Related Manuals for Living & Co Takiwira Series
Summary of Contents for Living & Co Takiwira Series
- Page 1 Tākiwira 5 Drawer Tallboy 98cm 102cm 39.6cm INSTRUCTION MANUAL Maximum recommended weight is 15kgs per drawer Job no.
- Page 2 Assembly Details Floor Area 3m x 4m Required Assembly Space Approximate Assembly Time 1 Person Assembly Tools Required AFTER SALES SUPPORT www.compacfurniture.co.nz or 0800 100 858...
- Page 3 Tips before you start 1. For the protection of your furniture, we recommend that the product is placed on a protected surface during assembly to prevent damage 2. Please check that all parts are present before you start the assembly of your furniture 3.
- Page 4 Parts List PART MEASUREMENTS NOTES 980 x 396 x 25mm Laminate on one side LH End 994 x 390 x 15mm Laminate on both sides RH End 994 x 390 x 15mm Laminate on both sides Division 194 x 360 x 15mm Laminate on front edge Toeboard 938 x 80 x 15mm...
- Page 5 Cam Installation & Operation Guide The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. Press the cam fitting into the hole provided. The arrow on the top of the cam must point to the connecting hole in the edge of the board.
- Page 6 Assembly STEP 1: Top To begin assembly, lay the top finished side down on a clean and clear surface • Screw six Connecting Bolts into the holes as shown • Using the Panhead screw, attach the Safety Strap as shown by screwing it first through the •...
- Page 7 STEP 2: LH End Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each • slide (ensure that the end of the slide with the wheel is on the side with the finished edge). Insert two Large Cams as shown (make sure the arrow on the top of the Cam points towards the •...
- Page 8 STEP 3: RH End • Repeat the previous step with the RH End. Dowel Dowel Connecting Bolt Drawer Slide Screw Drawer Slide Screw Connecting Bolt (Screw through the hole in) Large Cam Connecting Bolt Drawer Slide Screw Connecting Bolt Connecting Bolt STEP 4: Division Install the two Large Cams into the Division as shown below –...
- Page 9 STEP 5: Rails Your pack will contain 4 boards the same size. • 1 x Toeboard • 3 x Rails Install two Large Cams into each piece as indicated • Push the Dowels into each of the boards as indicated •...
- Page 10 STEP 7: Attach RH End Turn the LH End with the Rails and Toeboard attached onto its back edge. • Fit the RH End to the Rails and Toeboard as shown in the drawing below. • Lock the RH End to the Rails and Toeboard by tightening all the Cams in the Rails and •...
- Page 11 STEP 7: Attach Top and Glide Feet Turn the Top with the Division attached on its back edge. Fit in onto the top of the ends as shown • below. The connecting Bolts in the Top will fit down into the Cams in the Ends. •...
- Page 12 STEP 10: Back Panel • Turn the Tallboy onto its front edge. Make sure the surface is clear and free of anything that may damage the laminate finish. • Slide the Back Panel in place (please ensure that the end with the predrilled holes part way down the panel is at the top) •...
- Page 13 Assemble the Small Drawers Your Tākiwira Tallboy will have two shallow top drawer and four deeper bottom drawers. Begin with assembling the small drawers. Drawer Bottom LH Drawer Side Drawer Back RH Drawer Side Drawer Front STEP 11: Install Hardware Small Cam Dowell Connecting...
- Page 14 STEP 12: Assemble the Drawer Lay the Drawer Front finishes side down on a smooth, clean surface. • Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in • the Drawer Front. Turn the Small Cams in a clockwise direction to lock the Drawer Sides in place.
- Page 15 STEP 13: Attach the Drawer Slides • Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the Drawer Front.
- Page 16 STEP 14: Install the Hardware (large drawers) Install the hardware in the Drawer Parts as shown below. • Connecting Bolt Connecting Bolt Connecting Bolt DRAWER FRONT Small Cam DRAWER BOTTOM SUPPORT Dowel Small Small LH DRAWER SIDE Dowel RH DRAWER SIDE STEP 15: Install the Hardware (large drawers) Lay the Drawer Front face down on a smooth, clean surface •...
- Page 17 STEP 16: Attach Drawer Back Fit the Drawer Bottom Support into place underneath the Drawer Bottom, the Connecting Bolt in the • centre back of the Drawer Front will fit up into the Small Cam. • Turn the Small Cam in a clockwise direction to lock the Drawer Bottom Support in place. •...
- Page 18 STEP 18: Attach the Handles and Insert the Drawers Attach the Bar Handles to the Drawer Front using the screws provided • Fit the drawers into the Bedside. • Angle the drawer slightly to ensure that the wheel at the back of the drawer slide goes behind the front wheel on the cabinet slide.
- Page 19 STEP 12: Attach the Handle and Insert the Drawers Compac Furniture strongly recommends using a safety strap on all furniture, especially if small children are around. Secure your unit to the wall using the Safety Strap and a screw suitable for your wall (not supplied). We recommend you screw into a stud.
- Page 20 WARRANTY We pride ourselves on producing a range of quality products that are both packed with features and completely reliable. We are so confident in our products, we back them up with a five-year warranty. Now you too can relax knowing that you are covered.