIN number. You will not need to remember cellular phone at any time (refer to Advanced Phone this PIN number after the initial pairing process.
Page 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • The UConnect system will confirm the phone num- • The UConnect system will confirm the name and ber and then dial. The number will appear in the then dial the corresponding phone number, which display of certain radios.
Page 95 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., Phonebook Download Home, Work, Mobile, or Pager ). This will allow UConnect allows the user to download entries from you to store multiple numbers for each phonebook their phone via Bluetooth .
Page 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • When prompted, recite the new phone number for the the UConnect system, and then send the address book entry via Bluetooth . Please see your phone phonebook entry that you are editing. owner’s manual for specific instructions on how to After you are finished editing an entry in the phonebook, drop the Bluetooth connection.
Page 97 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Delete All Entries in the UConnect Phonebook Phonebook Delete. • Press the PHONE button to begin. • After you enter the Phonebook Delete menu, you will •...
Page 98: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • The UConnect system will play the names of all the accessed through the UConnect system. Check with phonebook entries. your cellular service provider for the features that you have. • To call one of the names in the list, press the “Voice Recognition”...
Page 99 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE call waiting that you normally hear when using your cell Place/Retrieve a Call From Hold phone. Press the PHONE button to place the current call To put a call on hold, press the PHONE button until you on hold and answer the incoming call.
Page 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • After the Ready prompt and the following beep, say Three-Way Calling To initiate three-way calling, press the “Voice Recogni- Redial. tion” button while a call is in progress, and make a • The UConnect system will call the last number that second phone call, as described under Making a Second was dialed from your cellular phone.
Page 101: Uconnect System Features
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can After selecting one of the languages, all prompts and continue on the UConnect system for a certain dura- voice commands will be in that language. tion, after which the call is automatically transferred NOTE: After every UConnect language change opera- from the UConnect system to the mobile phone.
Page 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • After the Ready prompt and the following beep, say Towing Assistance Emergency and the UConnect system will instruct If you need towing assistance: the paired cellular phone to call the emergency num- •...
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to sequence on your cellular phone keypad, you can press work properly with the UConnect system. the “Voice Recognition” button and say the sequence you wish to enter, followed by the word Send.
Page 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Press the PHONE button to begin. NOTE: • You may not hear all of the tones due to cellular phone • After the Ready prompt and the following beep, say network configurations; this is normal. Setup Confirmations.
Page 105: Advanced Phone Connectivity
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE dialing a number with your paired Bluetooth cellular In order to un-mute the UConnect system: phone, the audio will be played through your vehicle’s • Press the “Voice Recognition” button. audio system. The UConnect system will work the same •...
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 If you would like to connect or disconnect the Bluetooth Select Another Cellular Phone connection between a UConnect paired cellular phone This feature allows you to select and start using another and the UConnect system, follow the instructions de- phone paired with the UConnect system.
Page 107: Things You Should Know About Your Uconnect System
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect Paired Cellular Phones Voice Training For users experiencing difficulty with the system recog- • Press the PHONE button to begin. nizing their voice commands or numbers, the UConnect • After the Ready prompt and the following beep, say system Voice Training feature may be used.
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • Performance is maximized under: This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • low-to-medium blower setting, To restore the voice recognition system to factory default •...
Page 109 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding • low-to-medium vehicle speed, names in the UConnect phonebook. • low road noise, • The UConnect phonebook nametag recognition rate • smooth road surface, is optimized for the person who stored the name in the •...
Page 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Bluetooth Communication Link Power-Up Cellular phones have been found to lose connection to After switching the ignition key from OFF to either ON the UConnect system. When this happens, the connec- or ACC position, or after a language change, you must tion can generally be re-established by switching the wait at least five seconds prior to using the system.
Page 111 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111...
Page 113 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 116: Understanding The Features Of Your Vehicle 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: In a stressful situation, take care to speak into General Information This device complies with part 15 of the FCC rules and the Voice Interface System as calmly and normally as RSS 210 of Industry Canada. Operation is subject to the possible.
Page 117: Commands
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the VR hard-key, listen for the beep, and dows are closed, and the heater/air-conditioning fan is say your command.
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • NEXT STATION (to select the next station) 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition • PREVIOUS STATION (to select the previous station) system is speaking.
Page 119 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio Disc To switch to satellite radio mode say SAT or SATELLITE To switch to the disc mode say DISC. In this mode, you RADIO. In this mode, you may say the following com- may say the following commands: mands: •...
Page 120: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 − CONTINUE (to continue recording) Voice Training For users experiencing difficulty with the system recog- − DELETE (to delete the recording) nizing their voice commands or numbers, the UConnect • PLAY MEMOS (to play previously recorded memos) system Voice Training feature may be used.
Page 121: Seats
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
Page 122: Front Seat Manual Seat Recliners
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 lifting the lever, then push back to the desired position WARNING! and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body Adjusting a seat while the vehicle is moving is pressure, lean forward and rearward on the seat to be dangerous.
Page 123: Manual Lumbar Support Adjustment - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment — If Adjustable Head Restraints — All Seating Equipped Positions The manual lumbar support adjustment lever is located Head restraints can reduce the risk of whiplash injury in on the right side of the driver’s seat and on the left side the event of impact from the rear.
Page 124: 8-Way Driver's Power Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 8-Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the left side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment.
Page 125: 4-Way Passenger's Power Seat - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4-Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. NOTE: The 4-way seat does not have an up/down adjustment.
Page 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 With the ignition switch in the RUN position, depressing the heated seat switch rocker to its momentary high or low position provides power to the heated seat element and maintains the requested temperature setting. If the heated seat switch is depressed to a different position (low or high) than the currently selected state, the re- quested temperature setting will change to a new selec-...
Page 127 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE off. Both of the indicators on identifies High heat level. WARNING! The lower indicator on only identifies Low heat level. Persons who are unable to feel pain to the skin NOTE: The HI heat setting will operate for approxi- because of advanced age, chronic illness, diabetes, mately 30 minutes.
Page 128: Second Row Bucket Seats - Fold And Tumble
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3. Pull up on the seatback release lever located on the Second Row Bucket Seats — Fold and Tumble Second row bucket seats have seatback recliners on both outboard side of the seat and push the seatback forward. seating positions.
Page 129 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pull up on the release handle and lift to tumble the To relatch the seat, tilt the seat rearward and push down seat fully forward. If the seat contacts the rear of the front firmly to engage the rear attachments.
Page 130: Second Row 40/20/40 Seat - Fold And Tumble
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Second Row 40/20/40 Seat — Fold and Tumble The 40/20/40 seat configuration is standard on all mod- els.
Page 131 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second row leather seats have seatback recliners at the To fold the 40% seatbacks, fully raise the lever on the side 40% seating positions. Raising the lever allows the seat- of the seat to release the seatback. The seatback can now back to be reclined an additional 11 degrees.
Page 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 To fold the 20% seatback, pull the strap forward to release the seatback. Fold the seatback down for use as an armrest or to carry cargo. When returning the seatback to the upright position, push the seatback rearward to latch the seatback.
Page 133 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position. The outer 40% second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
Page 134: Third Row Seat Bench - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Third Row Seat Bench — If Equipped To Fold the Seats Folding the third seat occurs in two stages: First, the cushion is lifted and moved forward from the pockets at the front of the cushion. The cushion will rest on the floor directly behind the second row seat.
Page 135 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seat Cushion Movement Up And Forward Third Row Seat Folded Forward CAUTION! When loading cargo into the rear of your vehicle with the third row seat folded flat, be careful not to damage the material on the head restraints.
Page 136: Third Row 60/40 Folding - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: The seat belt buckles are hinged to fold with the Third Row 60/40 Folding — If Equipped seatback. WARNING! Do not sit in the third row seat unless the cushion and back are properly engaged. Proper engagement can be verified by pushing/pulling on the upright seatback.
Page 137 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seat 40% Seatback Fold Third Row Seat Features...
Page 138: Driver Memory System - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Third Row Seat Folded Forward Third Row Seat Return Pull Strap DRIVER MEMORY SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic Tem- perature Control (ATC) temperature and radio station...
Page 139: Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE preset settings. Your Remote Keyless Entry (RKE) Trans- position. The memory system can accommodate up to mitters can also be programmed to recall the same two transmitters, each transmitter linked to either of the positions when the UNLOCK button is pressed.
Page 140: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 3. Turn on the radio and set the radio station presets (up 9. Repeat the above steps to set the next memory posi- to 10 AM and 10 FM stations can be set). tion using the other numbered memory button or to link another RKE Transmitter to memory.
Page 141: To Disable A Transmitter Linked To Memory
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press NOTE: A chime sound may be heard if Setting Memory memory button number 1 on the driver’s door or the was inhibited for any reason. UNLOCK button on the Remote Keyless Entry Transmit- To Disable A Transmitter Linked to Memory ter linked to memory position 1.
Page 142: Self-Limiting Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 with the Electronic vehicle Information Center (EVIC), the same button or buttons. Continued seat travel beyond refer to “Personal Settings (Customer Programmable the obstructed position will indicate the recently encoun- Features)” under “Overhead Console with Electronic tered self-limitation has been cleared.
Page 143: To Open And Close The Hood
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the Electronic Vehicle Information Center (EVIC). For details, refer to “Personal Settings (Customer Program- mable Features)” under “Overhead Console with Elec- tronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
Page 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Then push the safety latch lever to the left. It is located To prevent possible damage, do not slam the hood to between the grille and hood opening right of the center. close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage.
Page 145: Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch Headlight Switch Location...
Page 146: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 and the interior lights are on, rotating the dimmer control Interior Lights all of the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
Page 147: Headlight Delay
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the ignition is off and any door is left ajar for eight Headlight Delay minutes or the dimmer control is rotated upwards for 15 To aid in your exit, your vehicle is equipped with a minutes, the interior lights will automatically turn off.
Page 148: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Plastic is not as scratch resistant as glass and therefore Automatic Headlights — If Equipped Automatic headlights can be activated by rotating the different lens cleaning procedures must be followed. rotary headlight switch to the symbol “A.” The head- To minimize the possibility of scratching the lenses and lights will turn on when the engine is running and the reducing light output, avoid wiping with a dry cloth.
Page 149: Daytime Running Lights (Canada Only)
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) Fog Lights — If Equipped The headlights on your vehicle will illuminate when the engine is started. This provides a constant “Lights ON” condition until the ignition is turned OFF. The lights illuminate at reduced intensity.
Page 150: Multifunction Control Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 light located in the instrument cluster will illuminate The arrow on either side of the instrument cluster flashes when the fog lights are on. The fog lights will turn off to indicate the direction of the turn, and proper operation when the switch is pressed in, when the headlight switch of the front and rear turn signal lights.
Page 151 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If a turn signal has been left on for at least a mile Turn Signal Auto-Mode (a kilometer), a continuous chime will sound. Tap the multifunction control lever once and the turn signal (left or right) will flash three times, and automati- cally turn off.
Page 152: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 High Beam/Low Beam Select Switch WINDSHIELD WIPERS AND WASHERS Pull the multifunction control lever fully toward the Windshield Wipers steering wheel to switch the headlights from high or low beam. Windshield Wiper Switch The wipers and washers are operated by a switch in the Dimmer Lever multifunction control lever.
Page 153 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System WARNING! The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, Sudden loss of visibility through the windshield with a variable pause between cycles, desirable. For could lead to an accident.
Page 154: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
Page 155: Tilt Steering Column
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN WARNING! To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as Tilting the steering column while the vehicle is desired.
Page 156: Driver Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2.
Page 157: Electronic Speed Control - If Equipped
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 158: To Set At A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 can be reactivated by pushing the speed control switch WARNING! ON/OFF button and re-establishing the desired vehicle SET speed. Leaving the Speed Control on when not in use is dangerous. You could accidentally set the system to Push the ON/OFF button to the ON position.
Page 159: To Vary The Speed Setting
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting Tapping the DECEL button once will result in a speed When the speed control is on, speed can be increased by decrease (refer to the following table for the speed for pressing and holding the RESUME/ACCEL button.
Page 160: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Vehicles equipped with an automatic transmission may To Accelerate For Passing Depress the accelerator as you would normally. When the exhibit several downshifts under the above conditions. pedal is released, the vehicle will return to the set speed. To reduce the frequency of the downshifts and to im- prove vehicle performance, it is advisable to lock out NOTE: When driving uphill, at elevations above 2,000 ft...
Page 161: Rear Park Assist System - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM — IF EQUIPPED NOTE: The manufacturer suggests disabling the Rear Park Assist System when towing a trailer. Refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Infor- mation Center (EVIC) –...
Page 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 The system dimly illuminates the two outermost yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM: LED COLOR...
Page 163 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Drivers must be careful when backing up, even when • The Rear Park Assist System is only a parking aid using the Rear Park Assist System. Always check and it is unable to recognize every obstacle, in- carefully behind your vehicle, look behind you, and cluding small obstacles.
Page 164: Rear Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: REAR CAMERA — IF EQUIPPED • Ensure that the rear bumper is free of dirt and debris Your vehicle may be equipped with a Rear Camera to keep the system operating properly. system that allows you to see an on-screen image (located in the screen of your Radio) of the rear of your vehicle •...
Page 165 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The camera view will display only while the WARNING! vehicle is in REVERSE. Drivers must be careful when backing up even when 4. Perform a visual check of the rear area. using the Rear Camera System. Always check care- NOTE: CHECK ENTIRE SURROUNDINGS before fully behind your vehicle, and be sure to check for...
Page 166: Overhead Console
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 OVERHEAD CONSOLE CAUTION! The overhead console has the following features: • To avoid vehicle damage, the Rear Camera System should only be used as a parking aid and is unable to view every obstacle or object in your drive path. •...
Page 167: Courtesy/Reading Lights
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Electronic Vehicle Information Center (EVIC) — If OVERHEAD CONSOLE WITH ELECTRONIC Equipped VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED Courtesy/Reading Lights The overhead console contains dome/reading lights, and Near the front of the console is one courtesy and two an Electronic Vehicle Information Center (EVIC).
Page 168: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Trip Functions Electronic Vehicle Information Center (EVIC) — If Equipped Pressing the STEP button allows you to scroll through one of the following Trip Function features: • TRIP – Shows the total distance traveled since the last reset.
Page 169 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE before the reset. (Example: If your EVIC displays 18 NOTE: Significant changes in driving style or vehicle AVG. MPG and the RESET button is pressed, the loading will greatly affect the actual drivable distance of previous averaging history will be erased and the the vehicle, regardless of the DTE displayed value.
Page 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • TURN SIGNALS ON (with a continuous warning • LIFTGATE OPEN chime) • CHECK TPM SYSTEM (with single chime) (Premium • PERSONAL SETTINGS NOT AVAILABLE – Vehicle TPM System Only) not in PARK OIL CHANGE REQUIRED —...
Page 171 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the ignition switch to the ON position (Do not Press and release the MENU button until the Personal Settings displays on the EVIC. start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds.
Page 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 stopped and the transmission is in the PARK or will recall the memory settings for the seat, mirror and NEUTRAL position and the driver’s door is opened. radio. To make your selection, press and release the To make your selection, press and release the RESET RESET button until “ON or “OFF”...
Page 173 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “HEADLAMP OFF DELAY > 0 SEC” – When this • “KEY OFF POWER DELAY> OFF” – When this feature feature is selected, the driver can choose to have the is selected, the power window switches, radio, hands– headlamps remain on for 0, 30, 60, or 90 seconds when free system (if equipped), and power outlets will exiting the vehicle.
Page 174: Compass/Temperature Button
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • “UNIT IN > U.S./METRIC” – The EVIC odometer can Compass/Temperature Button be changed between English and Metric units of Pressing the Compass/Temperature button measure. To make your selection, press and release the will return the display to the normal compass/ RESET button until “US”...
Page 175 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration 5. Slowly drive the vehicle at a speed of 5 mph (8 km/h) If the compass appears erratic and the “CAL” message in a complete 360°circle, (in an area free from large does not appear in the EVIC display, you must put the metal or metallic objects) until the “CAL”...
Page 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 1. Turn the ignition switch to the ON/RUN position. 2. Press the MENU button until “Personal Settings” is displayed. 3. Press the STEP button until “Compass Variance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the variance map.
Page 177: Garage Door Opener - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink unit operates off your vehicle’s battery.
Page 178: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! WARNING! Your motorized door or gate will open and close Vehicle exhaust contains carbon monoxide, a danger- while you are training the Universal Transceiver. Do ous gas. Do not run your vehicle in the garage while not train the transceiver if people or pets are in the training the transceiver.
Page 179 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE It is recommended that a new battery be placed in the Then release both the HomeLink and hand-held trans- hand-held transmitter of the device being programmed mitter buttons. to HomeLink for more efficient training and accurate If the EVIC display states “DID NOT TRAIN”...
Page 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: After training a HomeLink channel, if the garage door does not operate with HomeLink and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.”...
Page 181: Gate Operator/Canadian Programming
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed Similar to this Canadian law, some U.S. gate operators are HomeLink button twice (holding the button for two designed to “time-out” in the same manner. seconds each time).
Page 182: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Using HomeLink Security To operate, simply press and release the programmed It is advised to erase all channels before you sell or turn HomeLink button. Activation will now occur for the in your vehicle. trained device (i.e., garage door opener, gate operator, To do this, press and hold the two outside buttons for 20 security system, entry door lock, home/office lighting,...
Page 183: General Information
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Did you unplug the device for training, and remember expressly approved by the party responsible for compli- to plug it back in? ance could void the user’s authority to operate the device. If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at The term “IC:”...
Page 184: Express Open Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 the panel is venting, pressing the “close” end of the condition until the switch is pushed forward again. To rocker switch returns it to the closed position. Both close fully, hold the switch in the forward position until opening and closing operations in the vent mode occur the glass movement has stopped.
Page 185: Wind Buffeting
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting WARNING! Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the In an accident, there is a greater risk of being thrown ears.
Page 186: Electrical Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 (switched battery fed) or with the ignition ON or OFF ELECTRICAL POWER OUTLETS This vehicle has three auxiliary power outlets that can (battery fed) to allow for cellular telephone charging and provide up to 20 Amps of current for accessories de- or operation while the ignition is off.
Page 187 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When the inverter switch is pressed, there will NOTE: Due to build-in overload protection the inverter be a delay of approximately one second before the will shut down if the power rating is exceeded. inverter status indicator turns ON.
Page 188: Electrical Outlet Use With Engine Off (Battery Fed Configuration)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 189 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reconfiguring Power Outlets To reconfigure the outlets, be sure the ignition is OFF before removing the fuse. The reconfigurable fuse loca- tion is a special design that allows the fuse to be installed in two different ways.
Page 190: Floor Console
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 • Removable CD bin FLOOR CONSOLE • 115 V Inverter Plug Front Floor Console Features The floor console between the driver’s and front passen- • RCA Jacks ger’s seat, has the following features: The coin slots are located under the instrument panel •...
Page 191 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In colder temperatures you may experience a slight delay on console doors opening; the console door speed will come back to normal after 1–2 cycles. Front Center Console The front storage bin in the center console is equipped with a removable bin mat.
Page 192: Rear Floor Console Features - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 being stored in the bin. To use, plug in the portable power recharge cord and place the cord along the opening under the forward portion of the storage bin. Close the console armrest lid and plug the power cord into the phone while resting the phone in the bin.
Page 193: Factory Installed Roof Luggage Rack
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Tissue holder and pen holder FACTORY INSTALLED ROOF LUGGAGE RACK • Second row heated seat switches • Four slots for DVDs Roof Luggage Rack The load carried on the roof when equipped with a luggage rack must not exceed 150 lbs (68 kg), and should Rear Floor Console be uniformly distributed over the cargo area.
Page 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 The side rails between the stantions should be used to tie CAUTION! down cargo. Check the straps frequently to be sure that the load remains securely attached. To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.
Page 195: Cargo Management System-If Equipped
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.
Page 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Side Cover 1 - Cargo Divider Door 2 - Cargo Divider Side Panel To open the main cover, pull up on the latch, and attach the cord to the rear seat head restraint post. To remove the cargo management system from the ve- hicle, pull the right-hand side of the organizer toward To open the cargo divider, lift up on the cargo divider...
Page 198: Instrument Panel And Controls
INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....201 Electrical Disturbances ....216 Instrument Cluster .
Page 199 198 INSTRUMENT PANEL AND CONTROLS Operating Instructions — Hands-Free List Button (CD Mode For MP3 Play) ..235 Communication (UConnect ) (If Equipped) . . . 218 Info Button (CD Mode For MP3 Play) ..235 Clock Setting Procedure .
Page 200 INSTRUMENT PANEL AND CONTROLS 199 Operating Instructions - Video Entertainment Left-Hand Switch Functions For Media System (VES™) (If Equipped) ... . . 241 (i.e., CD) Operation ....247 Universal Consumer Interface (UCI) —...
Page 201 200 INSTRUMENT PANEL AND CONTROLS Automatic Control ....254 Operating Tips ..... . . 261 Level Of Automatic Control .
Page 202: Instruments And Controls
INSTRUMENT PANEL AND CONTROLS 201 INSTRUMENTS AND CONTROLS...
Page 203: Instrument Cluster
202 INSTRUMENT PANEL AND CONTROLS Instrument Cluster...
Page 204: Instrument Cluster Description
INSTRUMENT PANEL AND CONTROLS 203 INSTRUMENT CLUSTER DESCRIPTION CAUTION! 1. Fuel Gage Do not leave your vehicle unattended with the en- The fuel gage shows level of fuel in the tank when gine running as you would not be able to react to the ignition switch is in the ON position.
Page 205 204 INSTRUMENT PANEL AND CONTROLS left/right turn signal is left on with the engine RPM 7. Coolant Temperature Light vehicle speed greater than 15 mph (24 km/h) for more This light warns of an overheated engine condi- than one mile. tion.
Page 206 INSTRUMENT PANEL AND CONTROLS 205 10. Security Light WARNING! This light will flash rapidly for approximately 15 seconds when the Vehicle Security Alarm is arming. The light will A hot engine cooling system is dangerous. You or flash at a slower speed continuously after the alarm is set. others could be badly burned by steam or boiling The Security light will also come on for about three coolant.
Page 207 206 INSTRUMENT PANEL AND CONTROLS charging voltage falls below 10 volts, the malfunction 14. Gear Selector indicator light illuminates and the ABS is switched off. The electronic gear selector display is self-contained When the voltage is above this value again, the malfunc- within the instrument cluster.
Page 208 INSTRUMENT PANEL AND CONTROLS 207 The two trip odometers show individual trip mileage. To NOTE: If the vehicle is equipped with an EVIC, most switch from odometer to trip odometers, press and warnings will display in the EVIC. For additional infor- release the Trip Odometer button.
Page 209 208 INSTRUMENT PANEL AND CONTROLS Unless reset, this message will continue to display each 16. Odometer time you turn the ignition switch to the ON/RUN The odometer shows the total distance the vehicle has position. To turn off the message temporarily, press and been driven.
Page 210 INSTRUMENT PANEL AND CONTROLS 209 ESP/TCS indicator light starts to flash as soon as the tires 20. Electronic Throttle Control (ETC) lose traction and the ESP system becomes active. The This light informs you of a problem with the ESP/TCS indicator light also flashes when TCS is active. Electronic Throttle Control system.
Page 211 210 INSTRUMENT PANEL AND CONTROLS have the bulb repaired promptly. If the light stays on, it 22. ESP/BAS Warning Lamp may be an indication that the parking brake has not been The malfunction lamp for the ESP is combined released, or there is a low brake fluid level. If the light with BAS.
Page 212 INSTRUMENT PANEL AND CONTROLS 211 23. Malfunction Indicator Light (MIL) Although your vehicle will usually be drivable and not This light is part of an onboard diagnostic system need towing, see your authorized dealer for service as which monitors the emissions and engine control soon as possible.
Page 213 212 INSTRUMENT PANEL AND CONTROLS by the vehicle manufacturer on the vehicle placard or tire maintain correct tire pressure, even if under-inflation has inflation pressure label. (If your vehicle has tires of a not reached the level to trigger illumination of the TPMS different size than the size indicated on the vehicle low tire pressure telltale.
Page 214 INSTRUMENT PANEL AND CONTROLS 213 tires or wheels on your vehicle to ensure that the replace- 25. Airbag Indicator ment or alternate tires and wheels allow the TPMS to The indicator lights and remains lit for six to continue to function properly. eight seconds when the ignition is first turned ON.
Page 215: Electronic Digital Clock
214 INSTRUMENT PANEL AND CONTROLS 28. Cruise Light (Speed Control) ELECTRONIC DIGITAL CLOCK This indicator lights when the electronic speed control The clock and radio each use the display panel built into system is turned on. the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio 29.
Page 216: Clock Setting Procedure
INSTRUMENT PANEL AND CONTROLS 215 Clock Setting Procedure SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument 1. Press and hold the TIME button until the hours blink. panel, press and hold the button until the setting is 2.
Page 217: Radio General Information
216 INSTRUMENT PANEL AND CONTROLS RADIO GENERAL INFORMATION Electrical Disturbances Radio waves may pick up electrical disturbances during Radio Broadcast Signals transmission. They mainly affect the wave amplitude, The radio will provide excellent reception under most and thus remain a part of the AM reception. They operating conditions.
Page 218: Sales Code Ren - Multimedia System - If Equipped
INSTRUMENT PANEL AND CONTROLS 217 NOTE: The radio, steering wheel radio controls (if An auxiliary input jack permits passengers to listen to a equipped), and 6–Disc CD/DVD changer (if equipped) portable MP3 player through the vehicle’s speakers. For will remain active for up to 10 minutes after the ignition vehicles equipped with the Vehicle Entertainment System switch has been turned OFF.
Page 219: Operating Instructions - Satellite Radio (If Equipped)
218 INSTRUMENT PANEL AND CONTROLS Operating Instructions — Satellite Radio (If Clock Setting Procedure Equipped) Setting the Clock Refer to your Radio-specific user’s manual for detailed operating instructions. 1. Turn on the multimedia system. Operating Instructions — Voice Recognition 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen.
Page 220 INSTRUMENT PANEL AND CONTROLS 219 5. To save the new time setting, touch the screen where Show Time if Radio is Off the word “Save” is displayed. When selected, this feature will display the time of day on the touch screen when the multimedia system is Changing Daylight Savings Time turned off.
Page 221: Sales Code Rer - Multimedia System - If Equipped
220 INSTRUMENT PANEL AND CONTROLS 3. Touch the screen where the words “Set Time Zone” are NOTE: If your vehicle is not equipped with UConnect , displayed. The time zone selection menu will appear on the unit will respond with a “Feature Not Available” the screen.
Page 222: Operating Instructions - Satellite Radio
INSTRUMENT PANEL AND CONTROLS 221 An auxiliary input jack permits passengers to listen to a Operating Instructions — Satellite Radio portable MP3 player through the vehicle’s speakers. For Refer to your “Navigation User’s Manual” for detailed vehicles equipped with the Vehicle Entertainment System operating instructions.
Page 223 222 INSTRUMENT PANEL AND CONTROLS 2. Touch the screen where the time is displayed. The Changing Daylight Savings Time clock setting menu will appear on the screen. If the words When selected, this feature will display the time of day in “Time: GPS Time”...
Page 224 INSTRUMENT PANEL AND CONTROLS 223 2. Touch the screen where the time is displayed. The 6. To save the new time setting, touch the screen where clock setting menu will appear on the screen. If the words the word “Save” is displayed. “Time: User Clock”...
Page 225: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
224 INSTRUMENT PANEL AND CONTROLS SALES CODE RES — AM/FM STEREO RADIO Operating Instructions - Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 226 INSTRUMENT PANEL AND CONTROLS 225 to seek up and the left switch to seek down. The radio If your vehicle is not equipped with this or this feature is will remain tuned to the new station until you make not available on your vehicle, a “Not Equipped With another selection.
Page 227 226 INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button, until the hours blink. procedure, starting at Step 2. 2.
Page 228 INSTRUMENT PANEL AND CONTROLS 227 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between the right or left to increase or decrease the bass tones.
Page 229 228 INSTRUMENT PANEL AND CONTROLS Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display 16-Digit Character Personality Persnlty Program Type Display Public Public No program type or un- Rhythm and Blues R & B None defined Religious Music...
Page 230 INSTRUMENT PANEL AND CONTROLS 229 By pressing the SEEK button when the Music Type icon AM and FM Buttons is displayed, the radio will be tuned to the next frequency Press the buttons to select AM or FM modes. station with the same selected Music Type name. The SET Button —...
Page 231: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
230 INSTRUMENT PANEL AND CONTROLS Every time a preset button is used, a corresponding Inserting Compact Disc(s) button number will display. Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into Buttons 1 - 6 the CD player and the CD icon will illuminate on the These buttons tune the radio to the stations that you...
Page 232 INSTRUMENT PANEL AND CONTROLS 231 If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. •...
Page 233: Notes On Playing Mp3 Files
232 INSTRUMENT PANEL AND CONTROLS TIME Button Press the right SEEK button to move to the next ran- Press this button to change the display from a large CD domly selected track. playing time display to a small CD playing time display. Press the RND button a second time to stop Random Play.
Page 234 INSTRUMENT PANEL AND CONTROLS 233 • Level 2: 31 (including a separator . and a three- files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. character extension) The radio uses the following limits for file systems: Multisession disc formats are supported by the radio.
Page 235 234 INSTRUMENT PANEL AND CONTROLS rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rates.
Page 236: List Button (Cd Mode For Mp3 Play)
INSTRUMENT PANEL AND CONTROLS 235 Press and hold the INFO button again for three seconds LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 237: Satellite Radio (Rsc) - If Equipped (Rer/Req/Ren Radios Only)
236 INSTRUMENT PANEL AND CONTROLS TIME Button (Auxiliary Mode) SATELLITE RADIO (RSC) — IF EQUIPPED Press this button to change the display to time of day. The (RER/REQ/REN RADIOS ONLY) time of day will display for five seconds (when ignition is Satellite radio uses direct satellite-to-receiver broadcast- OFF).
Page 238: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
INSTRUMENT PANEL AND CONTROLS 237 call the toll-free number 888-539-7474, or visit the Sirius selected. Press the TUNE/SCROLL control knob and the web site at www.sirius.com, or at www.siriuscanada.ca Sirius ID number will display. The Sirius ID number for Canadian residents. Please have the following infor- display will time out in two minutes.
Page 239: Satellite Antenna
238 INSTRUMENT PANEL AND CONTROLS • Driving under wide bridges or along tall buildings can Satellite Antenna To ensure optimum reception, do not place items on the cause intermittent reception. roof around the rooftop antenna location or strap items to •...
Page 240 INSTRUMENT PANEL AND CONTROLS 239 SCAN Button TUNE Control (Rotary) Pressing the SCAN button causes the tuner to search for Turn the rotary TUNE/SCROLL control knob clockwise the next channel, pausing for eight seconds before con- to increase or counterclockwise to decrease the channel. tinuing to the next.
Page 241 240 INSTRUMENT PANEL AND CONTROLS SETUP Button You may add a second channel to each pushbutton by Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press following items: the SET button twice and SET 2 will show in the display window.
Page 242: Equipped)
INSTRUMENT PANEL AND CONTROLS 241 This feature allows you to plug an iPod mobile digital Operating Instructions - Hands-Free Phone (If Equipped) device into the vehicle’s sound system through a connec- Refer to “Hands-Free Communication (UConnect )” in tor (UCI connector) using an optional connection cable Section 3.
Page 243: Connecting The Ipod Device
242 INSTRUMENT PANEL AND CONTROLS Connecting The iPod Device Play Mode Use the optional connection cable to connect an iPod to When switched to UCI mode the iPod will be in Play the vehicle’s UCI connector (which is located in the glove mode.
Page 244 INSTRUMENT PANEL AND CONTROLS 243 RW (Rewind) Button If the left (down) button is pressed during the first two Press and hold the RW button to move backward in the seconds of the current track, it will go back to the current track.
Page 245: List Or Browse Mode
244 INSTRUMENT PANEL AND CONTROLS SCAN Button TUNE/SCROLL Knob Pressing the SCAN button will play the first five seconds In the List mode, the TUNE/SCROLL knob functions in of each track in the current list and then forward to the a similar manner as the scroll wheel on the iPod .
Page 246 INSTRUMENT PANEL AND CONTROLS 245 Radio Preset Buttons LIST Button In the List mode, the radio preset buttons are used as Pressing the LIST button will take to the top level menu shortcuts to the following lists on the iPod device. of the iPod .
Page 247: Video Entertainment System (Sales Code Xrv) - If Equipped
246 INSTRUMENT PANEL AND CONTROLS VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional Video Entertainment System™ (VES™) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The system is located in the headliner behind the front row seat.
Page 248: Left-Hand Switch Functions For Radio Operation
INSTRUMENT PANEL AND CONTROLS 247 • Press the switch up or down twice to listen to the Left-Hand Switch Functions for Radio Operation second track, three times to listen to the third track, • Press the top of the switch to SEEK the next listenable and so forth.
Page 249: Radio Operation And Cellular Phones
248 INSTRUMENT PANEL AND CONTROLS 5. Store the disc in its case after playing. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in 6. Do not expose the disc to direct sunlight. your vehicle can cause erratic or noisy performance from 7.
Page 250: Climate Controls
INSTRUMENT PANEL AND CONTROLS 249 CLIMATE CONTROLS Air Conditioning Operation To turn the air conditioning ON or OFF, perform Manual Control the following steps: • Position the mode control button to the desired airflow setting. • Set the front blower control to any desired speed. •...
Page 251: Front Blower Control
250 INSTRUMENT PANEL AND CONTROLS engine speed or power may be noticed when the com- Front Mode Control pressor cycles. This is a normal occurrence since the The mode control allows you to compressor will cycle on and off to maintain comfort and choose from several patterns of air improve fuel economy.
Page 252 INSTRUMENT PANEL AND CONTROLS 251 Recirculation Mode (Panel or Bi-Level) NOTE: There is a difference in temperature between the Select either the Panel or Bi-Level upper and lower outlets for added comfort. The warmer mode positions when the outside air air goes to the floor outlets.
Page 253 252 INSTRUMENT PANEL AND CONTROLS NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield. Temperature Control The temperature of the air is controlled by a slide located on the top center of the control panel.
Page 254: Rear Temperature Control - If Equipped
INSTRUMENT PANEL AND CONTROLS 253 front control will give you air from the outlets in the Rear Temperature Control — If Equipped Rotating this knob left to the headliner in the rear. Floor mode in the front will give REAR CONTROL position al- you air from the floor outlets in the rear.
Page 255: Automatic Temperature Control (Atc) - If Equipped
254 INSTRUMENT PANEL AND CONTROLS Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the Power knob. When the control is turned on, it will be in the last mode prior to being turned off. Pressing the Power knob again will turn off the control.
Page 256: Level Of Automatic Control
INSTRUMENT PANEL AND CONTROLS 255 displayed. The ATC system uses an infrared sensor hot vehicles. The system automatically adjusts the tem- located in the overhead console to measure the tem- perature, mode and fan speed to provide comfort as perature of the driver and passengers. Based on the quickly as possible.
Page 257: Manual Control (Atc)
256 INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) you press the AUTO button and no snowflake is shown. You may also choose to customize your comfort by A snowflake indicates that the A/C system is enabled. selecting the fan speed and mode manually. Turning the The snowflake will not be displayed in AUTO mode even fan speed knob or any mode button places the system though the A/C system is enabled.
Page 258 INSTRUMENT PANEL AND CONTROLS 257 Manual control of recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Outside air flows in equal proportions through the Defrost modes. The recirculation symbol will flash three floor and defroster outlets.
Page 259 258 INSTRUMENT PANEL AND CONTROLS Rear Temperature Control (ATC) NOTE: The front display will show “CONTROL IN The REAR button cycles through the following modes: REAR.” Rear Control From Front REAR OFF This allows the driver or passenger to control the rear This turns the rear system off.
Page 260: Rear Zone Climate Control - If Equipped
INSTRUMENT PANEL AND CONTROLS 259 Rear Window Defrosting and Rear Window Headliner air comes from the outlets in the headliner. Washer/Wiper Each of these outlets can be individually adjusted to Refer to “Rear Window Features” in Section 4. direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow.
Page 261: Rear Rotary Temperature Control
260 INSTRUMENT PANEL AND CONTROLS The rear compartment control uses two rotary knobs: one Rear Rotary Temperature Control for the temperature control and the other for the fan The second row seat occupants have control of the rear speed control. The mode for the rear air conditioning and temperature only when the front control unit is in the heating system is always controlled by the front control REAR CONTROL position.
Page 262: Front Unit To Rear Unit Chart
INSTRUMENT PANEL AND CONTROLS 261 Front Unit to Rear Unit Chart If the Front Control is Rear Airflow will come selected from Panel Headliner Bi-Level Headliner Floor Floor Floor Defrost Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest Rear Storage Ventilation Grilles setting, set the mode control to the panel fresh position, press the Snowflake button to turn on the air condition-...
Page 263 262 INSTRUMENT PANEL AND CONTROLS and adjust the temperature control and blower speed as Regular cleaning of the inside of the windows with a necessary to maintain comfort. For high humidity condi- non-filming cleaning solution (vinegar and water works tions, it may be necessary to remain in the Recirculation very well) will help prevent contaminants (cigarette mode to maintain comfort.
Page 264: Operating Tips Chart
INSTRUMENT PANEL AND CONTROLS 263 Operating Tips Chart...
Page 265: Rear Window Features
264 INSTRUMENT PANEL AND CONTROLS REAR WINDOW FEATURES Rear Window Wiper/Washer Automatic Climate Control Panel A rotating switch located on the climate control panel turns the rear wiper ON or OFF. Pressing the Manual Climate Control Panel rotating switch inward activates the rear window washer.
Page 266: Rear Window Defrosting
INSTRUMENT PANEL AND CONTROLS 265 If the rear wiper is operating when the ignition is turned CAUTION! OFF, the wiper will automatically return to the Park position. When the vehicle is restarted, the wiper will Use care when washing the inside of the rear window resume operation.
Page 268: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 271 Torque Converter Clutch ....279 Automatic Transmission .
Page 269 268 STARTING AND OPERATING Flowing/Rising Water ....287 Multi-Displacement System (MDS) — 5.7L Engine Only ....... . 303 Shallow Standing Water .
Page 270 STARTING AND OPERATING 269 Tread Wear Indicators ....318 Fuel Requirements ..... . 331 Life Of Tire .
Page 271 270 STARTING AND OPERATING Fuel Requirements ....340 Trailer Hitch Classification ....350 Selection Of Engine Oil For Flexible Fuel Trailer Towing Weights (Maximum Trailer Vehicles (E-85) And Gasoline Vehicles .
Page 272: Starting Procedures
STARTING AND OPERATING 271 STARTING PROCEDURES WARNING! Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may WARNING! cause serious injury or death.
Page 273 272 STARTING AND OPERATING Tip Start Feature CAUTION! Your vehicle has a “Tip Start” starting system. With “Tip Start” the driver does not need to hold the key in the To prevent damage to the starter, do not crank the START position until the vehicle starts, but can release engine for more than 15 seconds at a time.
Page 274 STARTING AND OPERATING 273 If the engine has been flooded it may start to run, but not WARNING! have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- Do not attempt to push or tow your vehicle to get it erator pedal pushed all the way to the floor.
Page 275: Engine Block Heater - If Equipped
274 STARTING AND OPERATING ENGINE BLOCK HEATER – IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine coolant and The electronic PRNDL on the instrument cluster indicates permits quicker starts in cold weather. Connect the cord the transmission gear selected. The shift lever is mounted to a standard 110-115 volt AC electrical outlet with a on the right side of the steering column.
Page 276: Gear Ranges
STARTING AND OPERATING 275 Gear Ranges WARNING! DO NOT race the engine when shifting from PARK or NEUTRAL position into another gear range. Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to “P”...
Page 277 276 STARTING AND OPERATING “N” NEUTRAL WARNING! Shift to NEUTRAL when the vehicle is standing for prolonged periods with the engine running. The engine It is dangerous to shift the gear shift lever out of may be started in this range. Set the parking brake if you PARK or NEUTRAL if the engine speed is higher must leave the vehicle.
Page 278: Overdrive Operation
STARTING AND OPERATING 277 • transmission has reached normal operating tempera- “1” 1st For driving up very steep hills and for engine braking at ture. low speeds (25 mph {40 km/h} or less) when going NOTE: If the vehicle is started in extremely cold tem- downhill.
Page 279: When To Use Tow/Haul Mode
278 STARTING AND OPERATING The transmission will downshift from OVERDRIVE to When driving in hilly areas, towing a trailer, carrying a DRIVE if the accelerator pedal is fully depressed at heavy load, etc., and frequent transmission shifting oc- vehicle speeds above approximately 35 mph (56 km/h). curs, press the TOW/HAUL button.
Page 280: Torque Converter Clutch
STARTING AND OPERATING 279 is able to shift into, and out of, Overdrive. For vehicles Torque Converter Clutch A feature designed to improve fuel economy is included with 4.7L or 5.7L engines (which have two Overdrive in all automatic transmissions. A clutch within the torque gears), the transmission may not shift into 5th gear until converter engages automatically at a calibrated speed at the transmission fluid and engine coolant are warm.
Page 281: Four-Wheel Drive Operation
280 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION Normal 4-Wheel Drive High Range - Employs inter-axle NV 140 Transfer Case Operating differential. Allows front and rear wheels to rotate at Information/Precautions – If Equipped different speeds. All road surfaces. The NV 140 is a single speed (4 HI range only) transfer case which provides convenient full-time 4-wheel drive.
Page 282 STARTING AND OPERATING 281 different speeds. This eliminates driveline binding and The transfer case NEUTRAL position is selected by component wear normally associated with driving the depressing the recessed button located on the lower left vehicle in the 4WD LOCK position on dry, hard-surfaced hand corner of the 4WD Control Switch.
Page 283 282 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine WARNING! speed is approximately three times that of the 4WD or 4WD LOCK positions at a given road speed. Take care Always engage the parking brake when powering not to overspeed the engine and do not exceed 25 mph down the vehicle if the SVC 4WD light is illumi- (40 km/h).
Page 284 STARTING AND OPERATING 283 For additional information on the appropriate use of each WARNING! transfer case mode position, refer to the following infor- mation: You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the Normal 4-Wheel Drive High range employs the inter-axle parking brake.
Page 285: Shifting Procedure - Nv 244 Generation Ii
284 STARTING AND OPERATING 4WD LOW Shifting Procedure - NV 244 Generation II The 4-Wheel Drive Low (4WD LOW) Range provides Transfer Case low speed 4-wheel drive. It locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed.
Page 286 STARTING AND OPERATING 285 wheels to complete the shift. There may be a delay up to 3. While still rolling, rotate the transfer case control 13 seconds for the shift to complete after the wheels have switch to the desired position. stopped spinning.
Page 287: Driving On Slippery Surfaces
286 STARTING AND OPERATING NOTE: If any of the requirements to select a new 1. Slow down during rainstorms or when roads are transfer case position have not been met, the transfer case slushy. will not shift. The indicator light will flash and the 2.
Page 288: Flowing/Rising Water
STARTING AND OPERATING 287 Flowing/Rising Water CAUTION! WARNING! • Always check the depth of the standing water before driving through it. Never drive through Do not drive on, or cross, a road or a path where standing water that is deeper than the bottom of water is flowing and/or rising (as in storm run-off).
Page 289 288 STARTING AND OPERATING CAUTION! WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph (8 ways inspect your vehicle’s fluids (i.e., engine oil, km/h) when driving through standing water.
Page 290: Parking Brake
STARTING AND OPERATING 289 Be sure the parking brake is firmly set when parked and PARKING BRAKE The foot operated parking brake is positioned below the the shift lever is in PARK position. When parking on a lower left corner of the instrument panel. To release the hill, you should apply the parking brake before placing parking brake, pull the parking brake release handle.
Page 291: Brake System
290 STARTING AND OPERATING BRAKE SYSTEM WARNING! In the event power assist is lost for any reason, (for example, repeated brake applications with the engine • Always fully apply the parking brake when leav- off), the brakes will still function. The effort required to ing your vehicle, or the vehicle may roll and cause brake the vehicle will be significantly increased over that damage or injury.
Page 292 STARTING AND OPERATING 291 surfaces. All vehicle wheels and tires must be the same At the instant one of the wheels is about to lock up, a size and type and tires must be properly inflated to slight pulsation can be felt in the brake pedal, indicating produce accurate signals for the computer.
Page 293 292 STARTING AND OPERATING WARNING! WARNING! • ABS cannot prevent the natural laws of physics ABS contains sophisticated electronic equipment. It may be susceptible to interference caused by improp- from acting on the vehicle, nor can it increase erly installed or high output radio transmitting braking or steering efficiency beyond that af- equipment.
Page 294: Power Steering
STARTING AND OPERATING 293 When you are in a severe braking condition involving NOTE: Increased noise levels at the end of the steering use of the ABS, you will experience some pedal drop as wheel travel are considered normal and does not indicate the vehicle comes to a stop.
Page 295: Electronic Brake Control System
294 STARTING AND OPERATING Anti-Lock Brake System (ABS) CAUTION! This system aids the driver in maintaining vehicle control Prolonged operation of the steering system at the end under adverse braking conditions. The system controls of the steering wheel travel will increase the steering hydraulic brake pressure to prevent wheel lockup and fluid temperature and should be avoided when pos- help avoid skidding on slippery surfaces during braking.
Page 296: Bas (Brake Assist System)
STARTING AND OPERATING 295 BAS (Brake Assist System) WARNING! • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction afforded.
Page 297 296 STARTING AND OPERATING The BAS is designed to optimize the vehicle’s braking WARNING! capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- • BAS cannot prevent the natural laws of physics ing the rate and amount of brake application and then from acting on the vehicle, nor can it increase applies optimum pressure to the brakes.
Page 298: Traction Control System (Tcs)
STARTING AND OPERATING 297 Traction Control System (TCS) Electronic Roll Mitigation (ERM) This system anticipates the potential for wheel lift by This system monitors the amount of wheel spin of each of monitoring the driver’s steering wheel input and the the driven wheels.
Page 299: Electronic Stability Program (Esp)
298 STARTING AND OPERATING Electronic Stability Program (ESP) WARNING! This system enhances directional control and stability of Many factors, such as vehicle loading, road condi- the vehicle under various driving conditions. ESP cor- tions and driving conditions, influence the chance rects for over/under steering of the vehicle by applying that wheel lift or rollover may occur.
Page 300 STARTING AND OPERATING 299 • Understeer - when the vehicle is turning less than WARNING! appropriate for the steering wheel position. • ESP cannot prevent the natural laws of physics ESP/TCS Indicator Light from acting on the vehicle, nor can it increase the The ESP/TCS Indicator Light starts to flash as traction afforded.
Page 301 300 STARTING AND OPERATING 4WD/4WD LOCK or 2WD Models sand or gravel conditions and more wheel spin than ESP would normally allow is required to gain traction. Trailer Sway Control (TSC) is not available when the system is in This is the normal operating mode for ESP in 4WD LOCK the Partial Off mode.
Page 302 STARTING AND OPERATING 301 NOTE: To improve the vehicle’s traction when driving vehicle speed drops below 25 mph (40 km/h) the ESP with snow chains, or starting off in deep snow, sand or system goes back to Partial Off. ESP is desensitized at low gravel, it may be desirable to switch to the “Partial Off”...
Page 303 302 STARTING AND OPERATING and the vehicle has been driven several miles at speeds WARNING! greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed In the Partial Off mode, the engine torque reduction and corrected.
Page 304: Multi-Displacement System (Mds) - 5.7L Engine
STARTING AND OPERATING 303 stop the sway. The system will reduce engine power and TIRE SAFETY INFORMATION apply individual brakes that will counter act the sway of Tire Markings the trailer. TSC will become active automatically once the swaying trailer is recognized. No driver action is re- quired.
Page 305 304 STARTING AND OPERATING • European Metric tire sizing is based on European • Temporary spare tires are high-pressure compact design standards. Tires designed to this standard have spares designed for temporary emergency use only. the tire size molded into the sidewall beginning with Tires designed to this standard have the letter “T”...
Page 306 STARTING AND OPERATING 305 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 307 306 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the speed symbol should only be achieved un- der specified operating conditions (i.e., tire pressure, vehicle loading, road conditions,...
Page 308: Tire Identification Number (Tin)
STARTING AND OPERATING 307 located on the white sidewall side of the tire. Look for the TIN Tire Identification Number (TIN) on the outboard side of black sidewall tires as mounted on the The TIN may be found on one or both sides of the tire, vehicle.
Page 309: Tire Loading And Tire Pressure
308 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-pillar. Tire And Loading Information Placard This placard tells you important information about: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry...
Page 310 STARTING AND OPERATING 309 Loading combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
Page 311 310 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 NOTE: The following table shows examples on how to kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 calculate total load, cargo/luggage, and towing capaci- kg)}.
Page 312 STARTING AND OPERATING 311...
Page 313: Tires - General Information
312 STARTING AND OPERATING 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 314: Tire Inflation Pressures
STARTING AND OPERATING 313 2. Economy— maximum loaded vehicle condition. These pressure con- Improper inflation pressures can cause uneven wear ditions will be found in the “Supplemental Tire Pressure patterns to develop across the tire tread. These abnormal Information” section of this manual. wear patterns will reduce tread life resulting in a need for earlier tire replacement.
Page 315 314 STARTING AND OPERATING check tire pressure. Do not make a visual judgement Check tire pressures more often if subject to a wide range when determining proper inflation. Radial tires may look of outdoor temperatures, as tire pressures vary with properly inflated even when they are under-inflated.
Page 316: Radial Ply Tires
STARTING AND OPERATING 315 Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 317: Compact Spare Tire - If Equipped
316 STARTING AND OPERATING Compact Spare Tire — If Equipped Do not install a wheel cover or attempt to mount a The compact spare is for temporary emergency use with conventional tire on the compact spare wheel, since the radial tires. It is engineered to be used on your style wheel is designed specifically for the compact spare.
Page 318: Tire Spinning
STARTING AND OPERATING 317 original equipped tire on the front or rear axle of your Tire Spinning vehicle, but it is not. Installation of this limited-use spare When stuck in mud, sand, snow, or ice conditions, do not tire affects vehicle handling. Since it is not the same tire, spin your vehicle’s wheels faster than 30 mph (48 km/h) replace (or repair) the original tire and reinstall on the or for longer than 30 seconds continuously without...
Page 319: Tread Wear Indicators
318 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
Page 320: Replacement Tires
STARTING AND OPERATING 319 Replacement Tires WARNING! The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for Tires and spare tire should be replaced after six years, wear and correct cold tire inflation pressure. The manu- regardless of the remaining tread.
Page 321: Alignment And Balance
320 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than Replacing original tires with tires of a different size that specified for your vehicle. Some combinations may result in false speedometer and odometer of unapproved tires and wheels may change sus- readings.
Page 322: Supplemental Tire Pressure Information - If
STARTING AND OPERATING 321 Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and To avoid damage to your vehicle, tires or chains, observe the following precautions: avoid tire cupping and spotty wear.
Page 323: Snow Tires
322 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- SNOW TIRES ing link and cable (radial) chains. Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the Tire chain use is permitted only on the rear tires of your snow tire to determine any maximum vehicle speed truck.
Page 324: Tire Rotation Recommendations
STARTING AND OPERATING 323 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns.
Page 325: Tire Pressure Monitor System (Tpms) - If Equipped
324 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold EQUIPPED The Tire Pressure Monitoring System (TPMS) will warn for any reason, including low temperature effects, or the driver of a low tire pressure based on the vehicle natural pressure loss through the tire.
Page 326 STARTING AND OPERATING 325 For example, your vehicle has a recommended cold CAUTION! (parked for more than three hours) placard pressure of 33 psi (227 kPa). If the ambient temperature is 68°F (20°C) The TPMS has been optimized for the original and the measured tire pressure is 28 psi (193 kPa), a equipment tires and wheels.
Page 327: Base System - If Equipped
326 STARTING AND OPERATING Under-inflation also reduces fuel efficiency and tire CAUTION! tread life, and may affect the vehicle’s handling and stopping ability. After inspecting or adjusting the tire pressure always • The TPMS is not a substitute for proper tire mainte- reinstall the valve stem cap.
Page 328 STARTING AND OPERATING 327 NOTE: It is particularly important for you to check the received. The vehicle may need to be driven for up to 10 tire pressure in all of your tires regularly and to maintain minutes above 15 mph (25 km/h) to receive this infor- the proper pressure.
Page 329: Premium System - If Equipped
328 STARTING AND OPERATING NOTE: Your vehicle is equipped with a non-matching 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the full size spare tire, full size spare wheel and tire assembly. the TPMS will update automatically and the TPM Telltale 1.
Page 330 STARTING AND OPERATING 329 The TPMS consists of the following components: Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, • Receiver module and inflate the low tire(s) that is flashing on the graphic •...
Page 331 330 STARTING AND OPERATING the pressure value(s) indicating which tire pressure 1. This spare tire does not have a tire pressure monitor- monitoring sensor(s) is not being received. ing sensor. Therefore, the TPMS will not monitor the tire pressure in the spare tire. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
Page 332: General Information
STARTING AND OPERATING 331 • This device must accept any interference received, display a “CHECK TPM SYSTEM” message for three seconds, and then display dashes (- - -) in place of a including interference that may cause undesired op- pressure value. eration.
Page 333: Reformulated Gasoline
332 STARTING AND OPERATING The 5.7L engine is designed to meet all Over 40 auto manufacturers worldwide have issued and emissions regulations and provide satisfac- endorsed consistent gasoline specifications (the World- tory fuel economy and performance when wide Fuel Charter, WWFC) which define fuel properties using high quality unleaded gasoline hav- necessary to deliver enhanced emissions, performance, ing an octane range of 87 to 89.
Page 334: Gasoline/Oxygenate Blends
STARTING AND OPERATING 333 NOTE: 4.7L Engine — If Equipped , is now rated for Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- E85 Ethanol use. Only vehicles with the E-85 fuel filler genates such as 10% ethanol, MTBE and ETBE. Oxygen- door label can operate on E-85.
Page 335: Materials Added To Fuel
334 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump, Fuel System Cautions therefore, you should ask your gasoline retailer whether CAUTION! or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, Follow these guidelines to maintain your vehicle’s performance: because MMT can be used at levels higher than those •...
Page 336: Carbon Monoxide Warnings
STARTING AND OPERATING 335 NOTE: Intentional tampering with emissions control Carbon Monoxide Warnings systems can result in civil penalties being assessed WARNING! against you. Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: •...
Page 337: Adding Fuel
336 STARTING AND OPERATING ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) A poorly fitting gas cap may cause the Malfunction The gas cap is behind the fuel filler door. If the gas cap is Indicator Light to turn on. lost or damaged, be sure the replacement cap is for use with this vehicle.
Page 338: Loose Fuel Filler Cap (Gas Cap) Message
STARTING AND OPERATING 337 WARNING! WARNING! • Never have any smoking materials lit in or near A fire may result if gasoline is pumped into a the vehicle when the gas cap is removed or the portable container that is inside of a vehicle. You tank filled.
Page 339: Flexible Fuel - If Equipped
338 STARTING AND OPERATING the problem is detected twice in a row, the system will manual for information on features that are common turn on the Malfunction Indicator Light (MIL). Resolving between Flexible Fuel and gasoline-only powered ve- the problem will turn the MIL light off. hicles.
Page 340: Ethanol Fuel (E-85)
STARTING AND OPERATING 339 ETHANOL FUEL (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
Page 341: Fuel Requirements
340 STARTING AND OPERATING Fuel Requirements NOTE: When the ambient temperature is above 90°F Your vehicle will operate on both unleaded gasoline with (32°C), you may experience hard starting and rough idle an octane rating of 87, or E-85 fuel, or any mixture of following startup, even if the above recommendations these two.
Page 342: Starting
STARTING AND OPERATING 341 Starting Cruising Range The characteristics of E-85 fuel make it unsuitable for use Because E-85 fuel contains less energy per gallon/Liter when ambient temperatures fall below 0°F (-18°C). In the than gasoline, you will experience an increase in fuel range of 0°F (-18°C) to 32°F (0°C), you may experience an consumption.
Page 343: Vehicle Loading
342 STARTING AND OPERATING VEHICLE LOADING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Certification Label Rating (GAWR) front and rear, and Vehicle Identification As required by National Highway Traffic Safety Admin- Number (VIN).
Page 344: Curb Weight
STARTING AND OPERATING 343 Gross Axle Weight Rating (GAWR) Inflation Pressure (Cold) The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR.
Page 345 344 STARTING AND OPERATING should then be determined separately to be sure that the WARNING! load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either Do not load your vehicle any heavier than the GVWR the front or rear axles has been exceeded but the total or the maximum front and rear GAWR.
Page 346: Trailer Towing
STARTING AND OPERATING 345 after the vehicle has been weighed both in its curb TRAILER TOWING weight condition, and in its loaded and ready for In this section you will find safety tips and information operation condition. on limits to the type of towing you can reasonably do with your vehicle.
Page 347 346 STARTING AND OPERATING Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The Gross Trailer Weight (GTW) is the weight of the The GAWR is the maximum capacity of the front and rear trailer plus the weight of all cargo, consumables and axles.
Page 348 STARTING AND OPERATING 347 • Trailer Sway Control – Mechanical Frontal Area The maximum height and maximum width of the front of The trailer sway control is a telescoping link that can be a trailer. installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with TSC (Trailer Sway Control) –...
Page 349 348 STARTING AND OPERATING used in accordance with the manufacturers’ directions, it WARNING! provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing An improperly adjusted Weight-Distributing Hitch safety. The addition of a friction/hydraulic sway control system may reduce handling, stability, and braking also dampens sway caused by traffic and crosswinds and performance, and could result in an accident.
Page 350 STARTING AND OPERATING 349 Weight-Distributing Hitch System Improper Adjustment Of Weight-Distributing System Fifth-Wheel Hitch A fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
Page 351: Trailer Hitch Classification
350 STARTING AND OPERATING Gooseneck Hitch Weight Ratings)” for the website address that contains The gooseneck hitch employs a pivoted coupling arm the necessary information for your specific drivetrain. which attaches to a ball mounted in the bed of a pickup Trailer Hitch Classification truck.
Page 352: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 351 Never exceed the maximum tongue weight stamped on Trailer Towing Weights (Maximum Trailer Weight Ratings) your bumper or trailer hitch. NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: •...
Page 353: Towing Requirements
352 STARTING AND OPERATING Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- • The tongue weight of the trailer. mended: •...
Page 354 STARTING AND OPERATING 353 • Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the Improper towing can lead to an injury accident. chains under the trailer tongue and allow enough Follow these guidelines to make your trailer towing slack for turning corners.
Page 355 354 STARTING AND OPERATING 2. GTW − Check for signs of tire wear or visible tire damage before towing a trailer. For the proper inspection 3. GAWR procedure, refer to “Tread Wear Indicators” under 4. Tongue weight rating for the trailer hitch utilized ”Tires–General Information”...
Page 356 STARTING AND OPERATING 355 − An electronically actuated trailer brake controller is WARNING! required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with Do not connect trailer brakes to your vehicle’s hy- a hydraulic surge actuated brake system, an electronic draulic brake lines.
Page 357 356 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4- and 7-pin wiring harness.
Page 358: Towing Tips
STARTING AND OPERATING 357 If using a manual transmission vehicle for trailer towing, all starts must be in 1stT gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the TOW/ HAUL feature should be selected.
Page 359 358 STARTING AND OPERATING NOTE: Check the automatic transmission fluid level Towing Tips — Cooling System before towing. To reduce potential for engine and transmission over- heating, take the following actions: Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheat- −...
Page 360: Snowplow
STARTING AND OPERATING 359 SNOWPLOW CAUTION! NOTE: Do not use this vehicle for snowplow applica- Using this vehicle for snowplow applications can tions. cause damage to the vehicle. WARNING! Snowplows, winches, and other aftermarket equip- WARNING! ment should not be added to the front end of your vehicle.
Page 361: Recreational Towing (Behind Motorhome, Etc.)
360 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND WARNING! MOTORHOME, ETC.) You or others could be injured if you leave the Recreational Towing 2WD Models vehicle unattended with the transfer case in the Recreational towing of 2WD models is not allowable. NEUTRAL position without first fully engaging the Towing the vehicle with the transmission in NEUTRAL parking brake.
Page 362 STARTING AND OPERATING 361 NOTE: The NV 244 Generation II transfer case must be 3. Turn the ignition key to the ON position without shifted into NEUTRAL for recreational towing. The NEU- starting the engine. TRAL selection button is located on the lower left-hand 4.
Page 363 362 STARTING AND OPERATING 12. Turn ignition key to the unlocked OFF position. CAUTION! 13. Shift the automatic transmission into PARK. Damage to the transmission may occur if the trans- 14. Attach vehicle to tow vehicle with tow bar. mission is shifted into PARK with the transfer case in NEUTRAL and the engine RUNNING.
Page 364 STARTING AND OPERATING 363 5. Shift the automatic transmission to NEUTRAL. NOTE: Steps 1 through 5 are requirements that must be met prior to depressing the NEUTRAL selection button, 6. Using the point of a ballpoint pen or similar object, and must continue to be met until one second elapses and depress the recessed transfer case NEUTRAL button for the shift has been completed.
Page 365: Equipment Identification Plate
364 STARTING AND OPERATING EQUIPMENT IDENTIFICATION PLATE CAUTION! The equipment Identification Plate is located on the hood inner surface. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be The following information about your vehicle is dis- damaged.
Page 366: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....366 Jump–Starting Procedures ....376 Jacking And Tire Changing .
Page 367: Hazard Warning Flasher
366 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
Page 368: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 367 If it is necessary to leave the vehicle to go for service, the JACKING AND TIRE CHANGING flasher system will continue to operate with the ignition WARNING! key removed and the vehicle locked. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
Page 369: Jack Location
368 WHAT TO DO IN EMERGENCIES Jack Location The scissor jack and tire changing tools are stowed under the second row seat. The jack is secured in place with a winged stud and a fixed stud. It is very important to secure the jack tightly in place by engaging the slot in the base to the fixed stud under the middle seat.
Page 370: Jacking Instructions
WHAT TO DO IN EMERGENCIES 369 1. Remove the rubber plug from the floor in the cargo JACKING INSTRUCTIONS area. Removing The Spare Tire The spare tire on your vehicle is located underneath the vehicle in the rear. Spare Tire Winch 2.
Page 371: Tire Changing Procedure
370 WHAT TO DO IN EMERGENCIES 3. Turn the wrench counterclockwise to lower the spare Tire Changing Procedure tire. Continue to turn the wrench until the spare tire can WARNING! be pulled out from under the vehicle. It is recommended that you stow the flat tire or spare to Getting under a jacked-up vehicle is dangerous.
Page 372 WHAT TO DO IN EMERGENCIES 371 • Block both the front and rear Preparations Park the vehicle on a firm level surface, avoiding ice or of the wheel diagonally oppo- slippery areas. Set the parking brake and place the shift site the jacking position.
Page 373 372 WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3.
Page 374 WHAT TO DO IN EMERGENCIES 373 When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as posssible with the drive tubes extending to the rear.
Page 375 374 WHAT TO DO IN EMERGENCIES correct tightness, have them checked with a torque WARNING! wrench by your authorized dealer or at a service station. Raising the vehicle higher than necessary can make WARNING! the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
Page 376 WHAT TO DO IN EMERGENCIES 375 To Stow The Flat Or Spare WARNING! Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: position it properly across the wheel opening.
Page 377: Jump-Starting Procedures
376 WHAT TO DO IN EMERGENCIES JUMP–STARTING PROCEDURES Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), WARNING! DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, •...
Page 378 WHAT TO DO IN EMERGENCIES 377 4. Connect one end of a jumper cable to the positive WARNING! terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged Do not connect the cable to the negative post of the battery.
Page 379: Freeing A Stuck Vehicle
378 WHAT TO DO IN EMERGENCIES The least amount of accelerator pedal pressure to main- WARNING! tain the rocking motion without spinning the wheels or racing the engine is most effective. Allow the engine to Any procedure other than above could result in: idle with the shift lever in NEUTRAL for at least one 1.
Page 380: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 379 WARNING! CAUTION! Chains are not recommended for freeing a stuck Tow hooks are for emergency use only, to rescue a vehicle. Chains may break, causing serious injury or vehicle stranded off-road. Do not use tow hooks for death.
Page 381: Four-Wheel Drive Vehicles
380 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles If the vehicle is to be towed more than 15 mi (25 km) or The manufacturer recommends towing with all wheels faster than 30 mph (50 km/h), it must be towed on a OFF the ground.
Page 382: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment 4.7L V-8 ....384 Engine Oil ......390 Engine Compartment 5.7L HEMI V-8 .
Page 383 382 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 398 Appearance Care And Protection From Corrosion ......414 Front Suspension Ball Joints .
Page 384 MAINTAINING YOUR VEHICLE 383 Fog Lights ......435 Engine ......437 Fluids And Capacities .
Page 385: Engine Compartment 4.7L V-8
384 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 4.7L V-8...
Page 386: Engine Compartment 5.7L Hemi V-8
MAINTAINING YOUR VEHICLE 385 ENGINE COMPARTMENT 5.7L HEMI V-8...
Page 387: Onboard Diagnostic System - Obd Ii
386 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the MIL on could cause the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 388: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 387 the odometer RESET button to turn the message off. If the Normally, the OBD system will be ready. The OBD problem persists, the message will appear the next time system may not be ready if your vehicle was recently the vehicle is started.
Page 389: Replacement Parts
388 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD system is happen: ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your a.
Page 390: Dealer Service
MAINTAINING YOUR VEHICLE 389 DEALER SERVICE WARNING! Your authorized dealer has the qualified service person- nel, special tools and equipment to perform all service You can be badly injured working on or around a operations in an expert manner. Service Manuals are motor vehicle.
Page 391: Engine Oil
390 MAINTAINING YOUR VEHICLE These items should be inspected if a malfunction is CAUTION! observed or suspected. Overfilling or underfilling the crankcase will cause Engine Oil oil aeration or loss of oil pressure. This could damage Checking Oil Level your engine. To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level.
Page 392 MAINTAINING YOUR VEHICLE 391 Change Engine Oil Engine Oil Selection Follow the Maintenance Schedule for recommended en- For best performance and maximum protection under all gine oil and filter change intervals. types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet NOTE: Under no circumstances should oil change in- the requirements of DaimlerChrysler Material Standard tervals exceed 6,000 miles (10 000 km) or 6 months,...
Page 393 392 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) Synthetic Engine Oils You may use synthetic engine oils provided the recom- SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- mended oil quality requirements are met, and the recom- ture starting and vehicle fuel economy.
Page 394: Engine Oil Filter
MAINTAINING YOUR VEHICLE 393 station, or governmental agency for advice on how and Drive Belts — Check Condition and Tension where used oil and oil filters can be safely discarded in Belt tension is controlled by means of an automatic your area.
Page 395: Spark Plugs
394 MAINTAINING YOUR VEHICLE Spark Plugs Engine Air Cleaner Filter Spark plugs must fire properly to assure proper engine Follow the Maintenance Schedule for recommended en- performance and emission control. The plugs installed in gine air cleaner filter change intervals. your vehicle should operate satisfactorily in normal service for the mileage indicated in the Maintenance WARNING!
Page 396: Engine Fuel Filter
MAINTAINING YOUR VEHICLE 395 Engine Fuel Filter CAUTION! A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Damage to the catalytic converter can result if your Should an excessive amount of dirt accumulate in the vehicle is not kept in proper operating condition.
Page 397: Maintenance Free Battery
396 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! • Do not shut off the engine or interrupt the ignition A hot exhaust system can start a fire if you park over when the transmission is in gear and the vehicle is in materials that can burn.
Page 398 MAINTAINING YOUR VEHICLE 397 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Don’t allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin or clothing.
Page 399: Power Steering - Fluid Check
398 MAINTAINING YOUR VEHICLE Power Steering — Fluid Check If necessary, add fluid to restore to the proper indicated Checking the power steering fluid level at a defined level. With a clean cloth, wipe any spilled fluid from all service interval is not required. The fluid should only be surfaces.
Page 400: Front Suspension Ball Joints
MAINTAINING YOUR VEHICLE 399 NOTE: Use only manufacturer approved A/C System WARNING! Sealers, Stop Leak Products, Seal Conditioners, Compres- sor Oils and Refrigerants. • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- Refrigerant Recovery and Recycling tioning system.
Page 401: Drive Shaft Constant Velocity Joints
400 MAINTAINING YOUR VEHICLE Drive Shaft Constant Velocity Joints attention should also be given to hood latching compo- All 4-wheel drive models are equipped with four con- nents to ensure proper function. When performing other stant velocity joints. Periodic lubrication of these joints is underhood services, the hood latch release mechanism not required.
Page 402: Windshield And Rear Window Washers
MAINTAINING YOUR VEHICLE 401 Avoid using the wiper blades to remove frost or ice from The washer fluid reservoir will hold a full gallon/liter of the windshield. Keep the blade rubber out of contact with fluid when the Low Washer Fluid Light illuminates. petroleum products such as engine oil, gasoline, etc.
Page 403: Cooling System
402 MAINTAINING YOUR VEHICLE damaged, have a competent mechanic inspect the com- Cooling System plete exhaust system and adjacent body areas for broken, WARNING! damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes You or others can be badly burned by hot coolant or to seep into the passenger compartment.
Page 404 MAINTAINING YOUR VEHICLE 403 clean by gently spraying water from a garden hose Cooling System — Drain, Flush and Refill vertically down the face of the condenser and radiator. At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection If the solution is dirty or contains a considerable amount...
Page 405 404 MAINTAINING YOUR VEHICLE Adding Coolant CAUTION! Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This • Mixing of coolants other than specified HOAT coolant can be used up to 5 Years or 100,000 miles (160 engine coolants may result in engine damage and 000 km) before replacement.
Page 406 MAINTAINING YOUR VEHICLE 405 • Use only high purity water such as distilled or deion- The cap should be inspected and cleaned if there is any ized water when mixing the water/engine coolant accumulation of foreign material on the sealing surfaces. solution.
Page 407 406 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant service attendant of this. As long as the engine operating Used ethylene glycol based engine coolant is a regulated temperature is satisfactory, the coolant bottle need only substance requiring proper disposal. Check with your be checked once a month.
Page 408: Emission Related Components
MAINTAINING YOUR VEHICLE 407 • Do not overfill the coolant recovery bottle. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Check coolant freeze point in the radiator and in the condenser clean, also.
Page 409: Brake System
408 MAINTAINING YOUR VEHICLE Ensure nylon tubing in these areas has not melted or Positive Crankcase Ventilation (PCV) Valve collapsed. Proper operation of the crankcase ventilation system requires that the PCV valve be free of sticking or plug- Inspect all hose clamps and couplings to make sure they ging because of deposits.
Page 410 MAINTAINING YOUR VEHICLE 409 Brake Master Cylinders WARNING! The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the Use of brake fluid that may have a lower initial brake system warning light is on. If necessary, add fluid boiling point, or is unidentified as to specifications to bring level to the full mark on the side of the reservoir may result in sudden brake failure during hard...
Page 411: Automatic Transmission
410 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not allow a petroleum-base fluid to contaminate Worn brake hoses can burst and cause brake failure. the brake fluid. Seal damage may result. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
Page 412 MAINTAINING YOUR VEHICLE 411 least 15 miles (24 km) of driving. At normal operating 6. Remove the dipstick again and note the fluid level on temperature the fluid cannot be held comfortably be- both sides. The fluid level should be between the “HOT” tween the fingertips.
Page 413 412 MAINTAINING YOUR VEHICLE Selection of Lubricant CAUTION! It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- Be aware that if the fluid temperature is below 50°F mance. Use only manufacturer’s recommended transmis- (10°C) it may not register on the dipstick.
Page 414: Transfer Case
MAINTAINING YOUR VEHICLE 413 CAUTION! CAUTION! Using a transmission fluid other than the manufac- Damage may result from operation of the vehicle turer’s recommended fluid may cause deterioration with low transfer case fluid. in transmission shift quality and/or torque converter shudder.
Page 415: Appearance Care And Protection From Corrosion
414 MAINTAINING YOUR VEHICLE NOTE: The presence of water in the gear lubricant will Appearance Care and Protection From Corrosion result in corrosion and possible failure of differential Protection of Body and Paint from Corrosion components. Operation of the vehicle in water, as may be Vehicle body care requirements vary according to geo- encountered in some off-highway types of service, will graphic locations and usage.
Page 416 MAINTAINING YOUR VEHICLE 415 • Avoid using abrasive compounds and power buffing The most common causes are: that may diminish the gloss or thin out the paint • Road salt, dirt and moisture accumulation. finish. • Stone and gravel impact. CAUTION! •...
Page 417 416 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 418 MAINTAINING YOUR VEHICLE 417 • For tough stains, apply Mopar Total Clean or a mild Your leather upholstery can be best preserved by regular soap solution to a clean, damp cloth and remove stain. cleaning with a damp soft cloth. Small particles of dirt Use a fresh, damp towel to remove soap residue.
Page 419 418 MAINTAINING YOUR VEHICLE Cleaning Headlights defrosters or windshields equipped with a windshield Your vehicle has plastic headlights that are lighter and wiper de-icer. Do not use scrapers or other sharp instru- less susceptible to stone breakage than glass headlights. ments which may scratch the elements.
Page 420: Fuse Block
MAINTAINING YOUR VEHICLE 419 Seat Belt Maintenance FUSE BLOCK Do not bleach, dye or clean the belts with chemical CAUTION! solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. When replacing a blown fuse, it is important to use If the belts need cleaning, use a mild soap solution or only a fuse having the correct amperage rating.
Page 421: Fuses (Interior)
420 MAINTAINING YOUR VEHICLE Fuses (Interior) The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits. It is located in the left kick panel. It is accessible through a snap-in cover. Interior Fuse Panel Cover Interior Fuse Location...
Page 422 MAINTAINING YOUR VEHICLE 421 Mini Fuse/ Ignition Run/Start Cavity Description 2 Amp Clear Color Unlock Instrument Cluster 25 Amp Natu- 15 Amp Blue Radio Battery Feed Battery Feed 10 Amp Red Spare Ignition Run/Start for Cluster/Transfer Ignition Run/Start 10 Amp Red Case/Seat Sw.
Page 423 422 MAINTAINING YOUR VEHICLE Ignition Run HVAC Cigar Lighter Igni- 20 Amp Yellow Module/Heated tion 10 Amp Red Rear Glass (EBL) 10 Amp Red Spare Fuse Relay Heating & Air Con- ABS Module Igni- 15 Amp Blue ditioning w/ATC 10 Amp Red tion Run Only Battery Feed Battery Feed...
Page 424: Fuses (Power Distribution Center)
MAINTAINING YOUR VEHICLE 423 stamped on the inside cover, otherwise the cavity num- Fuses (Power Distribution Center) ber of each fuse is stamped on the inside cover that corresponds to the following chart. These fuses and relays can be obtained from your authorized dealer. Cartridge Mini Cavity...
Page 425 424 MAINTAINING YOUR VEHICLE Cartridge Cartridge Mini Mini Cavity Fuse / Description Cavity Fuse / Description Fuse Fuse Relay Relay 40 Amp Blower Motor Relay 50 Amp JB Feed Green Feed 40 Amp JB Feed Acc Delay 10 Amp Spare Green Spare Spare...
Page 426 MAINTAINING YOUR VEHICLE 425 Cartridge Cartridge Mini Mini Cavity Fuse / Description Cavity Fuse / Description Fuse Fuse Relay Relay 20 Amp Trailer Tow Relay Electronic Automatic Yellow Transaxle (EATX) 15 Amp A/C Clutch Relay AC Clutch Blue Relay Fuel Pump Rly 15 Amp Stop Lamp Switch Spare...
Page 427: Fuses (Integrated Power Module)
426 MAINTAINING YOUR VEHICLE Fuses (Integrated Power Module) otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. Cartridge Mini Cavity Fuse / Description Fuse Relay Relay Wiper On/Off Rly Relay Wiper Hi/Lo Rly Relay Horn Rly...
Page 428 MAINTAINING YOUR VEHICLE 427 Cartridge Cartridge Mini Mini Cavity Fuse / Description Cavity Fuse / Description Fuse Fuse Relay Relay 10 Amp Rt Park Lamps 20 Amp Front Control Module Yellow (FCM) Batt #1 Relay Radiator Fan Hi Rly 20 Amp Lt Trailer-Tow Stop/ Yellow Turn...
Page 429: Vehicle Storage
428 MAINTAINING YOUR VEHICLE VEHICLE STORAGE Cartridge Mini If you are storing your vehicle for more than 21 days, we Cavity Fuse / Description Fuse recommend that you take the following steps to mini- Relay mize the drain on your vehicle’s battery: 30 Amp Ignition Off Draw Green...
Page 430: Replacement Light Bulbs
MAINTAINING YOUR VEHICLE 429 REPLACEMENT LIGHT BULBS BULB REPLACEMENT Headlights/Parking/Turn Signal LIGHT BULBS — Interior Bulb No. 1. Remove the two bolts attaching the headlight to the Dome Light ....Not Serviceable upper fender reinforcement (hood must be opened to Liftgate Lamp .
Page 431 430 MAINTAINING YOUR VEHICLE 2. Remove one nut that attaches the headlight to the 4. While firmly holding the headlight in your hands inner fender panel. Access to the nut is possible by disconnect all connectors by following the procedure opening the fender panel access door which is located in described in step number 5 below.
Page 432: Tail Lights, Turn Signals And Backup Lights
MAINTAINING YOUR VEHICLE 431 2. Rotate the light to the outboard side of the vehicle and Tail Lights, Turn Signals And Backup Lights — Replacement remove. 1. Remove the two push-pins from the tail light housing.
Page 433 432 MAINTAINING YOUR VEHICLE 3. Unlock and remove electrical connector. 4. Twist bulb sockets counterclockwise to remove from housing. 5. Remove the bulbs from the bulb sockets by pulling the bulb straight out.
Page 434: License Lights
MAINTAINING YOUR VEHICLE 433 2. Rotate the socket 1/4 turn counterclockwise. License Lights 1. Push tab towards the light and remove light assembly. 3. Pull bulb from socket.
Page 435: Center High-Mounted Stoplight
434 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight 2. Turn socket 1/4 counterclockwise and free from hous- ing. 1. Remove two screws securing stoplight housing assem- bly to the liftgate. 3. Pull bulb straight from socket to remove.
Page 436 MAINTAINING YOUR VEHICLE 435 2. Remove the far left air dam screw at the bottom of the Fog Lights fascia. 3. Peel back the liner and access the fog light. 4. Rotate the socket and connector 1/4 turn counter- clockwise and pull straight reward to disengage from the light.
Page 437 436 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric Fuel 4.7L, 87 Octane 27 gal 102 L 5.7L, 89 Octane 27 gal 102 L Engine Oil (with filter) 4.7L, SAE 5W-20, API Certified 6 qts 5.7 L 5.7L, SAE 5W-20, API Certified 7 qts 6.6 L Cooling System (includes 2.1 qts/2 L for coolant bottle...
Page 438 MAINTAINING YOUR VEHICLE 437 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology). 4.7L/5.7L Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
Page 439 438 MAINTAINING YOUR VEHICLE Chassis Component Fluids, Lubricants and Genuine Parts. Automatic Transmission Mopar ATF+4, Automatic Transmission Fluid. Transfer Case Mopar ATF+4, Automatic Transmission Fluid. Front Axle SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. Rear Axle SAE 75W-140 Synthetic Gear Lubricant or equivalent. Brake Master Cylinder Mopar DOT 3 and SAE J1703 should be used or equivalent.
Page 440 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..440 Required Maintenance Intervals ... 442 Maintenance Schedule ....440...
Page 441 440 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The “Scheduled” maintenance services, listed in bold The oil change indicator system will remind you that it is type on the following pages, must be done at the times or time to take your vehicle in for scheduled maintenance. mileages specified to assure the continued proper func- On Electronic Vehicle Information Center (EVIC) tioning of the emission control system.
Page 442 MAINTENANCE SCHEDULES 441 oil if it has been 6 months since your last oil change At Each Stop for Fuel even if the oil change indicator message is NOT • Check the engine oil level about five minutes after a illuminated.
Page 443 442 MAINTENANCE SCHEDULES • Check all lights and other electrical items for correct Required Maintenance Intervals operation. NOTE: ** Vehicles built with the 4.7L engine are At Each Oil Change equipped with 16 spark plugs; one set is located on the top of the engine under the coils and the second set is •...
Page 444 MAINTENANCE SCHEDULES 443 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter. 6,000 10 000 Rotate tires. 6,000 10 000 If using your vehicle for any of the following: Dusty or off-road conditions.
Page 445 444 MAINTENANCE SCHEDULES Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the engine air cleaner filter. 30,000 50 000 Inspect the transfer case fluid. 30,000 50 000 Replace the top row of spark plugs on 4.7L engines.
Page 446 MAINTENANCE SCHEDULES 445 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the automatic transmission fluid & filter. 120,000 200 000 Replace accessory drive belt(s). 120,000 200 000 WARNING! You can be badly injured working on or around a motor vehicle.
Page 448: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your In Mexico Contact ..... 450 Vehicle ......449 Customer Assistance For The Hearing Or Prepare For The Appointment .
Page 449 448 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....453 Traction Grades ..... . 455 Department Of Transportation Uniform Tire Temperature Grades .
Page 450: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 449 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 451: Daimlerchrysler Motors Corporation Customer Center
450 IF YOU NEED CONSUMER ASSISTANCE • Vehicle Identification Number (VIN) special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to your authorized DaimlerChrysler Motors Corporation Customer dealer’s service manager first.
Page 452: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 451 contract, call the manufacturer’s Service Contract Na- Customer Assistance for the Hearing or Speech Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 453: Warranty Information (U.s. Vehicles Only)
452 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS WARNING! MOPAR fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help Engine exhaust, some of its constituents, and certain you keep your vehicle operating at its best. vehicle components contain, or emit, chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS...
Page 454: In Canada
IF YOU NEED CONSUMER ASSISTANCE 453 To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), To order the following manuals, you may use either the or go to http://www.safercar.gov; or write to: Administra- website or the phone numbers listed below.
Page 455 454 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Call toll free at: • 1–800–890–4038 (U.S.) Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- • 1–800–387–1143 (Canada) cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 456: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 455 conditions of their use, however, and may depart signifi- DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES cantly from the norm due to variations in driving habits, The following tire grading categories were established by service practices, and differences in road characteristics the National Highway Traffic Safety Administration.
Page 457 456 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 458 INDEX...
Page 459 458 INDEX ABS (Anti-Lock Brake System) ... . 205,290 Antifreeze (Engine Coolant) ... 403,404,436 Adding Fuel ......336 Disposal .
Page 460 INDEX 459 Gear Ranges ......275 Brake Fluid ......438 Special Additives .
Page 461 460 INDEX Caps, Filler Child Restraint Tether Anchors ... . . 68,73 Fuel ....... . 336 Child Seat .
Page 462 INDEX 461 Cooling System ......402 Defroster, Rear Window ....265 Adding Coolant (Antifreeze) .
Page 463 462 INDEX Driving Emergency, In Case of Through Flowing, Rising, or Shallow Standing Freeing Vehicle When Stuck ....378 Water ......286 Jacking .
Page 464 INDEX 463 Oil ......390,436,437 Engine Oil Disposal ....392 Oil Filler Cap .
Page 465 464 INDEX Power Steering ......398 Fuel, Flexible ... . . See Flexible Fuel Vehicles Transfer Case .
Page 466 INDEX 465 Glass Cleaning ......418 Replacing ......429 Gross Axle Weight Rating .
Page 467 466 INDEX Infant Restraint ......64,65 Jacking Instructions ..... . 371 Inflation Pressure Tires .
Page 468 INDEX 467 Back-Up ......431 Low Fuel ......203,204 Brake Warning .
Page 469 468 INDEX Power Door ......30 Automatic Dimming ....84,88 Steering Wheel .
Page 470 INDEX 469 Octane Rating, Gasoline (Fuel) ....331 Overdrive OFF Switch ....277 Oil Change Indicator .
Page 471 470 INDEX USB ......217,220 Programming Transmitters (Remote Keyless Positive Crankcase Valve ....408 Entry) .
Page 472 INDEX 471 Rearview Mirrors ......84 Restraints, Occupant ..... . 41 Reclining Front Seats .
Page 473 472 INDEX Child Restraint ..... . . 64,66 Sentry Key Replacement ....15 Extender .
Page 474 INDEX 473 Snow Tires ......322 Controls ......246 Sound Systems (Radio) .
Page 475 474 INDEX Tire Markings ......303 Replacement ......319 Tire Safety Information .
Page 476 INDEX 475 Towing Assistance ..... . . 101 Automatic ......12,274 Traction .
Page 477 476 INDEX Transmitter Programming (Remote Keyless Vehicle Identification Number (VIN) ... . 7 Entry) ....... . . 25 Vehicle Information Center .
Page 478 INDEX 477 Weight Load Carrying ....342 Windshield Defroster ....251,257 Wheel Alignment and Balance .
Page 479 81-026-0850 First Edition Printed in U.S.A.

This manual is also suitable for:

Aspen 2008

Chrysler Aspen Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

Quick Links

Chapters

Related Manuals for Chrysler Aspen

Summary of Contents for Chrysler Aspen