elero RolTop Operating And Installation Instructions
elero RolTop Operating And Installation Instructions

elero RolTop Operating And Installation Instructions

Roller shutter drive

Advertisement

Quick Links

Roller shutter drive RolTop
120 V / 60 Hz

Table of contents

Operating and installation
1
instructions
2
2.1
2.2
2.3
2.4
2.5
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
5
5.1
5.2
5.3
5.4
5.5
5.6
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.6.7
5.6.8
5.6.9
Upper end position freely confi gurable,
5.7
Technical data
6
Troubleshooting
1
7
Servicing
8
Cleaning
1
9
Repair
1
10
Address
2
11
Disassembly and disposal
2
12
EC Declaration of Conformity
2
13
US: Addendum to the manual
2
UL approval
2
14
CA: Addendum au manuel
2
Homologation UL
2
15
Technical data and dimensions
3
3
Roller shutter drive RolTop
3
120 V / 60 Hz
3
1
Operating and installation
4
instructions
4
Please keep these operating instructions for later use and
have them available during the complete service life of the
4
product!
4
The German version of these operating instructions is
the original version.
4
All foreign language documents are translations of the
5
original version.
5
All rights reserved with regard to patent claim or submission
of design or utility patent.
6
2

General information

6
The structure of these operating instructions is based on
6
the service life phases of the electrical drive (subsequently
referred to as product).
6
The manufacturer reserves the right to make changes to the
6
technical data included in these operating instructions. The-
se may deviate from the respective model of the product
6
while the factual information are generally not changed and
are not losing their validity. The current state-of-the-art can
6
be obtained from the manufacturer at all times. Potential
claims cannot be asserted. Deviations from text and pictori-
6
al statements are not possible and depending on the tech-
nical development, setup and accessories of the product.
7
Deviating information on special models are included by the
manufacturer in the sales documentation. Other information
shall remain unaffected by this.
7
2.1

Standards and guidelines

During system design, basic safety and health requirements
7
of applicable laws, standards and guidelines were obser-
ved. The safety is confi rmed by means of the Declaration
7
of Conformity (refer to „EC Declaration of Conformity"). All
safety information in these operating instructions are based
on currently applicable laws and regulations in Germany.
All information in the operating instructions must be obser-
8
8
8
8
8
8
8
8
9
9
9
10
138183901_US+CA_1114

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RolTop and is the answer not in the manual?

Questions and answers

Summary of Contents for elero RolTop

  • Page 1: Table Of Contents

    Electrical connection All rights reserved with regard to patent claim or submission of design or utility patent. Connection example, RolTop 120 V / 60 Hz General information Parallel connection The structure of these operating instructions is based on...
  • Page 2: Intended Use

    In case of a defect, the product may only be repaired by the manufacturer. Please refer to section „Address“ for the return address of the customer service. If you did not acquire the product directly from elero, please contact your supplier. 2 | US+CA ©...
  • Page 3: General Safety Principles

     Without approval by the manufacturer, no modifi cation, requirements of the product. extensions or alterations must be carried out on the product. © elero GmbH US+CA | 3...
  • Page 4: Safety Instructions On Transport, Assembly And Installation

    This may lead to different operating properties e. g.  The smallest internal tube diameter for the winding shaft when approaching end positions. is 36 mm for RolTop type S, 47 mm for RolTop type M Installation and 58 mm for RolTop type L.
  • Page 5: Mechanical Mounting

    ►Before initial commissioning, check the correct connec- Important tion of the PE conductor. Damage to or destruction of the RolTop due to ingress of On delivery (factory settings), the RolTop is in commissio- humidity. ning mode. ►For devices with protection class IP44, the customer- ►It is necessary to set the end positions...
  • Page 6: Connection Example, Roltop 120 V / 60 Hz

    The relief function at the upper limit stop is activated. 5.6.3 Relief function at the lower stop Fig. 5 Circuit diagram RolTop 120 V / 60 Hz and Wiring when using a Hirschmann plug connection For option C (refer to section 5.6.8) STAS-3 and option D (refer to section 5.6.9):...
  • Page 7: Four Options For End Position Settings

    Press the DOWN button ▼ again, until the fabric has reached the desired lower end position. Fig. 7 Options of end position settings for RolTop The drive system starts, stops briefl y and starts again (as long as the button is pressed).
  • Page 8: Option D

    Corrections can be made with the buttons ▲ and tion cable is ▼. pressed). ② Keep the DOWN button ▼ pressed until the drive Fig. 12 RolTop troubleshooting system stops automatically. The upper end position is set. Servicing ③ Press the DOWN button ▼ again, until the fabric has reached the lower end position (to bottom limit The RolTop is maintenance-free.
  • Page 9 Einhaltung folgender Richtlinien und Normen berücksichtigt: • EMV-Richtlinie 2004/108/EG • Niederspannungsrichtlinie 2006/95/EG DIN EN 60335-2-97 (VDE 0700-97):2009 • DIN EN 14 202:2004 Beuren, 31.05.2012 Ralph Trost -CE-Beauftragter-, -Doku-Bevollmächtigter- Fig. 13 EC Declaration of Conformity RolTop type S and M © elero GmbH US+CA | 9...
  • Page 10 Technical data and dimensions Type RolTop M10/17 120 V, 60 Hz Max. torque [Nm] Limit switch range in turns Length A [mm] Length B [mm] Weight [kg] Noiseless soft brake ▪ Speed [rpm] Power [W] Current [A] 1,20 Operating Voltage [V]...

This manual is also suitable for:

Roltop m10Roltop m1734 227 6001

Table of Contents