Page 1: Introduction
SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Vehicle Identification Number Disclosure Label affixed to a window on your vehicle.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Theft Alarm — If Equipped ...27 Sliding Side Door ......29 Sliding Door Open Flash .
Page 11 Child Restraint ......70 Rear Seat Delete Feature (Commercial Vehicles Only) — If Equipped ......78 Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only) .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Vehicle Key You can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks.
Page 13: Key-In-Ignition Reminder
NOTE: The power window switches, radio, power outlets, and removable console (if equipped), will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 14 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated.
Page 15: Replacement Keys
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 16: General Information
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 17: Door Locks
NOTE: • The front courtesy overhead console, door courtesy and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the “defeat”...
Page 18: Power Door Locks - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 19 If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate.
Page 20: Remote Keyless Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit— If Equipped The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Door Locks feature is enabled and the Auto Unlock On Exit feature is enabled, 2.
Page 21 equipped from the factory with three button transmitters and those built with power options will be equipped with six button transmitters. Three button transmitters will provide basic UNLOCK, LOCK and PANIC functions. Three Button Transmitter THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Six button transmitters will provide functions that allow the same basic operation as the three button, but may also be used to Open/Close the optional power liftgate, left...
Page 22: To Unlock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door side of the vehicle, or twice to unlock all doors and liftgate. The illuminated entry system also turns on.
Page 23: Using The Panic Alarm
Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open/Close Left Power Sliding Door — If Equipped Press the LEFT button twice within five seconds to open/close the left power sliding door. If the button is pushed while the door is being power closed, the door will reverse to the full open position.
Page 25: General Information
vehicles so equipped. The table below explains the Lamp Flash options. (See page 169 for more information.) Function Which Turn Signal Lamps Lock Unlock 1st Left Side Press Unlock All Doors Left Side Left Side Right Side Right Side Liftgate THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 General Information This device complies with part 15 of the FCC rules and...
Page 26: Transmitter Battery Service
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart.
Page 27: Things To Know Before Starting Your Vehicle 27
3. To reassemble the transmitter case snap two halves together. Make sure there is an even “gap” between the two halves. Test transmitter operation. VEHICLE THEFT ALARM — IF EQUIPPED This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE described previously, when closing the liftgate. If some- thing has triggered the system in your absence, the horn will sound three times when you disarm the system. Check the vehicle for tampering. NOTE: •...
Page 29: Sliding Side Door
SLIDING SIDE DOOR The sliding door may be opened from the inside or the outside. Pull out on the outside handle to open the sliding door from the outside. To open the sliding door from the inside, press the button on the grab handle and open the door.
Page 30: Sliding Door Open Flash
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. Sliding Door Open Flash When the sliding door(s) are opened, the left and right exterior hazard lights will flash for 12 seconds to alert...
Page 31 The power sliding door may also be opened by pressing the switches on the overhead console or the switch located on the trim panel just in front of the sliding door. To keep your door operating properly, observe the fol- lowing guidelines.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the inside or outside door handles are used while the power sliding door is activated, the power sliding door feature will be canceled and the door must be opened or closed manually. To avoid unintentional operation of the power sliding door from the rear seats, press the button located in the overhead console to disable the switches for the rear seat...
Page 33: Child Protection Door Lock
Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. WARNING! To avoid trapping anyone in the vehicle in a colli- sion.
Page 34: Liftgate
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power sliding door will operate from the switches located on the trim panel just in front of the power sliding door, regardless of the child lock lever position. To avoid unintentional operation of the power sliding door from the rear seats, press the button located in the overhead console to disable the switches for the rear seat passen- gers.
Page 35: Power Liftgate - If Equipped
Liftgate Release Switch If the liftgate is locked and is not equipped with a powered liftgate, pressing the button on the remote keyless entry transmitter will result in the liftgate becom- ing unlocked for 30 seconds allowing you to manually access the liftgate area.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate Switch When the remote keyless entry transmitter button is pressed and the “Lamp Flash” feature is enabled, the tail lights will flash to signal that the liftgate is opening or closing.
Page 37 • The power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open or close positions it must be opened or closed manually. • If the liftgate release button is activated while the power liftgate is closing, the liftgate will reverse to the full open position.
Page 38: Seat Storage Bin Safety Warning
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. SEAT STORAGE BIN SAFETY WARNING WARNING! Always close the storage bin covers when your...
Page 39: Reinstalling Storage Bin Cover Emergency Release
NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark strap attached to the storage bin cover latching mechanism. Reinstalling Storage Bin Cover Emergency Release If the storage bin cover strap disengages from the latch, it can be reinstalled by inserting the loose end of the strap...
Page 40: Windows
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Vent Windows Switches on the driver’s door trim panel let the driver operate the two vent windows from the driver’s seat. Power Vent Window Switches Power Windows You can control either front window using switches on the driver’s door trim panel.
Page 41: Occupant Restraints
Auto Down Feature — If Equipped The driver’s window switch has an auto down feature. Press the window switch past the detent, release, and the window will go down automatically. To open the window part way, press the window switch part way and release it when you want the window to stop.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your vehicle is equipped with the Occupant Classifi- cation System (OCS) there will be a Passenger Airbag Disabled (PAD) Indicator Light located on the center of the instrument panel. Passenger Airbag Disabled Light NOTE: The front airbags have a multi stage inflator design.
Page 43: Lap/Shoulder Belts
ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the outboard seats in your vehicle are equipped with Lap/Shoulder Belts. The belt webbing retractor is designed to lock during very sudden stops or collisions.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Latch Plate Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. •...
Page 47 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats and the second row outboard seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck.
Page 49: Lap/Shoulder Belt Untwisting Procedure
Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. Positioning Latch Plate THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180°...
Page 50: Center Lap Belts
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing.
Page 51: Seat Belt Pretensioners
WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too high will apply crash forces to the abdomen, not to the stronger hip bones.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s or front passenger’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reacti- vated if the driver’s or front passenger’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
Page 53: Seat Belts And Pregnant Women
NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancies.
Page 54: Driver And Front Passenger Supplemental Restraint Systems (Srs) - Airbags
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 55 The front airbags have a multi stage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System”...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 57 If your vehicle is equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. But even in collisions where the airbags inflate, you need the seat belts to keep you in the right position for the airbags to protect you properly.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate.
Page 59 The Airbag System consists of the following: • Occupant Restraint Controller (ORC) • AIRBAG Readiness Light • Driver Airbag • Front Passenger Airbag • Window Bags above Side Windows (If Equipped) • Front Impact Sensors • Side Impact Sensors (If Equipped) •...
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. Based on the level of collision severity, the front control module determines the proper rate of inflation.
Page 61 WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE about 30 milliseconds (about one quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates.
Page 63 affect occupant classification. Also, if you fold down the rear seat, check to be sure it doesn’t touch the front passenger seat. If there is a rapid change in temperature or humidity, the OCS may not be able to properly approximate occupant size.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all sizes of properly seated adults, the airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision.
Page 65 • The Passenger Airbag Disabled (PAD) Indicator Light — If Equipped indicates to the driver and passenger when the airbag is turned OFF in the presence of a properly seated occupant. When the PAD indicator light is illuminated, the airbag is OFF. Also, when the Occupant Classification System detects ei- ther an empty seat or a weight less than the predeter- mined occupant threshold, the ORC will not illumi-...
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an acci- dent.
Page 67 If A Deployment Occurs The airbag system is designed to deploy the airbags when the ORC and impact sensors detect a moderate-to- severe collision, to help restrain the vehicle passengers, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags, front seat belt buckle pretension- ers and driver inflatable knee blocker cannot protect you in another collision. Have the airbags, front seat belt buckle pretensioners and driver inflatable knee blocker replaced by an authorized dealer as soon as possible.
Page 69: Daimlerchrysler Corporation Integrated Child Seat - If Equipped
WARNING! • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags.
Page 70: Child Restraint
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 71 Infants and Child Restraints • Safety experts recommend rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child can not sit with knees bent over the vehicles seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat.
Page 73 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. •...
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it.
Page 75 Latch Anchorages When using the tether anchorages in the outboard seat- ing positions, ensure that the strap is routed over the top of the seatback and under the head restraint between the head restraint posts. Except for bench seats with split seatbacks, when the tether anchorage is used in the center seating position, the strap should be positioned straight THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75...
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 77 seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
Page 78: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
Page 79: Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only)
infant carrier in a vehicle without rear seats. In an accident, serious injury or death may occur from the deploying passenger air bag. This vehicle is equipped with a child restraint tether anchor located on the floor, behind the front passenger seat.
Page 80 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE FACING TO THE REAR IN A VEHICLE EQUIPPED WITH THE REAR SEAT DELETE FEATURE (Com- mercial Vehicles Only). When a convertible seat is properly installed forward facing, the vehicle seat should be adjusted to the rear most position. •...
Page 81 Tether To Anchor 3. Follow the child restraint manufacturer’s directions for proper use of connecting the child restraint to the extended tether strap. 4. If necessary, raise the passenger seat head restraint to allow the tether strap to be routed under the head restraint.
Page 82: Engine Break-In Recommendations
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal ring on the vehicle tether anchor. 7. Following the child seat manufacturer’s instructions, tighten the child restraint tether strap.
Page 83: Safety Tips
While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant.
Page 84: Safety Checks You Should Make Inside The Vehicle
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Safety Checks You Should Make Inside The Vehicle Seat Belts...
Page 85: Periodic Safety Checks You Should Make Outside The Vehicle
Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure.
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......92 Inside Day/Night Mirror ....92 Automatic Dimming Mirror —...
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnect™ System ....113 Seats ....... . 119 Manual Front &...
Page 89 Lights ....... 148 Interior Lights ..... . . 149 Park Lights .
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing ....162 Overhead Console — If Equipped ... 163 Courtesy/Reading Lights .
Page 91: Understanding The Features Of Your Vehicle
Rear Cupholders ..... . 184 Storage ......186 Front Seat Storage Bin —...
Page 92: Mirrors
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. MANUAL REARVIEW MIRROR Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 93: Driver's Side Outside Mirror Auto Dimmer - If Equipped
AUTO MIRROR UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you.
Page 94: Outside Mirror - Driver's Side
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle.
Page 95: Heated Remote Control Mirrors - If Equipped
Power Mirror Switches Select a mirror and press one of the four arrows for the direction you want the mirror to move. Driver’s power mirror preselected positions can be con- trolled by the optional Driver Memory Seat Feature. Refer to “Driver Memory Seat” in section 3 of this manual.
Page 96: Hands-Free Communication (Uconnect™)
UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro-...
Page 97: Operations
UConnect™ Switches The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Headset Profile), you may not be able to use any UCon- nect™...
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for the voice on beep, which follows the Ready prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying Setup and then Phone Pairing, the following compound command can be said: Setup Phone Pairing.
Page 99 Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual.
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority.
Page 101 Call by Saying a Name • Press the “Phone” button to begin. • After the Ready prompt and the following beep, say Call. • System will prompt you to say the name of the person you want call. • After the Ready prompt and the following beep, say the name of the person you want to call.
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect™...
Page 103 Delete Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook Delete. • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
Page 104: Phone Call Features
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook List Names.
Page 105 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone.
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 107: Uconnect™ System Features
• After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Emergency and the UConnect™ system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the USA. NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico).
Page 109 Paging To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to Working with Automated Systems.
Page 110 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. •...
Page 111: Advanced Phone Connectivity
Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: •...
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names •...
Page 113: Things You Should Know About Your Uconnect™ System
• The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle. Delete UConnect™...
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some.
Page 115 Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. •...
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 119: Seats
North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Page 120: 8-Way Driver's Power Seat - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous.
Page 121: Adjustable Head Restraints - If Equipped
CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 122: Manual Reclining Seats - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HIGH or No Heat. The switch position as well as an indicator light will show when the LOW or HIGH heat is Heated seat switches Manual Reclining Seats — If Equipped The recliner mechanism control is on the outboard side of the seat.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 124: Manual Lumbar - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar — If Equipped The lumbar adjustment handle is located inboard under the armrest. To increase the support, rotate the handle down. Manual Lumbar Control Stow ’n Go Seating On vehicles equipped with Stow ’n Go seating, the second and third row seats may be folded into the floor for convenient storage.
Page 125 Load Floor Handle 3. Pull up on the seatback recliner lever located on the outboard side of the seat and fold the seatback down. To assure the seatback is latched in the folded position, additional downward pressure on the seatback may be required when folding.
Page 126 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pull rearward on the release strap located at the rear of the seat and tumble the seat forward into the storage bin. Seat Release Strap 5. Close the storage bin cover. To Unfold Second Row Seats 1.
Page 127 3. Pull up on the seatback recliner lever located on the outboard side of the seat, to return the seatback to its full upright position. Seatback Release Lever 4. Close the storage bin cover and adjust the head restraint to the desired position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To Fold Third Row Seats 1.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull release strap marked “2” to release the anchors. Release Strap 2 4. Pull release strap marked “3” and tumble the seat rearward into the storage bin. Release Strap 3...
Page 129 To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. Assist Strap 2. Pull release strap marked “1” to unlock the recliner. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 3.
Page 130 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Tailgate Mode 1.
Page 131: Easy Access Seating
WARNING! To avoid serious injury or death, never operate the vehicle with occupants in the third row seat, while in the tailgate mode. Easy Access Seating The passenger’s and driver’s side second row seats can be tilted forward for easy access to the third row seat or rear cargo area.
Page 132: Middle Quad Fold & Tumble Seat Removal
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the seat on vehicles equipped with Stow ’n Go seating, pull forward on the release strap located on the front of the seat between the seat back and seat cushion and tilt the seat fully forward. To return the seat, lower the seat and ensure that it is fully latched.
Page 133 3. Pull up on the seatback release lever located on the outboard side of the seat and fold the seatback down. If the head restraint contacts the rear of the front seat, move the front seat forward on its tracks. Seatback Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 4.
Page 134 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull the release bar located at the bottom front edge of the seat to disengage the front attachments. Release Bar Location 6. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. To reinstall the seat, remove any obstructions from the floor in front of the seat and ensure the head restraint is in its full downward position.
Page 135: 50/50 Fold & Tumble Rear Seat Removal
50/50 Fold & Tumble Rear Seat Removal 1. Lower the head restraint and pull up on release lever “1” to fold the seatback down. Release Lever Location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 2. Pull up on release lever “2” and tumble the seat fully forward.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the release strap “3” located at the bottom of the seat to disengage the front attachments. Release Strap Location 4. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. To reinstall the 50/50 rear seat, lower the head restraint to the full down position, tilt the seat forward and engage the front floor attachments, then tilt the seat rearward to...
Page 137: Passenger Bench Seats
3 – Passenger Bench Seats Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers.
Page 138: Plastic Grocery Bag Retainer
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods.
Page 139: Rear Seat Descriptions
The release lever is below the seat and is accessible from the front and back of the seat. Rear Seat Descriptions 7 Passenger Model — 2– passenger bucket seats in the second position and 3– passenger bench seat or 50/50 bench seat in the third position.
Page 140: Rear Quad And 50/50 Seating Flexibility
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Additional Storage— The 2nd and 3rd row seats installed. The 3rd row bench seat is in the full forward position on the tracks and one or both of the rear seatbacks are folded down. 4.
Page 141 2. Increased Storage— Increased storage area is provided by folding either or both seatbacks. With one seatback folded forward, rear seating for another occupant is still provided. Either or both seats may Fold and Tumble forward for more storage space. For maximum storage, remove the head restraint and place on the seat cushion, then fold the seatback over the head restraint by lifting lever “1”...
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the seat is not occupied, the seatback can be folded forward to obtain additional cargo space. To fold the seatback forward, pull the handle labeled “1” located behind the seat on the passenger side. The seatback will latch in the folded position.
Page 143: Driver Memory Seat - If Equipped
DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the Unlock button is pressed.
Page 144: Setting Memory Positions And Linking Remote
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1.
Page 145: Memory Position Recall
10. Insert the ignition key and turn the ignition switch to the ON position. 11. Select Remote Linked to Memory in the Electronic Vehicle Information Center (EVIC) and enter Yes or select Use Factory Settings from the EVIC and enter Yes .
Page 146: To Disable A Transmitter Linked To Memory
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Disable A Transmitter Linked to Memory 1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release memory button number 1. The system will recall any memory settings stored in position 1.
Page 147: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Next, push to the left the safety catch located under the front edge of the hood, near the center.
Page 148: Lights
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 inches (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Page 149: Interior Lights
Interior Lights Interior lights are turned on when a door or liftgate is opened, the keyless entry transmitter is activated, or when the dimmer control is moved to the extreme top. The interior lights will automatically turn off in about 15 minutes if any of the following occur.
Page 150 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control With the park lights or headlights on, rotating the dimmer control for the interior lights on the in- strument panel upward will in- crease the brightness of the instru- ment panel lights. Dome Light Position Rotate the dimmer control com- pletely upward to the second de-...
Page 151: Automatic Headlights - If Equipped
Automatic Headlights — If Equipped This system automatically turns your headlights ON or OFF based on ambient light levels. To turn the system ON, turn the headlight switch to the extreme counter- clockwise position. When the sys- tem is ON, the Headlight Time Delay feature is also ON.
Page 152: Headlamp Delay - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OFF or AUTO, the lights will turn off automatically until the next cycle of the ignition switch or headlight switch. The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the 3 minute delay.
Page 153: Multifunction Lever
MULTIFUNCTION LEVER Turn Signals Move the Multifunction Lever up or down and the arrows on each side of the base instrument cluster or Information Center flash to indicate proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down.
Page 154: Headlight Low/High Beam Selector Switch
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel.
Page 155 wipers will operate for several seconds after the lever is released, and then resume the intermittent interval pre- viously selected. If the end of the lever is depressed while in the OFF position, the wipers will operate for approximately two wipe cycles, then turn OFF.
Page 156: Tilt Steering Column - If Equipped
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the small lever, located behind the turn signal control, toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place.
Page 157: Rear Park Assist System - If Equipped
Traction Control Switch To turn the system back ON, press the switch a second time until the TRAC OFF indicator turns OFF. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 NOTE: • The Traction Control System indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF.
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the driver selects Reverse the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 59 inches (150 cm). A warning display above the rear window provides both visible and audible warnings indicating the range of the object.
Page 159: Adjustable Pedals - If Equipped
beeps. The tone will remain constant and both red LEDs are illuminated once the vehicle is within 12 inches (30.5 cm) of the object. The system can be turned on or off through the electronic vehicle information center (EVIC) when the vehicle is in PARK.
Page 160: Electronic Speed Control - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. •...
Page 161: To Activate
Speed Control Switches To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.
Page 162: To Resume Speed
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE speed memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the set speed memory. To Resume Speed: To resume a previously set speed, push and release the “RESUME/ACCEL”...
Page 163: Overhead Console - If Equipped
On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control. WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control.
Page 164: Sunglass Storage
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lights also turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed.
Page 165 Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the “CAL” symbol will be displayed. After completing three 360° turns in an area free from large metal or metallic objects, the “CAL”...
Page 166 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 167: Mini-Trip Computer
To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with a Compass/Mini Trip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 5 seconds.
Page 168: Electronic Vehicle Information Center (Evic) - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Step Button Push this button to cycle through all the Compass/Mini- trip Computer displays. • US/M Button Press this button to convert the display from U.S. to metric. To Reset The Display Pressing the Reset button once will clear the resettable function currently being displayed.
Page 169: Customer Programmable Features - If Equipped
• CHECK TPM SYSTEM (Refer to ”Tire Pressure Moni- tor System” in the “Starting And Operating, Tire Section”) • MEMORY SEAT DISABLED (Not in Park) — If Equipped • ADJUSTABLE PEDAL DISABLED/CRUISE GAGED • ADJUSTABLE PEDAL DISABLED/VEHICLE IN RE- VERSE •...
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE US or Metric Pressing the “STEP” button when in this display selects US or Metric. The overhead console and climate control displays will be in the selected units. Service Interval When this feature is selected a service interval between 2,000 miles (3 200 km) and 6,000 miles (9 600 km) in 500 mile (800 km) increments may be selected.
Page 171 Remote Unlock Driver’s Door 1st When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors and liftgate. When “REMOTE UNLOCK ALL DOORS”...
Page 172 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected.
Page 173: Garage Door Opener - If Equipped
Power Accessory Delay When this feature is selected, accessory power will be supplied for up to 45 seconds for the power windows, radio, power vent windows, power outlets, and remov- able center console, when the ignition switch is turned off or until the key is removed and either front door is opened.
Page 174: Programming Homelink
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 175 HomeLink Buttons 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons.
Page 176: Canadian Programming/Gate Programming
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink but- tons, begin with Programming step two. Do not repeat step one. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6 - 8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
Page 177: Using Homelink
Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the...
Page 178: Reprogramming A Single Homelink Button
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with Programming - step 2. Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1.
Page 179: Power Sunroof - If Equipped
POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Power Sunroof Controls Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open.
Page 180: Wind Buffeting
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed forward again. The sunshade can be opened manually.
Page 181: Sunroof Maintenance
the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.
Page 182: Electrical Outlet Use With Engine Off
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position.
Page 183: Convenience Tray Drawer And Cup Holders
CONVENIENCE TRAY DRAWER AND CUP HOLDERS Instrument Panel Cup Holders The instrument panel cupholders are located in a pull out drawer just below the climate controls. Front Cupholders UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 When the drawer is pulled out firmly, the arms of the cupholders will spring out.
Page 184: Convenience Tray And Optional Smoker's Package Kit
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convenience Tray And Optional Smoker’s Package Kit Located between the instrument panel cupholders is a convenience tray that has been designed to hold miscel- laneous small items. NOTE: The convenience tray should never be used for ashes without the optional ash receiver in place.
Page 185 Quad Seat Cupholder NOTE: • The quad seat cupholders will remain upright if the seat is tilted forward. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 • The quad seat cupholders are designed to break away if stepped on. To return the cupholder to its normal position, simply push the cupholder up to snap it into place.
Page 186: Storage
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’s seat. If equipped with a lock, it can be locked with the ignition key. Front Seat Storage Bin Second Row Seat Storage bins —...
Page 187: Overhead Rail System - If Equipped
Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the Unlocked position to allow greater access to the storage bin. WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched.
Page 188 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Remove Storage Bins 1. Support the bin with one hand and pull the latch handles out. 2. Twist the latch handles a ⁄ turn and pull outward to disengage the bin from the rail. 3.
Page 189: Removable Floor Console With Fold-In-Floor Seating - If Equipped
To reinstall the storage bins, place the bin in the desired location on the overhead rail, push firmly upward on the bin with one hand, while pushing in on the latch handle, twist a ⁄ turn to attach the bin to the rail. Push the latch handle down to lock the storage bin in place.
Page 190: Removable Floor Console Without Fold-In-Floor Seating - If Equipped
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Remove the floor console. To reinstall the console, open the console lid and remove the storage tray. Pull up on the release handle and slide the console forward to engage the front of the console into the floor tray.
Page 191 Removable Floor Console To remove the console use the following procedure: 1. Open the rear lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console to disengage the floor console, reinstall the storage tray and close the rear lid.
Page 192 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the console, remove the rubber mat and relocate to the alternate floor tray, slide the console forward to engage the front of the console into the floor tray. Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap”...
Page 193 2. Plug in the power cord for the cellular phone into the outlet located in the bottom of the forward console bin and reinstall the cell phone holder. 3. Place the cell phone into the holder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 CAUTION! •...
Page 194: Rear Compartment Storage Bins
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Compartment Storage Bins Your vehicle may be equipped with open storage bins located in each rear trim panel. Cargo/Tub Nets Two cargo/tub nets are available on vehicles equipped with Fold-in-Floor Seating. The cargo nets fit in the second row storage bin and the third row tub.
Page 195: Roof Luggage Rack - If Equipped
Loading Limit ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 68 kg (150 lbs), and should be uniformly distributed over the luggage rack crossbars. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Roof Rack Distribute cargo weight evenly on the roof rack crossbars.
Page 196 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To move the cross bars, loosen the thumb screws located at the upper edge of each cross bar approximately six turns, then move the cross bar to the desired position, keeping the crossbars parallel to the rack frame. Once the cross bar is in place, retighten the thumb screws to lock the cross bar into position.
Page 197: Load Leveling System
WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....205 Base Instrument Cluster ....206 Instrument Cluster With Tach .
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning ......220 Radio Data System (RDS) ....220 PTY (Program Type) Button .
Page 201 Mode ......227 Tape CD Button ..... . 227 Time Button .
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation ....259 CD Changer Control Capability — If Equipped ......261 Sales Code RB1—AM/FM Stereo Radio With DVD/GPS Navigation System .
Page 203 Operating Instructions — Video Games/Camcorders ....272 Satellite Radio — If Equipped ....272 System Activation .
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL Front Mode Control ....281 Manual Air Conditioning Operation ..285 Manual Rear Zone Climate Control —...
Page 205: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 205 INSTRUMENTS AND CONTROLS...
Page 206: Base Instrument Cluster
206 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER...
Page 207: Instrument Cluster With Tach
UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSTRUMENT CLUSTER WITH TACH...
Page 208: Premium Instrument Cluster
208 UNDERSTANDING YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER...
Page 209: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Tire Pressure Monitoring Telltale Lamp — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle...
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime will sound to alert you to turn the signals off.
Page 211 If brake failure is indicated, immediate repair is neces- sary. WARNING! Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident.
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Anti-Lock Light This light monitors the Anti-Lock Brake Sys- tem. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 213 continuously. Refer to Enhanced Driver Seat Belt Re- minder System (BeltAlert™) in the Occupant Restraints section for more information. 14. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous chime will sound for 4 minutes.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
Page 215 21. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start. If the bulb does not come when turning the key from OFF to ON, have the condition checked promptly.
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC and the OFF indicators.
Page 217: Electronic Digital Clock
25. Trip Odometer Button Press this button to change the display from odometer to trip odometer. The word TRIP will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The odometer must be in trip mode to reset.
Page 218: Two Types Of Signals
218 UNDERSTANDING YOUR INSTRUMENT PANEL you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary...
Page 219: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. RAZ Radio UNDERSTANDING YOUR INSTRUMENT PANEL 219 Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch.
Page 220: Tuning
220 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Page 221 Program Type Radio Display News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports...
Page 222: Balance
222 UNDERSTANDING YOUR INSTRUMENT PANEL Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned.
Page 223: To Set The Radio Push-Button Memory
To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
Page 224: Fast Forward (Ff)
224 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
Page 225: Pinch Roller Release
Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play.
Page 226: Seek Button
226 UNDERSTANDING YOUR INSTRUMENT PANEL If the volume control is ON, the unit will switch from radio to CD mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: •...
Page 227: Ff/Tune/Rw
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 228: Time Button
228 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability —...
Page 229: Cd Diagnostic Indicators
CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 230: Radio Operation
230 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 231 Program Type Radio Display Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 232 232 UNDERSTANDING YOUR INSTRUMENT PANEL top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it. Tuning Press the TUNE control up or down to increase or decrease the frequency.
Page 233: Cd Player Operation
both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the push- button twice. To Change From Clock To Radio Mode Press the TIME button to change the display between radio frequency and time.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept only 4–3/4 inch (12cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 235: Cd/Dvd Changer Operation
RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: •...
Page 237 MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 238: Operation Instructions - (Cd Mode For Mp3 Audio Play)
238 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For MP3 Audio Play) SEEK Button (CD Mode For MP3 Play) Pressing the SEEK + button plays the next MP3 File. Pressing the SEEK button plays the beginning of the MP3 file.
Page 239: Sales Code Rbp-Am & Fm Stereo Radio With Cassette Tape Player, Cd Player, And Optional Cd/Dvd Changer Controls
Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to 6 Disc CD/DVD Changer Manual. SALES CODE RBP—AM & FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER, AND OPTIONAL CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left...
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds.
Page 241 Program Type Radio Display Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM and Satellite (if equipped) modes.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL Tune Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Page 243: Tape Player Operation
You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 244 244 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation. Sometimes poor playback may be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year.
Page 245: Cd Player Operation
pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction. EJT Tape Press the EJT TAPE button and the cassette will disen- gage and eject from the radio. Metal Tape Selection (70µs) If a standard 70 µ...
Page 246 246 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio off, the display will show CD and the time of day will be displayed.
Page 247: Cd/Dvd Changer Operation
Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the top of the SEEK button to move to the next randomly selected track.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the currently playing compact disc in random order to provide an interesting change of pace.
Page 249: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER NOTE: The radio sales code is located on the lower left side of your radio faceplate. RBQ Radio UNDERSTANDING YOUR INSTRUMENT PANEL 249 Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume.
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. CD’s may remain in the player while in the Satellite Radio mode. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
Page 251 Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed.
Page 252: Cd Player Operation
252 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / Volume control pushed ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 only.
Page 253 Radio display will show “ejecting” when it is being ejected. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD.
Page 254 254 UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button repeatedly within 5 seconds will allow the program format type to be selected.
Page 255 Program Type Radio Display Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode.
Page 256: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
256 UNDERSTANDING YOUR INSTRUMENT PANEL A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. CD ERROR will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 257: Radio Operation
Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 258 258 UNDERSTANDING YOUR INSTRUMENT PANEL stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE.
Page 259: Understanding Your Instrument Panel 259
General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 260 260 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
Page 261: Cd Changer Control Capability
Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. A CD or tape may remain in the player while in the Satellite mode. Time Press the TIME button to change the display from elapsed CD playing time to time of day.
Page 262 262 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s...
Page 263: Sales Code Rb1-Am/Fm Stereo Radio With Dvd/Gps Navigation System
SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM RB1 Radio UNDERSTANDING YOUR INSTRUMENT PANEL 263 The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navi- gation User’s Manual”...
Page 264: Remote Control Operating Instructions
264 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Operating Instructions NOTE: Aim the remote control at the radio located on the center of the instrument panel and press the desired button. Direct sunlight or objects blocking the line of sight may affect the function of the remote control. Remote Control...
Page 265: Headphone Transmitter Button (1)
Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13.
Page 266: Rtn Button (4)
266 UNDERSTANDING YOUR INSTRUMENT PANEL RTN Button (4) This button only functions in CD/DVD mode. Press this button to return to the previous menu when in the disc menu mode. SETUP Button (5) This button only functions in CD/DVD mode. Press the button after pressing the STOP button to access the set up menu.
Page 267: Prog Up/Down Buttons (10, 11)
PROG UP/DOWN Buttons (10, 11) PROG UP selects the next disc loaded in the changer. PROG DOWN selects the previous disc loaded in the changer. SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video. If the DVD is paused, pressing this button will advance the video frame by frame.
Page 268: Enter Button (17)
268 UNDERSTANDING YOUR INSTRUMENT PANEL ENTER Button (17) This button only functions in DVD video mode. Use the ENTER button to enter selections from the menu screens. Use the arrow buttons to toggle through the menu screen options. Light Button (18) Pressing this button illuminates the buttons on the re- mote control.
Page 269 1. Screen Width Button Changes the width of the screen picture. 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. UNDERSTANDING YOUR INSTRUMENT PANEL 269 Video Screen Controls...
Page 270: Operating Instructions - Headphones
270 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones Headphone Controls 1. Power Button 2. Volume Control 3. Power Indicator Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: •...
Page 271 Headphone Battery Service • Replace the battery in each earpiece and reinstall the cover. The headphones require two AAA batteries. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause UNDERSTANDING YOUR INSTRUMENT PANEL 271 harmful interference and (2) This device must accept any...
Page 272: Operating Instructions - Mp3 Player, Portable Walkman
272 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — MP3 Player, Portable Walkman An MP3 player can be connected to the audio system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer. NOTE: Follow the manufactures instructions for the correct colors when connecting the RCA cables.
Page 273: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
2. Credit card information. 3. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, REV and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depend-...
Page 274: Selecting Satellite Mode In Rbp, Rbu, Raz, Rb1 And Rbq Radios
274 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word SIRIUS appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds.
Page 275: Storing And Selecting Pre-Set Channels
Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio.
Page 276: Reception Quality
276 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 277: Radio Operation
The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume.
Page 278: Cd Player
278 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play.
Page 279: Cd/Dvd Disc Maintenance
turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette. As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette.
Page 280: Climate Controls
280 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Manual Air Conditioning and Heating Controls Front Blower Control The Front Blower Control selects whether the Cli- mate Control System is ON or OFF.
Page 281: Understanding Your Instrument Panel 281
Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. Dual Zone Temperature Control This is accomplished by having a separate temperature control lever for both the driver and front seat passenger.
Page 282 282 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Panel Outlets Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 283 Bi-Level Mode Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 284 284 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 285: Manual Air Conditioning Operation
Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or UNDERSTANDING YOUR INSTRUMENT PANEL 285 Defrost modes are selected.
Page 286 286 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the A/C air filter, if so equipped, and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator.
Page 287 A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON. The frequent use of outside air will help keep odors from building up within the air conditioner- heater housing.
Page 288: Manual Rear Zone Climate Control - If Equipped
288 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Rear Zone Climate Control — If Equipped The Manual Rear Zone Climate Control system has floor air outlets to the rear of the right side sliding door and overhead outlets at each outboard rear seating position. The unit provides warm or cool air through the floor and upper outlets.
Page 289 The center knob on the front climate control unit has five positions, “REAR”, “OFF”, and a range of blower speeds. Only when the primary control for the rear blower is in the “REAR” position do the second seat occupants have control of the rear blower speed.
Page 290: If Equipped
290 UNDERSTANDING YOUR INSTRUMENT PANEL in the cold position, cold air will be delivered from the headliner outlets. As the rear temperature knob is turned towards hot, the air will get warmer, and the air will be delivered from both the headliner and floor outlets.
Page 291 Three-Zone Automatic Temperature Control Operation of the system is quite simple. Begin by press- ing the auto rocker switch to the “HI” or “LO” position, the word “AUTO” will illuminate in the front ATC display along with “HI” or “LO”. The system will then automatically regulate the amount of air flow.
Page 292 292 UNDERSTANDING YOUR INSTRUMENT PANEL To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off and “DELAY” will appear in the front ATC display until the engine warms up. Also, an estimate of the time remaining until the “DELAY”...
Page 293 NOTE: Each of these features operate independently from each other. If any one feature is controlled manually, the remaining features will continue to operate automati- cally. The left blower control knob can be set to any fixed blower speed by rotating the knob from low to high. The fan will now operate at a fixed speed until additional speeds are selected or either the Auto HI or Auto LO buttons are pressed.
Page 294 294 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode Bi-Level Outlets Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 295 Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. UNDERSTANDING YOUR INSTRUMENT PANEL 295 Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 296 296 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: While operating in either Auto HI or Auto LO , the system will not automatically sense the presence of fog, mist, or ice on the windshield.
Page 297 Recirculation Control When outside air contains smoke, odors, high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the recirculation button. The recirculation mode should only be used temporarily. The recirculation symbol will illuminate in the display when this button is selected.
Page 298 298 UNDERSTANDING YOUR INSTRUMENT PANEL “AUTO”. Only when the “REAR SYSTEM” knob is in the “REAR CONTROL” position do the second seat occu- pants have control of the Rear Automatic Temperature Control System. The Rear Automatic Temperature Control System is located in the headliner near the center of the vehicle.
Page 299 • The temperature can be displayed in U.S. or Metric by selecting the US/M customer programmable feature. Refer to the “Overhead Console-Customer Program- mable Features” in Section 3 of this manual. Rear Blower Control The rear blower control, located in the headliner near the center of vehicle “AUTO”...
Page 300 300 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Mode Control The Rear Mode Control, located in the headliner near the center of the vehicle can be used to select between Auto, Headliner, Bi- Level and Floor modes. Auto Mode The rear system automatically maintains the correct mode and comfort level desired by the rear seat occu- pants.
Page 301 glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used.
Page 302: Rear Window Features
302 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter — If Equipped The climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to MAINTAINING YOUR VEHICLE, “Air Conditioner Maintenance”...
Page 303: Rear Washer Operation - Manual Temperature Control Only
Rear Washer Operation — Manual Temperature Control Only The controls are located on the Manual Tempera- ture Control head above the front blower control. Press and hold the button for as long as spray is desired. If the button is depressed and held while the Intermittent wiper is on, the wiper will operated for a few seconds after the button is released, then resume inter- mittent operation.
Page 304: Intermittent Rear Wiper Operation - Automatic Temperature Control Only
304 UNDERSTANDING YOUR INSTRUMENT PANEL Intermittent Rear Wiper Operation — Automatic Temperature Control Only When this button is pressed and the ignition switch is in the ON position, the rear wiper will operate at a fixed interval of about 8 seconds. As vehicle speed increases, the time delay will shorten.
Page 305: Electric Rear Window Defroster - If Equipped
Washer Fluid Reservoir The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates. UNDERSTANDING YOUR INSTRUMENT PANEL 305 Electric Rear Window Defroster — If Equipped Press this button to turn on the rear window defroster and the optional heated mirrors.
Page 306 306 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. Labels can be peeled off after soaking with warm water.
Page 307: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 310 Normal Starting ..... . 310 Extremely Cold Weather (Below 29°...
Page 308 308 STARTING AND OPERATING Tire Markings ......324 Tire Identification Number (TIN) ..327 Tire Loading And Tire Pressure .
Page 309 Fuel System Cautions ....348 Carbon Monoxide Warnings ....349 Adding Fuel .
Page 310: Starting Procedures
310 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather;...
Page 311: If Engine Fails To Start
WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 312: After Starting
312 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released.
Page 313: Automatic Transmission
WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. STARTING AND OPERATING 313 AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
Page 314: Brake/Transmission Interlock System
314 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 315 Reset Mode - Electronic Transmission The transmission is monitored electronically for abnor- mal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into sec- ond gear. The transmission remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.
Page 316 316 STARTING AND OPERATING “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive For most city and highway driving, it provides smoothest upshifts and downshifts and best fuel economy.
Page 317: Parking Brake
PARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position.
Page 318: Brake System
318 STARTING AND OPERATING added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 319: Anti-Lock Brake System - If Equipped
by increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Lamp. Anti-Lock Brake System — If Equipped The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions.
Page 320 320 STARTING AND OPERATING When the vehicle is driven over approximately 15 mph (25 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly.
Page 321: Power Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 322: Traction Control - If Equipped
322 STARTING AND OPERATING Upon initial start-up in cold weather, the power steering pump may make noise for a short period of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and does not in any way damage the steering system.
Page 323 The system is always in the “stand by” mode unless, • The Traction Control Switch has been used to turn the system OFF Traction Control Switch • There is a Traction Control System malfunction STARTING AND OPERATING 323 • The system has been deactivated to prevent damage to the brake system due to overheated brake tempera- tures NOTE:...
Page 324: Tire Safety Information
324 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 325 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 326 326 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 327: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 328: Tire Loading And Tire Pressure
328 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 329 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading...
Page 330 330 STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb.
Page 331 STARTING AND OPERATING 331...
Page 332: Tires-General Information
332 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 333: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 334 334 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 335: Radial-Ply Tires
loading may be required for high speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
Page 336: Compact Spare Tire - If Equipped
336 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 337: Limited Use Spare - If Equipped
Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
Page 338: Tread Wear Indicators
338 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 339: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 340: Alignment And Balance
340 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, result- ing in changes to steering, handling, and braking of your vehicle.
Page 341: Tire Pressure Monitor System - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE PRESSURE MONITOR SYSTEM — IF EQUIPPED The Tire Pressure Monitor System (TPMS) system uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels (EXCLUDING THE SPARE TIRE).
Page 342 342 STARTING AND OPERATING CAUTION! The TPMS system has been optimized for the origi- nal equipment tires and wheels. TPMS system pres- sures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 343: General Information
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 344: Snow Tires
344 STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
Page 345: Tire Rotation Recommendations
Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions.
Page 346: Fuel Requirements
If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 347: Gasoline/Oxygenate Blends
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle.
Page 348: Materials Added To Fuel
348 STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
Page 349: Carbon Monoxide Warnings
Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 350: Adding Fuel
350 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Fuel Filler Cap (Gas Cap) CAUTION! Damage to the fuel system or emission control...
Page 351 NOTE: • Tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer.
Page 352: Vehicle Loading
352 STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. If seats are removed for carrying cargo, do not exceed the specified GVWR and GAWR.
Page 353: Overloading
WARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory...
Page 354: Trailer Towing
354 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. Example Only Empty Weight Load (Including driver, pas- sengers and cargo) Total GAWR TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 355: Common Towing Definitions
Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
Page 356 356 STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer.
Page 357: Trailer Hitch Classification
Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
Page 358 358 STARTING AND OPERATING Engine/Transmission GCWR (Gross Com- bined Wt. Rating) 3.3L & 3.8L Auto- 6,600 lbs (2993 kg) matic 6,600 lbs (2993 kg) 6,600 lbs (2993 kg) Frontal Area Max. GTW (Gross Trailer Wt.) 40 SQ. FT. (3.72 Up to 2 persons & square meters) Luggage 1,800 lbs (816 kg)
Page 359: Trailer And Tongue Weight
Engine/Transmission GCWR (Gross Com- bined Wt. Rating) 3.3L & 3.8L Auto- 8,600 lbs (3900 kg) matic with trailer tow package 8,600 lbs (3900 kg) 8,600 lbs (3900 kg) * For vehicles equipped with Fold-in-Floor seating, the Gross Trailer Weight must be reduced by 100 lbs (45 kg). Refer to local laws for maximum trailer towing speeds.
Page 360 360 STARTING AND OPERATING which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: •...
Page 361: Towing Requirements
Towing Requirements To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- mended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. •...
Page 362 362 STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners.
Page 363 − When replacing tires refer to the Tires–General Infor- mation section of this manual on Replacement Tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements — Trailer Brakes −...
Page 364 364 STARTING AND OPERATING WARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance.
Page 365: Towing Tips
7 - Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. STARTING AND OPERATING 365 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3”...
Page 366: Recreational Towing (Behind Motorhome, Etc.)
366 STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
Page 367: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....368 If Your Engine Overheats ....369 Jacking And Tire Changing .
Page 368: Hazard Warning Flasher
368 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the radio. Hazard Flasher Switch To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 369: If Your Engine Overheats
IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed.
Page 370: Jacking And Tire Changing
370 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Page 371: Jacking Instructions - Stow 'N Go Seating
Jacking Instructions — Stow ’n Go Seating Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK. Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 372 372 WHAT TO DO IN EMERGENCIES Jack Location — Stow ’n Go Seating The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Pull up on the lever to release the cover. Jack Location Remove the scissors jack and jack handle by rotating the small wing nut to the left.
Page 373 WHAT TO DO IN EMERGENCIES 373 Spare Tire Stowage — Stow ’n Go Seating For vehicles equipped with Stow ’n Go seating, the spare tire is stowed inside a protective cover located under the center of the vehicle by means of a cable winch mecha- nism.
Page 374 374 WHAT TO DO IN EMERGENCIES Jacking Instructions — Stow ’n Go Seating 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T’...
Page 375 CAUTION! The winch mechanism is designed for use with the winch “T” handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Assemble the winch handle extensions to form the Spare Tire Hook and pull the compact spare tire/cover assembly from under the vehicle.
Page 376 376 WHAT TO DO IN EMERGENCIES NOTE: If either front tire is flat, it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle. Refer to jack engagement locations in the following steps for proper jack placement.
Page 377 WHAT TO DO IN EMERGENCIES 377 Jack Engagement Locations...
Page 378 378 WHAT TO DO IN EMERGENCIES 6. These locations are on the sill flange of the body and consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs closest to the wheel to be changed. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
Page 379 10. Lower the vehicle by turning the jack screw to the left. 11. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station.
Page 380 380 WHAT TO DO IN EMERGENCIES 14. Stow the cable and wheel spacer before driving the vehicle, reassemble the winch handle extensions to form a “T’ and fit the winch “T” handle over the drive nut. Rotate the nut to the right approximately 33 turns until the winch mechanism clicks at least three times.
Page 381 WHAT TO DO IN EMERGENCIES 381 WARNING! A loose compact spare tire/cover assembly, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the com- pact spare tire with the cover assembly in the place provided.
Page 382 382 WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the Spare Tire Hook and pull the wheel spacer from under the vehicle. 3. Turn the compact spare tire so that the valve stem is down and place the tire into the spare tire cover assem- bly.
Page 383: Jacking Instructions - Non Stow 'N Go Seating
CAUTION! For vehicles equipped with Stow ’n Go seating, the Winch Mechanism is designed specifically to stow a COMPACT Spare Tire ONLY. Do not attempt to use the Winch to stow the Full Size ’Flat’ Tire, or any other Full Size Tire. Vehicle damage may result. Jacking Instructions —...
Page 384 384 WHAT TO DO IN EMERGENCIES Jack Location — Non Stow ’n Go Seating The jack, jack handle are stowed behind the rear left side trim panel in the rear cargo area. Pull up on the lever to release the cover. Remove the spare wheel, scissors jack and jack handle from stowage by rotating the wing nut to the left.
Page 385 Lowering Spare Tire Jacking Instructions — Non Stow ’n Go Seating 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. WHAT TO DO IN EMERGENCIES 385 2.
Page 386 386 WHAT TO DO IN EMERGENCIES Jack Engagement Locations...
Page 387 5. These locations are on the sill flange of the body and consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs closest to the wheel to be changed. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
Page 388 388 WHAT TO DO IN EMERGENCIES NOTE: Do not install the wheel cover on the compact spare. Do not use a hammer or force to install the wheel covers. 9. Lower the vehicle by turning the jack screw to the left. 10.
Page 389: Jump-Starting Procedures If Battery Is Low
• For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle. • Using the jack handle, rotate the drive nut to the right until the wheel is drawn into place against the underside of the vehicle.
Page 390 390 WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmis- sion cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 391: Driving On Slippery Surfaces
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery.
Page 392: Freeing A Stuck Vehicle
392 WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 393: Towing A Disabled Vehicle
TOWING A DISABLED VEHICLE With Ignition Key Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), and the towing speed must not exceed 44 mph (72 km/h).
Page 394: Without The Ignition Key
394 WHAT TO DO IN EMERGENCIES If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transmission remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 395 MAINTAINING YOUR VEHICLE CONTENTS 3.3L/3.8L Engines ..... . 398 Onboard Diagnostic System — OBD II ..399 Emissions Inspection And Maintenance Programs .
Page 396 396 MAINTAINING YOUR VEHICLE Steering Linkage ..... . 413 Drive Shaft Universal Joints ....413 Body Lubrication .
Page 397 Center High Mounted Stop Light (CHMSL) . . . 443 License Light ......443 Fluids And Capacities ....444 MAINTAINING YOUR VEHICLE 397 Fluids, Lubricants And Genuine Parts .
Page 398: 3.3L/3.8L Engines
398 MAINTAINING YOUR VEHICLE 3.3L/3.8L ENGINES Engine Compartment 3.3L/3.8L Engines...
Page 399: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 400: Emissions Inspection And Maintenance Programs
400 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 401: Replacement Parts
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
Page 402: Maintenance Procedures
402 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
Page 403 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 404 404 MAINTAINING YOUR VEHICLE Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). •...
Page 405 American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures.
Page 406: Engine Oil Filter
406 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
Page 407: Spark Plugs
Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the cata- lytic converter.
Page 408 408 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
Page 409: Maintenance-Free Battery
In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating. If this occurs, the vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Thereafter, service, including a tune-up to manufacturer’s specifications, should be ob- tained immediately.
Page 410 410 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 411: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time.
Page 412: Power Steering - Fluid Check
412 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 413: Front Suspension Ball Joints
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 414: Body Lubrication
414 MAINTAINING YOUR VEHICLE Continued operation could result in failure of the univer- sal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate, sliding doors and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
Page 415: Windshield And Rear Window Washers
Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 416: Cooling System
416 MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 417 Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 418 418 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 419 The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
Page 420 420 MAINTAINING YOUR VEHICLE do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate.
Page 421: Hoses And Vacuum/Vapor Harnesses
• Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.
Page 422: Brakes
422 MAINTAINING YOUR VEHICLE Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure. Brakes In order to assure brake system performance, all brake system components should be inspected periodically.
Page 423: Master Cylinder - Brake Fluid Level Check
Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings.
Page 424 424 MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear.
Page 425: Fuel System Hoses
Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses which have unique material charac- teristics to provide adequate sealing and resist attack by deteriorated gasoline. Use only the manufacturers specified hoses in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service.
Page 426 426 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Page 427 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips.
Page 428: Front And Rear Wheel Bearings
428 MAINTAINING YOUR VEHICLE Severe Usage is defined as: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules.
Page 429 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: •...
Page 430 430 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
Page 431 • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle.
Page 432 432 MAINTAINING YOUR VEHICLE Cleaning High Gloss Front Door B-pillar Appliques When cleaning the front door B-pillar appliques, care must be taken to avoid scratching the plastic. 1. Remove all dirt with a wet soft rag. A mild soap solution may be used, do not use high alcohol content or abrasive cleaners.
Page 433: Cleaning The Instrument Panel And Underseat Cup Holders
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 434: Integrated Power Module (Ipm)
434 MAINTAINING YOUR VEHICLE Cleaning Soak the drawer, with the drawer front facing up, in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour. After one hour pull the drawer from the water and dip it back into the water about six times.
Page 435 Cavity Maxi Fuse Description 30 Amp Front Wipers Pink 40 Amp Anti-Lock Brake System Green (ABS) Pump 40 Amp Front Blower Green 40 Amp Electronic Back Light (EBL) Green 40 Amp Body Control Module Green (BCM) Feed 1 30 Amp Central Amplifier Pink 30 Amp...
Page 436 436 MAINTAINING YOUR VEHICLE Cavity Mini Fuse 20 Amp Yel- Fog Lights 15 Amp Blue Left Park/Tail Light 15 Amp Blue Right Park/Tail Light 20 Amp Yel- RDO/IP Ignition 20 Amp Yel- 12 Volt Out Ignition or Battery 20 Amp Yel- Horn 20 Amp Yel- EWD/ Rear Wiper...
Page 437: Vehicle Storage
CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 438: Replacement Light Bulbs
438 MAINTAINING YOUR VEHICLE • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
Page 439: Bulb Replacement
BULB REPLACEMENT Headlights 1. Remove the three screws securing the headlight mod- ule. 2. Turn the bulb socket retaining ring or the bulb assem- bly counterclockwise. MAINTAINING YOUR VEHICLE 439 3. Disconnect the electrical connector and replace the bulb. NOTE: On some vehicles it may be necessary to slide the red release lock rearward and push forward on the connector while depressing the release tab.
Page 440: Front Park/Turn Signal And Sidemarker Lights
440 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Front Park/Turn Signal and Sidemarker Lights 1.
Page 441: Front Fog Light
2. Twist the turn signal socket to remove from the headlight module and pull bulb from socket. 3. Replace bulb, reinstall socket and then reinstall the headlight module. MAINTAINING YOUR VEHICLE 441 Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2.
Page 442: Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights
442 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly push-in type fasteners, by prying under the fastener head with a large flat screwdriver. 3. Squeeze the socket assembly tabs to remove it from the housing.
Page 443: Center High Mounted Stop Light (Chmsl)
Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. MAINTAINING YOUR VEHICLE 443 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
Page 444: Fluids And Capacities
444 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 87 Octane Engine Oil-with filter 3.3 & 3.8 Liter Engines (SAE 5W-20, API Certified) Cooling System * 3.3 & 3.8 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 445: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Oil Filter 3.3/3.8 liter engines Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent Use API Certified SAE 5W-20 engine oil. Refer to your oil filler cap for cor- rect SAE grade, meeting DaimlerChrysler Material Standard MS-6395.
Page 446: Chassis
446 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 447: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..448 Maintenance Schedules ....448 Schedule “B” ......451 Schedule “A”...
Page 448 448 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 449 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: Most vehicles are operated under the conditions listed for Schedule B . Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule B .
Page 450 450 MAINTENANCE SCHEDULES • Check all lights and all other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints and front suspension compo- nents.
Page 451 SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 452 452 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Replace the air conditioning filter. 3, 000 6, 000 9, 000...
Page 453 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the air conditioning filter.
Page 454 454 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Replace the air conditioning filter. 39, 000 42, 000 45, 000...
Page 455 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 456 456 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs on 3.3 liter and 3.8 liter engines.
Page 457 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter * Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 458 458 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 459 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 460 460 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs on 3.3 liter and 3.8 liter engines. Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 461 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Replace the air conditioning filter.
Page 462 462 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check the PCV valve and replace, if neces- sary.* Inspect the serpentine drive belt on 3.3 liter...
Page 463 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter en- gines, replace if necessary.
Page 464 464 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 465 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 466 466 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 467: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......468 Prepare For The Appointment .
Page 468: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 469 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 470 470 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 471: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 472: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 473: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 474: Temperature Grades
474 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory...
Page 475 INDEX...
Page 476 476 INDEX Adding Fuel ......350 Adding Washer Fluid ....304,415 Additives, Fuel .
Page 477 Interlock System ..... . . 314 Reset Mode ......315 Selection Of Lubricant .
Page 478 478 INDEX Caps, Filler Fuel ....... . 350 Oil (Engine) ......405 Radiator (Coolant Pressure) .
Page 479 Compass Variance ..... . . 166 Computer, Trip/Travel ....167 Console, Overhead .
Page 480 480 INDEX Door Locks ......17 Door Locks, Automatic ....19 Door Opener, Garage .
Page 481 Temperature Gauge ..... 213 Exhaust Gas Caution ....37,83,349,416 Exhaust System .
Page 482 482 INDEX Octane Rating ..... . 346,445 Requirements ..... . 346,444 Tank Capacity .
Page 483 Hitches Trailer Towing ......357 HomeLink (Garage Door Opener) Transmitter . . . 173 Hood Release ......147 Hook, Coat .
Page 484 484 INDEX Lap/Shoulder Belts ..... . . 43 LATCH (Lower Anchors and Tether for CHildren) . 74 Latches Hood ....... 147 Lead Free Gasoline .
Page 485 Reading ......163 Rear Servicing ......442 Rear Tail .
Page 486 486 INDEX Automatic Dimming ..... 92 Electric Remote ......94 Exterior Folding .
Page 487 Overheating, Engine ....213,369 Owner’s Manual (Operator Manual) ..4,472 Panic Alarm ......23 Parking Brake .
Page 488 488 INDEX Radio Remote Controls ....264,276 Radio, Satellite ......272 Radio (Sound Systems) .
Page 489 Schedule, Maintenance ....448 Seat Belt Maintenance ....433 Seat Belt Reminder .
Page 490 490 INDEX Shoulder Belts ......43 Signals, Turn ....153,210,440,442 Sliding Door .
Page 491 Temperature Gauge, Engine Coolant ..213,369 Tether Anchor, Child Restraint ....74 Theft Alarm (Security Alarm) ....27 Theft System Arming .
Page 492 492 INDEX Disabled Vehicle ..... . . 393 Guide ......357 Recreational .
Page 493 Vanity Mirrors ......95 Variance, Compass ..... . . 166 Vehicle Certification Label .
Page 494 494 INDEX...
Page 495 NOTES...
Page 496 NOTES...

This manual is also suitable for:

Town and country 2006

Chrysler 2006 Town and Country Instruction Manual

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2006 Town and Country

Summary of Contents for Chrysler 2006 Town and Country