Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 INTRODUCTION Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Warnings And Cautions
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label as a convenient record of your vehicle identification number and optional...
Page 7 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 Keys ....... 9 Obtaining Replacement Keys .
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows ......21 Power Window Operation With The Convertible Top Switch (Roadster Only) .
Page 9: Things To Know Before Starting Your Vehicle 7
A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer.
Page 10: 10 Things To Know Before Starting Your Vehicle
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Obtaining Replacement Keys Your vehicle is equipped with a theft deterrent locking system requiring a special key manufacturing process. For security reasons, replacement keys can only be ob- tained from your authorized dealer. Important! Removing the key from the steering lock activates the start lock-out.
Page 11: Glove Compartment Lock
GLOVE COMPARTMENT LOCK The glove compartment can be locked by turning the key straight up to the vertical or right position, and then removing the key. To unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 DOOR LOCKS The vehicle doors can be locked when the doors are...
Page 12: Central Locking Switch
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The doors can be unlocked by pulling on the inside door handle, pressing and releasing the top portion of the central locking switch located in the console, or by pressing and releasing the Unlock transmit button on the key fob.
Page 13: Automatic Central Locking
NOTE: The fuel filler door and center console (roadster only) cannot be locked or unlocked with the central locking switch. Automatic Central Locking The central locking switch also operates the automatic central locking feature. With the automatic central lock- ing feature activated, the doors and rear liftgate/decklid are locked at vehicle speeds of approximately 9 mph (15 km/h) or more;...
Page 14: Emergency Unlocking Feature
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Perform the quick system check which follows: Use the remote transmitter to set the alarm. If the parking lamps flash three times, the system is operating prop- erly. If not, there is a problem with a switch or the system.
Page 15: To Lock The Doors
Press the Unlock transmit button on the key fob once to unlock driver’s door, rear liftgate/decklid, fuel filler door, and center console (roadster only). Press the Unlock transmit button twice to unlock both doors, rear liftgate/ decklid, fuel filler door, and center console (roadster only).
Page 16: Panic Alarm
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Panic Alarm The panic alarm unlocks the driver’s door, turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off. The vehicle can be driven while in the Panic mode.
Page 17: Transmitter Battery Service
Transmitter Battery Service The recommended replacement Lithium battery is Pana- sonic CR 2025 or equivalent. To change the batteries: • Press release button (2) on the key fob. The key folds out. • Press the battery cover (1) in the direction of the arrow. •...
Page 18: Security Alarm System
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate/decklid, hood, and ignition for unauthorized operation.
Page 19: Decklid Internal Emergency Release - Roadster
The tow-away alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 DECKLID INTERNAL EMERGENCY RELEASE - ROADSTER As a security measure, a Decklid Internal Emergency Release lever is built into the decklid latching mecha- nism.
Page 20 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If the battery voltage drops below the minimum threshold at any time, the Trunk Internal Emergency Release will not function. WARNING! The Trunk Internal Emergency Release will not function during the convertible top operation.
Page 21: Power Windows
POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resis- tance point to open; release the switch when the window is in the desired position.
Page 22: Power Window Operation With The Convertible Top Switch (Roadster Only)
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Operation With The Convertible Top Switch (Roadster Only) The power windows can also be operated by using the convertible top switch. To operate, turn the key in the ignition switch to the ON/RUN position.
Page 23: Lap/Shoulder Belts
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In cases of other frontal impacts, roll overs, certain side impacts, rear collisions or other accidents without suffi- cient frontal or rear impact forces, the emergency tension- ing retractors will not be activated. The driver and passenger will then be protected by the fastened seat belts and inertia reel in the usual manner.
Page 25 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a little on the shoulder belt, as shown.
Page 27 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury.
Page 28: Seat Belts And Pregnant Women
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Page 29: Supplemental Restraint System (Srs) - Airbag
Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel. The passenger frontal airbag is mounted in the instrument panel, under a cover marked SRS/AIRBAG.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.
Page 31 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Occupant Restraint Controller monitors the readi- ness of the electronic parts of the system whenever the ignition switch is in the START or ON/RUN positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column.
Page 33 then quickly deflate while helping to restrain the driver and passenger. The airbag gas is vented through the airbag material towards the instrument panel. In this way the airbags do not interfere with your control of the vehicle. • The knee impact bolster helps protect the knees and working with the seat belts, position you for the best interaction with the airbags.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and passen- ger as the airbags deploy and unfold.
Page 35 • When a side impact above a predetermined threshold occurs, the sensors signal the inflator on the impacted side of the vehicle. A large quantity of nontoxic nitrogen gas is generated to inflate the airbag. The door panel opens to allow the airbag to inflate to its full size.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The operational readiness of the side airbag system is verified by the airbag indicator light in the instrument cluster when turning the key in the ignition switch to the ON/RUN position. If no fault is detected, the light will go out after approximately four seconds.
Page 37 Passenger Front Airbag On/Off Switch The on/off switch is located at the right end of the instrument panel and is accessible by opening the pas- senger door. The on/off switch is to be used only when the passenger • an infant (less than 1 year old), •...
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate. To Shut Off the Passenger Airbag: •...
Page 39 To Turn On the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The Passenger Airbag Off light on the console will turn off, or will not be illuminated when the ignition is turned to the ON position.
Page 40: Child Restraint
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready for your protection in case of a collision. While the airbag Supplemental Restraint System (SRS) is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately.
Page 41 • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs. (9 kg). “Convertible” child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint.
Page 43 • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger seat forward in the vehicle. Many, but not all LATCH-Compatible child restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attach- ment to the lower anchorage and a means of adjusting...
Page 45 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using the Vehicle Seat Belt Child restraints can be securely fastened in the passenger...
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach the tether strap to the anchor, move the seatback fully forward. Pass the child restraint tether hook over the top of the seat, through the strap near the top of the seat back, and attach it to the anchor bar behind the passenger seat, below the seatback.
Page 47: Engine Break-In Recommendations
ENGINE BREAK-IN RECOMMENDATIONS The engine in your new Crossfire does not require a long break-in period. Following these few simple guidelines is all that is necessary for a good break-in. • Drive your vehicle at moderate vehicle and engine speeds during the first 1,000 miles (1,600 km). •...
Page 48: Safety Checks You Should Make Inside The Vehicle
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).
Page 49 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....52 To Lower The Top ..... .53 To Raise The Top .
Page 50 50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats (If Equipped) ....73 To Open And Close The Hood ... . .74 Interior Lights .
Page 51 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 Using The Universal Transceiver ..101 Security ......101 Erasing Universal Transceiver Buttons .
Page 52: 52 Understanding The Features Of Your Vehicle
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. There- fore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
Page 53: To Lower The Top
CAUTION! When opening and closing the convertible top, make sure that: • There is sufficient clearance of at least 6 ft. (1.8m) for the convertible top to move up. • Nothing is placed on the tonneau cover. • The outside temperature is above 32°F (0°C). Otherwise the convertible top and other parts of the vehicle could be damaged.
Page 54 54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid possible damage to the tonneau cover and convertible top, do not allow the convertible top to remain in the suspended position. After approxi- mately 10 minutes in the suspended position, the hydraulic pressure will be released which will allow the top and the tonneau cover to lower.
Page 55 NOTE: See label attached to underside of decklid. 2. Make sure the decklid is closed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 CAUTION! Be sure to turn the ignition to the “ON/RUN” position before releasing the top from the wind- shield header.
Page 56 56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once the release handle is rotated, the windows will automatically go down. 5. Push up on the convertible top latch handle to create a gap between the header and top of approximately 8 inches (200 mm).
Page 57 NOTE: Once the top is lowered and the audible signal is heard, you can continue to push the convertible top switch down or push it within 2 seconds to raise the windows. The windows can also be closed/opened later using the power window switches.
Page 58: To Raise The Top
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise The Top: 1. Make sure the rear cargo compartment divider is still secured in the vertical position. 2. Make sure the decklid is closed. 3. Turn the ignition key to the ON/RUN position and press down on the front of the convertible top switch.
Page 59 6. Pull the latch handle and convertible top down to engage the top with the header. 7. When the top engages to the header, turn the latch handle counterclockwise just over one quarter turn to the lock position and push the latch handle up to the stored position.
Page 60 60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Once the top has been raised and locked, the cargo compartment divider can be unhooked and folded for- ward to increase the cargo compartment capacity. Follow the steps shown on the label affixed to the decklid trim. CAUTION! Once the cargo compartment divider is folded for- ward to increase the cargo compartment capacity, the...
Page 61: Convertible Top Lamp And Audible Signal Chart
Convertible Top Lamp and Audible Signal Chart Below is a table containing all of the visual and audible signals that can be seen or heard during top operation or if a fault is present. Visual and Audible Operation Mode or Fault Signals Single audible signal is Roof reaches fully open...
Page 62: Console Features
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has a power outlet/cigar lighter, an ash tray with a coin holder, a cupholder (if equipped), and the passenger airbag light. In addition, there are switches to control the heated seats (if equipped), rear spoiler, elec- tronic stability program (ESP), hazard flashers, central locking, rear defroster and towing alarm.
Page 63: Storage Compartments
Storage Compartments There is a storage compartment in the console. To open the storage compartment, lift the lid with the finger depressions on either side. To close, lower the lid until the lock engages. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 On some models, a cargo net for storage is located in the footwell area on the passenger side.
Page 64: Ashtray
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A storage pouch is located on the rear wall between the seats, and the driver’s sunvisor has a document strap. WARNING! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident.
Page 65: Coin Holder
Coin Holder With the ashtray open, folding down the cover plate reveals the coin holder, which can accommodate nine coins in various sizes up to a U.S. quarter. The coin slots are shaped to retain the coins, and the cover plate ensures that the coins remain in the coin holder.
Page 66: Glove Compartment
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Glove Compartment To lock the glove compartment, turn the key to the right and remove. To unlock, turn the key to the left and remove. Pull on the handle to open the glove compartment. CUPHOLDER (If Equipped) The cupholder is located in the console.
Page 67: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle) The mirror should be adjusted with the glare control set in the day position (toward windshield).
Page 68: Power Remote Control Outside Mirrors
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror.
Page 69: Vanity Mirrors
Vanity Mirrors A vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and slide open the mirror cover. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 SEATS Your vehicle’s seats can be adjusted either manually or electrically, depending on how your vehicle is equipped.
Page 70: Manual Seat Adjustments (If Equipped)
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When moving the seat, be sure that there are no items in the footwell or behind the seats. Otherwise you could damage the seats. Manual Seat Adjustments (If Equipped) Seat Height (Drivers Seat Only) •...
Page 71 Forward/Rearward • Pull up on handle 4. • Move the seat forward or backward to your desired position which allows you to reach the pedals com- fortably. • Let go of handle 4. The seat should make an audible click when positioned properly. •...
Page 72: Driver Eight-Way Power Seat (If Equipped)
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Eight-Way Power Seat (If Equipped) The switches to adjust the power seats are located on the outboard side of each seat. The driver’s seat features eight-way power adjustment - horizontal, vertical, cush- ion tilt and back angle.
Page 73: Passenger Four-Way Power Seat (If Equipped)
Passenger Four-Way Power Seat (If Equipped) The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle. Heated Seats (If Equipped) This feature heats the driver and passenger seats. The controls for the heated seats are located on the instrument panel, below the radio.
Page 74: To Open And Close The Hood
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever located inside your vehicle, below the instrument panel. Then, reach under the hood and pull upward on the safety latch and lift the hood. To prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm).
Page 75: Interior Lights
INTERIOR LIGHTS A two-position mode selector switch controls the interior lights located in the overhead console. The AUTO mode turns the lights on when a door is open or ajar, or when locking or unlocking the vehicle. AUTO mode also has a “fade to off” feature. When the doors are closed or locked, they gradually “fade”...
Page 76: Instrument Panel Lighting
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Lighting With the parking lights or headlights on, rotate the dimmer control to the left of the speedometer to increase or decrease brightness of the instrument panel. Night Security Illumination For added security when exiting the vehicle after driving with the exterior lights on, the lights will switch on again for approximately 30 seconds after closing the last door.
Page 77: Daytime Running Lights (Where Applicable)
Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver’s door is opened. Daytime Running Lights (Where Applicable) VEHICLES WITH AUTOMATIC TRANSMISSION The low beam headlights, parking lights, side marker lights, taillights and license plate lights are automatically switched on whenever the vehicle is started and the transmission gear selector is in a driving position.
Page 78: Multifunction Control Lever
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Standing lamps are intended for short term use when parking. If these lights are left on for a long period of time, your car’s battery may drain, causing a possible starting problem. Assure that the head- lamp switch is in the OFF position when leaving the vehicle.
Page 79: Headlight Dimmer Switch
To operate the turn signals continuously, move the con- trol lever up or down past the point of resistance. The operation is automatically canceled when the steering wheel is turned to a large enough degree. If one of the turn signal lights fail, the turn signal indicator system flashes and sounds at a faster than normal rate.
Page 80: Passing Light
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the control lever is released.
Page 81: Mist Function
Push the end of the lever inward and hold it to activate the wiper and washer together. Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WARNING! Sudden loss of visibility through the windshield...
Page 82: Telescoping Steering Column
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located in the instrument cluster will come on. To lengthen or shorten the steering column, pull out or push in the steering wheel.
Page 83: Tire Pressure Monitor System
NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not locked properly. Do not drive the vehicle until you have properly locked the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 TIRE PRESSURE MONITOR SYSTEM Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 The TPM system will cause the indicator lamp in the instrument cluster to illuminate whenever the pressure in one tire falls 25% below the recommended pressure shown on the vehicle’s tire label. NOTE: The pressure in your tires changes with tem- perature.
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and/or style.
Page 87: Rear Spoiler
REAR SPOILER CAUTION! Do not push or pull on the spoiler when deployed. Damage to the spoiler could result. A rear spoiler enhances vehicle stability. The rear spoiler deploys automatically when vehicle speed reaches ap- proximately 62 mph (100 km/h). The spoiler begins to retract at 39 mph (62 km/h).
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The spoiler control also incorporates an emergency stop feature. If, for any reason, spoiler motion needs to be stopped, pressing either the top or bottom of the switch will stop the spoiler motion. Once the deployment speed is reached, however, the spoiler deploys to its full up position.
Page 89: Brake Assist System (Bas)
WARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illumi- nated. You could have reduced vehicle stability and control. WARNING! Keep hands and fingers away from the spoiler and spoiler linkage when the spoiler is deploying or retracting.
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BAS is designed to maximize the vehicle’s braking capability during emergency braking maneuvers. The system applies maximum power boost to the brakes more quickly in emergency braking conditions than might otherwise be afforded solely by the driver’s brak- ing style.
Page 91: Electronic Stability Program (Esp)
If the malfunction indicator light stays illuminated, have the BAS and ESP checked at your authorized dealer as soon as possible. ELECTRONIC STABILITY PROGRAM (ESP) WARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch. With the ESP system switched off, the engine torque reduction feature is cancelled.
Page 93: Synchronizing Esp
CAUTION! If the vehicle is towed with the front axle raised, the engine must be shut off (key in the ignition switch to the OFF/LOCK or ACC position). Otherwise the ESP will immediately be engaged and will apply the rear wheel brakes.
Page 94: Electronic Speed Control
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operat- ing the lever.
Page 95: To Vary The Speed Setting
To accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. To decelerate and set a speed, press the lever down. Press down and hold the lever to decelerate, or press down and release to set a speed.
Page 96: To Deactivate
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory. Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn off the speed control and erase the memory.
Page 97: Using Speed Control On Hills
Using Speed Control On Hills Your vehicle is equipped with interactive speed control. This feature activates when driving up or down hills with the speed control engaged and the driver’s foot off the accelerator. WARNING! Speed control can be dangerous where the system can’t maintain a constant speed.
Page 98: Programming The Universal Transceiver
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 99 NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the three buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view.
Page 100: Gate Operator/Canadian Programming
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener).
Page 101 5. Continue to press and hold the universal transceiver button while you press and release every two seconds (“cycle”) your hand-held transmitter until the frequency signal has successfully been accepted by the universal transmitter. (The indicator light will flash slowly and then rapidly.) Proceed with Programming Step 6 to complete.
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation.
Page 103: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....104 Instrument Cluster ..... 105 Instrument Cluster Description .
Page 104: Instruments And Controls
104 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 105: Instrument Cluster
INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the UNDERSTANDING YOUR INSTRUMENT PANEL 105 cluster, or turning the key in the ignition switch to the ON/RUN position.
Page 106 106 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 107: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Low Windshield Washer System Fluid Level Warning Light With the key in the ignition switch turned to the ON/RUN position, the indicator light comes on. It should go out when the engine is running. If the indicator light does not go out after starting the engine, or if it comes on while driving, the fluid reservoir is less than ⁄...
Page 108 108 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS is designed to monitor your tire pressure and will not function as a tire pressure gauge. After adjusting the air pressure in a tire, there will be a delay before the system updated the display NOTE: The TPMS can inform you about a low tire pressure condition, but it does not replace normal tire maintenance.
Page 109 CAUTION! Continuing to drive with an overheated engine cool- ing system can cause damage to the engine or other components. 5. Fuel Gauge When the ignition is in the ON/RUN position, the pointer will show the level of fuel remaining in the tank. The arrow to the right of the gas pump symbol shows which side of the vehicle the fuel filler door is located on.
Page 110: Understanding Your Instrument Panel 103
110 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Brake System Warning Light The dual brake system provides a reserve braking capability if a failure occurs in a portion of the hydraulic system. This light monitors both the brake fluid level and the parking brake.
Page 111 The indicator light will come on when the exterior light fails. If a brake light fails, the light outage indicator will come on when applying the brake and stays on until the engine is turned off. NOTE: If additional lighting equipment is installed (e.g., auxiliary headlights, etc.) be certain to connect into the fuse before the failure indicator monitoring unit in order to avoid damaging the system.
Page 112 112 UNDERSTANDING YOUR INSTRUMENT PANEL The seat belt indicator light will remain lit until the seat belts are fastened. 15. Charging System Indicator Light Should the charging system indicator light fail to come on prior to starting when the key is in the ignition switch in the ON/RUN position, or should it fail to go out after starting or during operation, it indicates a malfunction...
Page 113 The display can be adjusted with the knob/button lo- cated to the left of the clock. 18. Gear Indicator For automatic transmission vehicles, the current gear shift selector range is indicated in the gear range indica- tor display. 19. Push Button for Time Setting To adjust the time display, turn the key in the ignition switch to the ON/RUN or ACC position.
Page 114 114 UNDERSTANDING YOUR INSTRUMENT PANEL To reset the trip odometer, press the knob/button once with the key in the ON/RUN position. Press the knob/ button twice with the key removed or in the OFF/LOCK or ACC position. The FSS permits a flexible service schedule that is directly related to the operating conditions of the vehicle.
Page 115 or while driving when reaching the service warning threshold. It can be canceled manually by pressing the knob/button. Once the suggested term has passed, the message plus either the symbol for Service A or the symbol for Service B preceded by a – (minus symbol) blinks for approximately 30 seconds and a signal sounds every time when turning the key to the ON/RUN position.
Page 116 116 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! The outside temperature indicator is not designed to serve as an ice-warning device and is unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. 24.
Page 117 WARNING! Do not drive the vehicle until you have properly locked the steering column. 26. Check Engine Light This light is part of an onboard diagnostic system that monitors the emissions and en- gine control systems. If a problem is detected in one of these systems, the Check Engine light will come on.
Page 118 118 UNDERSTANDING YOUR INSTRUMENT PANEL CHECKING ENGINE OIL LEVEL A sensor in the oil pan allows oil level to be checked without opening the hood. It provides an accurate mea- surement of oil level, whereas the low engine oil level indicator warns that oil level is definitely too low.
Page 119: Infinity Modulus" Am/Fm Stereo Radio With Single-Disc Cd Player And Gps Navigation
“INFINITY MODULUS” AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER AND GPS NAVIGATION (OPTIONAL - See separate User’s Manual) AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER INFINITY MODULUS Entertainment Systems A premium Infinity Modulus AM/FM stereo, single-disc CD audio system is standard equipment on some mod- els.
Page 120 120 UNDERSTANDING YOUR INSTRUMENT PANEL The volume is controlled by rotating the ON/OFF knob to the left or right. Audio (AUD) Settings • Bass (BASS) Press the AUD button repeatedly until BASS appears. Rotate the right rotary control for the desired level (from -9 to +9).
Page 121 FM AS – An autostore feature will store the 9 current stations with the strongest signal on station buttons 1-9 in the order of their signal quality. Press the FM button repeatedly until FM AS is displayed to perform an autostore scan. Press the multifunction button labeled AS repeatedly until AS-SEEK is displayed.
Page 122 122 UNDERSTANDING YOUR INSTRUMENT PANEL Press the button again to keep the received program. If the selected station does not transmit a PTY identifica- tion, the display will show NO PTY. If all criteria for evaluating RDS are not met, the unit will only display the frequency.
Page 123: Cd Player Operation
AM-AM AS The system has two AM modes available. Press the AM button repeatedly until the band or operation mode is selected. To search in this mode, press the right rotary control/push button and the abbreviation SC is dis- played. Receivable stations can be heard for eight sec- onds.
Page 124 124 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Before inserting a CD, assure that a CD is not already in the player. Press the CD button; if the display shows NO CDS, a new CD can be inserted. If a CD is already loaded, press and release the EJT button and allow time for the current CD to be ejected.
Page 125: User Menu
• Relative Time Display (T) Press the multifunction button T for the time of the currently playing track to be displayed for approxi- mately eight seconds. • Random Play (RP) Press the multifunction button RP for random genera- tion of the next track to be played. Press the button again to cancel the feature.
Page 126: Mono/Stereo
126 UNDERSTANDING YOUR INSTRUMENT PANEL Mono/Stereo In order to suppress reception-related interference, three different parameters can be set to optimize reception. To activate, call up the user menu, then press the right rotary control/push button repeatedly until STEREO, STO AUTO or MONO is displayed (depending on the currently selected setting, you may need to turn the knob also for your selection).
Page 127: Compact Disc Maintenance
Call up the user menu, then press the right rotary control/push button repeatedly until AUDIO PH or PH MUTE is displayed (depending on the currently selected setting, you may need to turn the knob also for your selection). COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1.
Page 128: Radio Operation And Cellular Phones
128 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 129: Temperature Control
The settings and controls are as follows: Temperature Control Use the driver or passenger temperature control to regulate the temperature of the air inside the passenger compartment. The blue area of the control indicates cooler temperatures, while the red area indicates warmer temperatures.
Page 130: Basic Setting - Air Conditioner
130 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Setting - Air Conditioner Press the air conditioning ON/OFF switch. The light in the switch will illuminate. Select a temperature for each side of the passenger compartment. Select the air volume with the fan control switch, at least to position 1. Set the air distribution control switch to one of the positions shown above.
Page 131 control switch to position 1 or higher. Close the center, left, and right side air outlets. Turn the defroster outlets for the side windows to the detent position. NOTE: The air conditioner removes moisture from the air inside your vehicle. The quickest and most efficient method for defogging your windows, even if the air temperature in your vehicle is cool, is to use the air conditioner.
Page 132 132 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control - OFF To switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up.
Page 133: Dust Filter (If Equipped)
after approximately 30 minutes, at outside temperatures above approximately 40°F (5°C); after approximately five minutes, if the A/C button is pressed. At high outside temperatures, the system automatically engages the recirculated air mode for approximately 30 minutes, thereby increasing the cooling capacity perfor- mance.
Page 134: Operating Tips
134 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 135: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....137 Normal Starting ..... . 137 Extremely Cold Weather (Below -20°F Or -29°C) .
Page 136 136 STARTING AND OPERATING Electronic Stability Program (ESP) ..152 Synchronizing ESP ....153 ESP Control Switch .
Page 137: Starting Procedures
STARTING PROCEDURES WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sure that the parking brake is engaged and that selector lever is in the NEUTRAL or PARK position (gearshift lever in Neutral).
Page 138: Extremely Cold Weather (Below -20°F Or -29°C)
138 STARTING AND OPERATING NOTE: Due to the starter non-repeat feature, the key must be turned completely to the left before attempting to start the engine again. Extremely Cold Weather (below -20°F or -29°C) For reliable starting in areas where temperatures fre- quently drop below -20°F (-29°C), we recommend the use of an externally powered battery and an electric engine block heater.
Page 139: After Starting
If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
Page 140: Recommended Shift Speeds
140 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Be sure the transmission is in FIRST gear, (not THIRD), when starting from a stopped position. Damage to the clutch can result from starting in THIRD.
Page 141: Automatic Transmission
WARNING! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever, which could result in an accident or serious injury.
Page 142: Stopping
142 STARTING AND OPERATING • Program mode selector switch • Accelerator position • Vehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position.
Page 143: Maneuvering
Maneuvering To maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration.
Page 144: Reverse
144 STARTING AND OPERATING With a malfunction in the vehicle’s electrical system, the selector lever could remain locked in the PARK position. To unlock the selector lever manually, insert the end of the multipurpose tool from the glove box (or ball point pen) into the covered opening below the position “D”...
Page 145: Drive
Drive The transmission automatically upshifts through fifth gear. The DRIVE position provides optimum driving characteristics under all normal operating conditions. AutoStick Gear selection The transmission gear can be selected by pressing the selector lever to the right or the left with the selector lever in the DRIVE position.
Page 146: Gear Ranges
146 STARTING AND OPERATING The delayed upshift is effective with vehicle speeds below 31 mph (50 km/h) at partial throttle and engine temperatures below 95°F (35°C). To prevent the engine from laboring at low RPM when driving uphill or with your vehicle heavily loaded, the automatic transmis- sion will downshift when necessary to maintain en- gine RPM within the best torque range.
Page 147: Program Mode Selector Switch
Program mode selector switch The transmission is provided with a selector switch for Standard “S” and Winter/Wet “W” (snow and ice) pro- gram modes. For standard mode, press the “S” symbol on the switch. Use this mode for all regular driving. The vehicle starts out in FIRST gear.
Page 148: Emergency Operation (Limp Home Mode)
148 STARTING AND OPERATING Emergency Operation (Limp Home Mode) If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in Limp Home Mode which engages when there is a malfunction of the transmission. This condition may be accompanied by the CHECK ENGINE light in the instrument cluster coming on.
Page 149 To release the parking brake, slightly pull up the handle while pushing the lock button, and guide the lever downward to its stop. The brake warning light in the instrument cluster should go out. A warning sounds if you start to drive without having released the parking brake.
Page 150: Brake System
150 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 151 Once the brake pedal is released, the BAS is deactivated. The malfunction indicator light for the BAS is combined with the Electronic Stability Program (ESP) malfunction indicator light. STARTING AND OPERATING 151 The BAS/ESP malfunction indicator light in the instru- ment cluster comes on with the key in the ignition switch turned to the ON/RUN position and should go out with the engine running.
Page 152: Electronic Stability Program (Esp)
152 STARTING AND OPERATING Electronic Stability Program (ESP) The ESP enhances directional control and reduces wheel- spin under various driving conditions. When ESP is active, engine torque is limited and the ESP warning light starts to flash. In winter operation, the effectiveness of the ESP can be enhanced by equipping the vehicle with DaimlerChrysler recommended mud and snow (M+S) rated radial-ply tires and/or snow chains.
Page 153: Synchronizing Esp
CAUTION! If the vehicle is towed with the front axle raised (see the What To Do In Emergencies section in this manual), the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes.
Page 154: Esp Control Switch
154 STARTING AND OPERATING ESP Control switch The ESP control switch is located in the center console. When the ESP is switched off, the warning light in the instrument cluster comes on. When the ESP is switched on, the warning light goes out. To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, switch off the ESP by pressing the upper half of the ESP...
Page 155: Anti-Lock Brake System (Abs)
Anti-Lock Brake System (ABS) The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. The system operates to prevent wheel lock-up and help avoid skidding on slippery surfaces.
Page 156 156 STARTING AND OPERATING apparent on ice and snow. The anti-lock brake system pump motor makes a low humming noise during opera- tion, which is normal. WARNING! Pumping of the brake pedal will diminish the effec- tiveness of the anti-lock brakes and may lead to an accident.
Page 157 below 10 volts, the malfunction indicator light comes on and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
Page 158: Brake Pad Break-In
158 STARTING AND OPERATING Brake Pad Break-In The brakes on your vehicle do not require a long break-in period, but avoid repeated hard brake applications from high speeds during initial break-in. Also avoid severe brake loading such as may be encountered when de- scending long mountain grades.
Page 159: Tire Safety Information
TIRE SAFETY INFORMATION See general tire safety information included in the “If You Need Consumer Assistance” section of this manual. TIRES—GENERAL INFORMATION Please take time to read the tire warranty booklet in your Owner’s Manual package. It contains valuable informa- tion on tire maintenance.
Page 160: Tire Inflation Pressures
160 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 161 CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 162: Radial-Ply Tires
162 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 163: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 164 164 STARTING AND OPERATING Recommended Tire Inflation Pressures Sport Performance (Y speed rating) tires and All-Season Performance (W speed rating) tires Front 225/40 ZR18 ....32 psi (221 kPa) Rear 255/35 ZR19.
Page 165: Alignment And Balance
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Check with your authorized dealer before replacing tires with a different size. Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage Poor suspension alignment may result in:...
Page 166 166 STARTING AND OPERATING cannot be expected to function as a tire pressure gauge. There can be a delay between the instant you adjust the air pressure in a tire and when the system updates the display. The TPMS is not intended to provide you with notification of rapid air loss.
Page 167: General Information
TIRE CHAINS The RUD-matic DISC is the only tire chain system approved for use on the Chrysler Crossfire. Chains should only be used on the rear wheels and only with the recommended winter mud and snow (M+S) tires and wheels. Follow the manufacturer’s mounting instructions.
Page 168: Original Equipment Tires
168 STARTING AND OPERATING ORIGINAL EQUIPMENT TIRES Your vehicle is equipped with either sport performance tires or all-season performance tires. The sport perfor- mance tires offer the maximum road handling capability in dry and wet weather conditions. The all-season per- formance tires, while offering slightly less road handling capability, are able to provide traction capability in snow and ice conditions.
Page 169: Tire Rotation Recommendations
If you need snow tires, the recommended size for the front and rear tires is the same size as the original equipment front tires. This size tire on the rear allows the use of tire chains on the rear wheels. Selection of this size tire also requires the purchase of two additional wheels with the same size specification as the original equip- ment front wheels.
Page 170 170 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 171: Fuel Requirements
If you experience these problems, try another brand of gasoline before consider- ing service for the vehicle. Over 60 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties...
Page 172: Mmt In Gasoline
172 STARTING AND OPERATING CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system com- ponents. Problems that result from using methanol/gasoline blends are not the responsibility of DaimlerChrysler Corporation and may not be covered by the Limited Warranty.
Page 173: Adding Fuel
states adopting California emission standards, your ve- hicle will operate satisfactorily on fuels meeting Federal specifications, but emission control system performance may be adversely affected. Gasoline sold outside of California is permitted to have higher sulfur levels, which may affect the performance of the vehicle’s catalytic converter.
Page 174 174 STARTING AND OPERATING NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container, the container should have a flexible nozzle long enough to force open the restricting door.
Page 175: Vehicle Loading
VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressure label attached to the driver door pillar. Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Cargo Capacity (with two persons) .
Page 176: Trailer Towing
176 STARTING AND OPERATING CAUTION! • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof luggage rack which may come in contact with the roof panel. The load should be secured and placed on top of the rack, not directly on the roof.
Page 177 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....178 If Your Engine Overheats ....178 TIREFIT Tire Repair And Jacking .
Page 178: 178 What To Do In Emergencies
178 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. Do not use this emergency warning system when the vehicle is in motion.
Page 179 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
Page 180: Tirefit Tire Repair And Jacking
180 WHAT TO DO IN EMERGENCIES TIREFIT TIRE REPAIR AND JACKING TIREFIT Small punctures, particularly those in the tread, can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C).
Page 181 WARNING! Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances. Do not drive the vehicle under such circumstances.
Page 182 182 WHAT TO DO IN EMERGENCIES 11. Turn the ignition key to the ON/RUN position. 12. Press the switch on the air pump to 1. The air pump should start to inflate the tire. 13. After five minutes, the tire should be inflated to at least 26 psi (180 kPa) on the pressure gauge.
Page 183: Preparations For Jacking
Preparations for Jacking WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 184: Jack Location And Instructions
184 WHAT TO DO IN EMERGENCIES • Block the wheel diagonally opposite the flat tire. • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle.
Page 185 WHAT TO DO IN EMERGENCIES 185 2. The lifting points for the jack are located beneath the outer edge of the body side, directly behind the front wheel housings, and in front of the rear wheel housings.
Page 186 186 WHAT TO DO IN EMERGENCIES NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the ground.
Page 187: Jump-Starting The Battery
WARNING! A loose jack or tool thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and tools in the places provided. JUMP-STARTING THE BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised.
Page 188 188 WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immedi- ately with large quantities of water.
Page 189: Driving On Slippery Surfaces
3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive jump-start attachment of the booster battery. Connect the other end of the same cable to the positive jump-start attachment of the discharged battery.
Page 190: Traction
190 WHAT TO DO IN EMERGENCIES Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1.
Page 191: Towing A Disabled Vehicle
TOWING A DISABLED VEHICLE We recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. CAUTION! Important! If towing the vehicle, please note the following: With the automatic central locking acti- vated and the key in the ignition switch turned to the ON/RUN position, the vehicle doors lock if the left front wheel and the right rear wheel are turning at...
Page 192: Towing Eyes
192 WHAT TO DO IN EMERGENCIES CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck.
Page 193 WHAT TO DO IN EMERGENCIES 193 Insert the tool (or similar sized screwdriver) into the slot in the grille as shown (the tool must be inserted far enough to engage the clip on the left side of the grille). Push the tool to the left to disengage the clip and detach the grille.
Page 194: Tow-Away Alarm
194 WHAT TO DO IN EMERGENCIES Tow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights.
Page 195: Convertible Top Emergency Operation
CONVERTIBLE TOP EMERGENCY OPERATION If the convertible top cannot be closed using the convert- ible top switch, check the following: • Is the decklid closed properly? • Is there sufficient battery voltage? Start the engine if necessary. • Is the rear cargo compartment divider secured in the vertical position? If the power convertible top operation does not function properly, you can close the convertible top manually.
Page 196: Relieving Hydraulic Pressure
196 WHAT TO DO IN EMERGENCIES Relieving Hydraulic Pressure NOTE: The hydraulic pressure must be relieved before the top can manually be raised or lowered. 1. Turn the ignition to the “ON” position. 2. Push down on the convertible top switch and hold in that position.
Page 197 3. Unlock the storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 4. Open the tonneau cover and secure it in the upright position.
Page 198 198 WHAT TO DO IN EMERGENCIES 6. Move the convertible top toward the windshield header. WARNING! Do not place your hands in the convertible top frame areas. Serious personal injury may occur. 7. Do not place the convertible top frame onto wind- shield header.
Page 199 10. Lock the convertible top storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. WHAT TO DO IN EMERGENCIES 199 11.
Page 200 200 WHAT TO DO IN EMERGENCIES 12. Fold down the locking latch handle. 13. Turn the latch handle just past one quarter turn clockwise and pull the convertible top frame carefully down until it meets the windshield header attachment points. 14.
Page 201: Opening A Locked Decklid
WHAT TO DO IN EMERGENCIES 201 Opening a Locked Decklid It is possible for the decklid to become locked if a convertible top system malfunction occurs. If the top is manually moved to the full up or full down position when the hydraulic pressure is relieved, the decklid should unlock.
Page 203 MAINTAINING YOUR VEHICLE CONTENTS 3.2L Engine ......205 Onboard Diagnostic System (OBD II) ..206 Emissions Inspection And Maintenance Programs .
Page 204 204 MAINTAINING YOUR VEHICLE Manual Transmission ....229 Appearance Care And Protection From Corrosion ......230 Convertible Top Care .
Page 205: Maintaining Your Vehicle 205
MAINTAINING YOUR VEHICLE 205 3.2L ENGINE...
Page 206: Onboard Diagnostic System (Obd Ii)
206 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your Crossfire is equipped with a sophisti- cated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
Page 207: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the CHECK ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing.
Page 208: Replacement Parts
208 MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 209: Maintenance Procedures
WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician.
Page 210 210 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 211 Change Engine Oil The oil change interval for your Crossfire is initially set at 7,000 miles (Canada: 11,000 km). The Flexible Service System (FSS) in your vehicle evalu- ates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service.
Page 212 212 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40. The FSS may not alert for an oil change at the proper interval if an unapproved engine oil is used;...
Page 213: Maintenance Schedules
Drive Belts - Check Condition and Tension At the distance shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure.
Page 214 214 MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage.
Page 215: Ignition Wiring System
• Do not idle the engine with any spark plug wires disconnected for a prolonged period. Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits.
Page 216: Air Conditioner
216 MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Page 217: Power Steering Fluid
Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S. Steering noise and reduced component life may result if an unapproved fluid is used. During scheduled maintenance, check the power steering fluid level at the power steering fluid reservoir.
Page 218: Chassis Lubrication
218 MAINTAINING YOUR VEHICLE Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints when- ever under-vehicle service is done. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication.
Page 219: Windshield Wiper Blades
Insert the key into the lock cylinder and rotate from the unlocked to the locked position without adding more lubricant. Repeat this procedure three or four times. Wipe all the lubricant off the key with a clean cloth, to avoid soiling clothing.
Page 220: Windshield Washer Reservoir
220 MAINTAINING YOUR VEHICLE Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C).
Page 221: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent technician inspect the complete ex- haust system and adjacent body areas for broken, dam-...
Page 222: Cooling System
222 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition key is in the ON position.
Page 223 If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal.
Page 224 224 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing, according to the temperatures occurring in the area where the vehicle is operated. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank.
Page 225: Hoses And Vacuum/Vapor Harnesses
• If frequent coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain a coolant concentration of a minimum of 50% ethylene glycol Extended Life Coolant and high qual- ity water with recommended antifreeze for proper corrosion protection of your engine cooling system...
Page 226 226 MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.
Page 227 Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap.
Page 228: Automatic Transmission
228 MAINTAINING YOUR VEHICLE CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid as seal damage will result! Automatic Transmission The fluid in the automatic transmission should be changed at 80,000 miles (129,000 km), along with the transmission fluid filter. After that, the transmission fluid is filled for life.
Page 229: Manual Transmission
NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. Manual Transmission Selection of Lubricant No fluid service is required. Use only fluid approved to MB 236.2. SAE 5W-20 engine oil, meeting API SL or GF-3, may be substituted. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for the correct fluid type.
Page 230: Appearance Care And Protection From Corrosion
230 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body protection requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 231 CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
Page 232 232 MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemi- cals and equipment to prevent damage to the wheels. Only Mopar Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim.
Page 233 ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. CAUTION! The use of vinyl, leather or plastic protectants may cause excessive gloss and/or discoloration of interior trim parts. WARNING! Do not use volatile solvents for cleaning purposes.
Page 234: Convertible Top Care
234 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 235: Washing
Washing CAUTION! • Remove bird droppings immediately. The organic acid can damage the material and cause the top to leak. • Never use a power washer to clean the top, as you may damage the top material. • If an automatic car wash is used, never use hot- wax.
Page 236: Weather Strip Care
236 MAINTAINING YOUR VEHICLE The following methods are sufficient if the top is only lightly soiled: Dry Cleaning Brush the dry top with a soft-bristled brush from front to rear of the vehicle. Wet Cleaning Wash with clear water or with a mild detergent and an ample supply of luke warm water by wiping with a soft-bristled brush or sponge from front to rear.
Page 237: Fuses
MAINTAINING YOUR VEHICLE 237 FUSES Underhood Accessory Fuse Block Fuses The underhood accessory fuse block fuses are located under the hood on the driver’s side, between the brake master cylinder and the left front fender. To remove the lid, squeeze the tabs together located at the front of the fusebox.
Page 238 238 MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
Page 239 Underhood Accessory Fuse Block Fuses Cavity Fuse Circuits 5 Amp Garage Door Opening Signal, Beige TPM and Seat Heater 5 Amp Occupant Restraint Controller Beige Passenger Airbag Off 5 Amp Indicator, Safety Restraint System Beige and Indicator, Passenger Airbag 7.5 Amp Heated Mirror Brown 15 Amp...
Page 240 240 MAINTAINING YOUR VEHICLE Cavity Fuse Circuits 40 Amp Electronic Stability Program Orange 40 Amp Power Window, Front Orange 30 Amp Wiper Motor Green 30 Amp Seat Adjustment Right Side Green 30 Amp Seat Adjustment Left Side Green 15 Amp Sound Booster (Amplifier) Blue 30 Amp...
Page 241: Relay Control Module Fuses
Relay Control Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compart- ment. Slide the control module box cover retaining clips forward and lift the cover from the control module box to gain access to the relay control module fuses.
Page 242: Interior Fuses
242 MAINTAINING YOUR VEHICLE Interior Fuses The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door. Interior Fuses Cavity Fuse...
Page 243: Replacement Bulbs
Cavity Fuse Circuits 15 Amp Right Low Beam Blue 7.5 Amp Right Parking/Tail Light Side Brown Marker 15 Amp Left Low Beam Blue 15 Amp Fog Light Blue 7.5 Amp Left Parking/Tail Light Side Brown Marker 7.5 Amp License Plate/Instrument Cluster Brown Lighting/Symbol Lighting Not Used - Spare Fuse...
Page 244: Exterior Light Bulb Service
244 MAINTAINING YOUR VEHICLE EXTERIOR LIGHT BULB SERVICE Headlights WARNING! Halogen lamps contain pressurized gas. A bulb can explode if you: • Touch or move it when hot • Drop the bulb • Scratch the bulb Wear eye and hand protection. NOTE: To prevent a possible electrical short circuit, switch off light prior to replacing a bulb.
Page 245: Front Turn Signal And Parking/Standing Lights
Front Turn Signal and Parking/Standing Lights • Twist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Rein- stall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1.
Page 246: License Plate Light
246 MAINTAINING YOUR VEHICLE 4. Replace the access door in the trim panel. License Plate Light 1. Remove the two lens assembly mounting screws. 2. Pull the bulb out of the socket. 3. Replace the bulb and reattach the lens assembly. 4.
Page 247: Vehicle Storage
the vehicle and then readjust the headlights to the original position. If any further adjustments are neces- sary contact your manufacturer’s dealer. A detailed ser- vice procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual.
Page 248 248 MAINTAINING YOUR VEHICLE Check the battery every four to six weeks to ensure that the voltage is above 12.40. Voltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedure in the Service Manual.
Page 249: Specifications
SPECIFICATIONS Engine Specifications Engine Size 195.2 CID (3.2 Liters) Mode of Operation 4–stroke engine, gasoline injection No. of Cylinders Horsepower (SAE J 1349) 215 hp (160 kW) @ 5700 Bore 3.54 in. (89.90 mm) Stroke 3.30 in. (84.00 mm) Torque (SAE J 1349) 229 ft.
Page 250 250 MAINTAINING YOUR VEHICLE Body Specifications Overall Length 159.8 in. (4058 mm) Maximum Width 69.5 in. (1766 mm) Maximum Width With 76.9 in. (1954 mm) Mirrors Overall Height Coupe: 51.5 in. (1307 mm) Roadster: 51.8 in. (1315 mm) Front Track 58.8 in.
Page 251: Fluid Capacities
FLUID CAPACITIES Fuel (Approximate) Fuel Tank Reserve Engine Oil (with filter) 3.2 L Engine Cooling System * 3.2 L Engine Manual Transmission Automatic Transmission Rear Axle Power Steering Reservoir Brake Reservoir Windshield Washer Reservoir (MAX fill when empty) * Includes heater and coolant recovery bottle filled to MAX level. MAINTAINING YOUR VEHICLE 251 U.S.
Page 252: Recommended Fluids, Lubricants And Genuine Parts
252 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Spark Plug Gap Fuel Selection Fluids, Lubricants and Genuine Parts Use coolant approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant.
Page 253: Chassis
Chassis Component Automatic Transmission Brake Master Cylinder Clutch Fluid Manual Transmission Fluid Power Steering Reservoir Rear Axle Fluid Tire Pressure Fluids, Lubricants and Genuine Parts Only use ATF approved to MB 236.10, MB 236.12. Synthetic Dexron III Transmission Fluid may be substituted. Use brake fluid approved to MB 331.0, or a DOT 4 brake fluid with: mini- mum dry boiling point (ERBP) 500°F (260°C), minimum wet boiling point (WERBP) 356°F (180°C), maximum viscosity 1500 mm...
Page 254: Body
254 MAINTAINING YOUR VEHICLE Body Component Hinges: Door Mopar Spray White Lube Liftgate / Decklid Mopar Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Hood Springs and Links Mopar Spray White Lube Latches: Liftgate/Decklid Mopar Spray White Lube Hood/Safety Catch Mopar Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Door Mopar Spray White Lube Seat Regulator and Track Window System Components...
Page 255 MAINTENANCE SCHEDULES CONTENTS Introduction ......256 Warranty ......256 Emission Control System Maintenance .
Page 256: Introduction
256 MAINTENANCE SCHEDULES INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions.
Page 257: Emission Control System Maintenance
The use of Special lubricant additives is not recom- mended. The use of such additives may affect your warranty rights. With regard to legal stipulations con- cerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment.
Page 258: Scope Of Work For "A" Schedule Maintenance Service
258 MAINTENANCE SCHEDULES Your Flexible Service System (FSS) — see Understanding Your Instrument Panel section — should give you an exact indication of when your vehicle should be sched- uled for service and which schedule to follow. Additional Periodic Maintenance items should also be performed beyond the items listed in the following charts to assure the optimum performance of your Crossfire.
Page 259: Scope Of Work For "B" Schedule Maintenance Service
SCOPE OF WORK FOR “B” SCHEDULE MAINTENANCE SERVICE Oil Change • Change oil and replace filter Maintenance • Rotate tires • Replace dust filter (if equipped) • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check •...
Page 260: Fss System
260 MAINTENANCE SCHEDULES Fluid Levels Check fluid levels for the following systems and correct if necessary. Should there be a loss of fluid that cannot be explained by regular use, trace and eliminate the cause. • Engine cooling system (check corrosion inhibitor/ antifreeze) •...
Page 261: Regular Check-Ups
The next service is normally calculated and displayed next to the Service A or Service B symbol as distance remaining before the next service is required. Depending on operating conditions through- out the year, a clock symbol may appear next to the service symbol.
Page 262: Additional Periodic Maintenance
262 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 263 At approximately every 50,000 miles (80,000 km) or 4 years: • Check condition of driveshaft flex discs. • Retighten locking bolts for steering (observe torque). At approximately every 60,000 miles (96,000 km) or 4 years: • Replace fuel filter. • Replace air cleaner filter element. At approximately 80,000 miles (129,000 km): •...
Page 264: Special Maintenance Requirements
264 MAINTENANCE SCHEDULES SPECIAL MAINTENANCE REQUIREMENTS Coolant Have the corrosion inhibitor/antifreeze concentration in the coolant checked before the onset of winter (once a year in countries with high prevailing temperatures). Have the coolant replaced every five years or 100,000 miles (160,000 km). Dust Filter for Heating/Ventilation Replacement (If Equipped) The dust filter is replaced during routine maintenance...
Page 265: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......266 Prepare For The Appointment .
Page 266: Suggestions For Obtaining Service For Your Vehicle
266 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty;...
Page 267 This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Page 268 268 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the DaimlerChrysler Corporation has installed special TDD (Telecommunication Devices for the Deaf) equip- ment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the DaimlerChrysler Corpora-...
Page 269: Warranty Information
WARRANTY INFORMATION See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 states of the United States and Washington, D.C.: If you believe that your vehicle has a defect which...
Page 270: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 271: Tire Safety Information
TIRE SAFETY INFORMATION Tire Markings Tire Sizing Chart NOTE: P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. IF YOU NEED CONSUMER ASSISTANCE 271 NOTE: European Metric tire sizing is based on Euro- pean design standards.
Page 272 272 IF YOU NEED CONSUMER ASSISTANCE Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 273 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 274: Tire Identification Number (Tin)
274 IF YOU NEED CONSUMER ASSISTANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 275: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. IF YOU NEED CONSUMER ASSISTANCE 275 Tire and Loading Information Placard This placard tells you important information about: 1.
Page 276 276 IF YOU NEED CONSUMER ASSISTANCE Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 277 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and IF YOU NEED CONSUMER ASSISTANCE 277...
Page 278 278 IF YOU NEED CONSUMER ASSISTANCE...
Page 279 IF YOU NEED CONSUMER ASSISTANCE 279 WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
Page 281 INDEX...
Page 282 282 INDEX ABS (Anti-Lock Brake) System ... . . 111 Adding Engine Coolant (Antifreeze) ..223 Adding Fuel ......173 Aiming Headlights .
Page 283 Carbon Monoxide Warning ....47 Cargo Compartment Capacity ......175 Catalytic Converter .
Page 284 284 INDEX Disposal Engine Oil ......212 Door Locks, Automatic ....13 Drive Belts .
Page 285 Fuses ....... . 237 Garage Door Opener ..... 97 Gas Cap .
Page 286 286 INDEX Lights Airbag ......32,116 Anti-Lock Warning ....111 Back-Up .
Page 287 Mopar Parts ......208,269 Multi-Function Control Lever ....78 Occupant Restraints .
Page 288 288 INDEX Safety Checks Inside Vehicle ....48 Safety Checks Outside Vehicle ....48 Safety Information, Tire .
Page 289 Alignment ......165 Chains ......167 Changing .
Page 290 290 INDEX Washer, Adding Fluid ....220 Washing Vehicle ......230 Wheel Alignment and Balance .
Page 291 NOTES...
Page 292 NOTES...
Page 293 NOTES...
Page 294 NOTES...
Page 295 NOTES...
Page 296 NOTES...

Chrysler 2006 Crossfire Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Maintenance Schedules

If You Need Consumer Assistance

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Chrysler 2006 Crossfire

Summary of Contents for Chrysler 2006 Crossfire