Summary of Contents for Canon Microfilm Scanner 300
Page 1
Be sure to read this instructions before you use the equipment. ENGLISH Keep this instructions on hand for reference to ensure optimum preformance.
INTRODUCTION These instructions describe the operating procedures for the Canon Microfilm Scanner 300. After you set up the unit, keep this manual in a convenient location so you can find it when you need it.
CONTENTS INTRODUCTION ... 1 Conventions ... 2 BEFORE YOU BEGIN ..5 Work Safety!... 5 Choosing a safe location ... 5 Power supply ... 7 Daily handling ... 8 Features of the Microfilm Scanner 300 ... 10 About operation modes ... 11 Unpacking: What's in the box? ...
BEFORE YOU BEGIN ... To ensure safe, efficient operation, read the follow precautions and recommendations before you choose a location and set up the system. Work Safety! Choosing a safe location I To ensure adequate space for ventilation, operation, and mainte- nance, make sure there is enough space around the system on all 10cm sides.
Page 8
I BEFORE YOU BEGIN ... I I Avoid areas like laboratories where fumes from ammonia, acetone, or other volatile chemicals are present. Never use any kind of volatile, flammable spray near the unit. I Never set up the unit in an area where flammable substances like alcohol, thinner, or other organic chemicals are present.
I BEFORE YOU BEGIN ... I Power supply If you have any questions about the power source at your work site, contact your supplier or the power com- pany. I The unit should have an independent power source that is not shared with any other electrical device.
If any liquids or metal objects fall into the scanner, immediately switch the scanner off, unplug the power cord and contact an authorized Canon dealer or service center. I Do not set up the scanner in dusty or humid locations as this could result in an electric shock or fire.
Page 11
I BEFORE YOU BEGIN ... I I Use only a power supply having the rated voltage. The use of other voltages could result in a fire or electric shock. I Always unplug the power cord by grasping the plug itself. Pulling on the power cord can damage the cord so that the core wires are exposed or snapped and could cause a fire or electric shock.
I BEFORE YOU BEGIN ... I Features of the Microfilm Scanner 300 ❏ Space saving The economical design of this compact film scanner requires less space on your desk or work table. ❏ Automatic film polarity detection The unit automatically detects the presence of negative film or positive film and sets itself accordingly.
I BEFORE YOU BEGIN ... I About operation modes The following operating modes are available with this scanner. Select one of the following modes according to your system envi- ronment before using the scanner. For details, contact your ser- vice representative. ❏...
If anything is missing, contact your sup- plier. I Microfilm Scanner 300 I Setup CD ISIS/TWAIN Driver CapturePerfect I Power cord I Instructions (This manual) I Canon Software License Agreement I Warranty Card (U.S.A. and Canada only)
I BEFORE YOU BEGIN ... I Operation panel Provides keys that allow you to perform settings for image adjustment or film mode selection. DIN connector Allows you to connect a cable for the Autocarrier 100C, 100R, 100M, FS Controller I or Roll/Fiche carrier 200.
I BEFORE YOU BEGIN ... I Preparing the carrier This is a list of all the carriers that can be installed and used with the Microfilm Scanner 300. For more details about these options, contact your supplier. For details about installation and opera- tion, refer to the instructions provided with each auto carrier.
I BEFORE YOU BEGIN ... I Preparing the lens The following types of lenses are available. Fixed lens EX7 (x7) Zoom lenses EZ01 (x9.5 to x16) EZ02 (x16 to x32) EZ03 (x30 to x55) EZ04 (x10 to x24) Checking the lens label Report to your dealer if the lens label attached to a lens that you intend to use differs from a sample shown in the figure below.
Page 19
Light adjustment dial I BEFORE YOU BEGIN ... I 2. Slide the other lens into the unit. If you are using the FS Controller I, before you insert the lens, remove the bottom cover of the lens as shown in the illustration. Make sure you keep the cover and install it on the lens again after it is removed from the unit.
I BEFORE YOU BEGIN ... I Preparing the computer (scanner mode) In order to use the Micofilm Scanner 300, your computer must satisfy the following system requirements: I IBM PC/AT-compatible that meats the following specifications: • Intel Celeron 733MHz or faster •...
Connecting the computer Connection of the SCSI cable to the main unit and the specifica- tion of the SCSI ID and other setting should be done by the super- vising service personnel. To change the SCSI ID or any other connection settings, please contact your service provider.
I BEFORE YOU BEGIN ... I Canon Fileprint 250 Canon Fileprint 450 Preparing optional printer (for the DMP mode) This is a list of all the optional printer that can be installed and used with the Microfilm Scanner 300. For more details about these options, contact your supplier.
1 Negative/Positive key 2 Trimming/Border key 3 Brightness indicator 4 Brightness adjustment keys 5 Print/Error Display 6 Print number setting key 7 Clear/Stop key 8 Start key I BEFORE YOU BEGIN ... I Operation panel and keyboard keys Operation panel keys This is a summary of the keys on the operation panel.
I TURNING THE POWER ON/OFF I TURNING THE POWER ON/OFF Follow the procedures described below when turning the power on and off. Turning the power on Follow the procedure below to turn the unit on. If an FS Controller III is installed on the scanner, switch the FS Controller III on first.
I TURNING THE POWER ON/OFF I Scanner recognition If you are using Windows 95/98/Me/2000 or Windows XP, then the first time that you turn on your computer after connecting this scanner to your computer, Windows Plug and Play automatically displays a screen prompting you to install the scanner driver. Fol- low the instructions on the screen to proceed with the installation.
Page 26
I TURNING THE POWER ON/OFF I I If you are using Windows 2000 Professional, the “Found New Hardware Wizard” dialog box appears. 1. Click the Next button to proceed to the “Install Hardware De- vice Drivers” screen. 2. Select “Search for a suitable driver for my device (recom- mended)”...
I ABOUT THE SOFTWARE I ABOUT THE SOFTWARE Before installing the software, be sure to open and read the Readme.txt file on the setup disc. The setup disc included with the scanner contains the following software: I ISIS/TWAIN driver This driver allows this scanner to be used with ISIS-compatible application software or TWAIN-compatible application software.
I ABOUT THE SOFTWARE I 4. In the Open box, type “D:\Driver\Setup.exe” (where “D” is the drive letter assigned to your CD-ROM drive) and then click the OK button. The Installer starts. 5. Follow the instructions on the screen and complete the instal- lation process.
The ISIS/TWAIN driver help menu describes how to use the ISIS/TWAIN driver. To access the ISIS/TWAIN driver help, click Start - Programs (when using Windows XP, click All Programs) - Canon Document Scanner - Canon MS300/350 Help, or click the Help button displayed in the dialog box. Using CapturePerfect Follow the procedure described below to start and close CapturePerfect.
I ABOUT THE SOFTWARE I About the Reader-Printer mode When the scanner is set to the Reader-Printer mode, all the set- tings and operation of the scanner must be performed through the operation panel on the main body. For how to operate the scan- ner, see “Setting the scanner”...
Page 31
I ABOUT THE SOFTWARE I I Exiting the Reader-Printer mode 1. To change settings of the Reader-Printer mode, click the in the task tray with the right mouse button, then click “Exit Reader- Printer mode.” 2. Again, click the icon in the task tray with the right mouse button, then click “Exit application.”...
Page 32
I ABOUT THE SOFTWARE I 3. Click the “Start” button, and then click “Program” (when using Windows XP, “All programs”) – “CapturePerfect” – “Multi Scan Start.” “CapturePerfect” starts up in the Reader-Printer mode. • When the Reader-Printer mode starts up, the CapturePerfect main screen is going to reside in the task tray as the icon with the SCSI ID that the...
If you are using Windows XP, the “Add or Remove Programs” dialog box is displayed. 3. Select “Canon MS300/350” or "CapturePerfect" from the list, and then click the Add/Remove button. If you are using Windows XP, click the Change/Re- move button.
I SETTING THE SCANNER I SETTING THE SCANNER In the Scanner mode, the image projected on the scanner’s screen can be saved by the connected personal computer, or printed out through a printer connected to the PC. Actual settings and opera- tions for scanning differ depending on the application you use.
I SETTING THE SCANNER I Selecting the polarity This setting selects the film polarity (possitive or negative). Press the Negative/Positive key on the operation panel to select the film polarity. Negative Prints positive from negative film. Positive Prints positive from positive film. A Auto Automatically detects the type of film in use and prints a positive image.
I SETTING THE SCANNER I Trimming/border removal settings When an image on negative film is scanned and projected onto the scanner screen, the area outside the image appears as a black border around the image. The Automatic Border Removal func- tion can be used to remove this black border around the scanned image.
I SETTING THE SCANNER I For example, the illustration shows the vertical set for 4 and the horizontal set for 7. The shaded area is the area trimmed and se- lected for scanning. 3. To save the setting, press the Border Button. The setting remains in effect even after the power is turned off and turned again.
I Printing (DMP mode) I Printing (DMP mode) The following describes the printing procedure in the DMP mode. 1. Make necessary settings on the main unit. 2. Select the paper size that you want to print on. I Using the Fileprint 250 If using the Fileprint 250, select paper size set on the Paper Tray.
Page 39
I Printing (DMP mode) I 3. Set the number of prints that you want to make (1 to 99). Press the Print Number Setting key on the operation panel or the operation keyboard to set the number of prints. If you press the plus (+) key, the number increases, and if you press the minus (–) it decreases.
I USER MODE I USER MODE In the user mode, you can arbitrarily change the settings of the following features: • Power saver mode • Hi-speed scanning mode • Scanning resolution • Cleaning mode • Switching the operation modes (DMP mode/Scanner mode) User mode setting 1.
• Default of the power saver mode at factory shipping is set to so that the unit switches into the power saver mode if not operated more than 15 minutes. • The power saver mode can be canceled by any key operation.
I MAINTENANCE AND TROUBLESHOOTING I MAINTENANCE AND TROUBLESHOOTING This part of the manual describes how to replace the halogen lamp, cleaning the scanner and dealing with errors. Regular scanner maintenance is essential to eusure optimum performance and a long service life from your scanner. Replacing the lamp The lamp projects the film image onto the screen, and the proce- dure for replacing the lamp is described below, along with some...
Page 43
• Use only Canon-specified lamps as replacements. • Take care not to touch the bulb in the new lamp.
I MAINTENANCE AND TROUBLESHOOTING I Field lens Routine cleaning Use the routine cleaning procedures described below to keep the scanner components clean and ensure optimum performance. Cleaning the screen and main unit Use a cloth slightly dampened with water or mild detergent to clean any soiling off the scanner screen and casing.
I MAINTENANCE AND TROUBLESHOOTING I Cleaning mode After changing the toner cartridge for the Fileprint 450, you must clean the fixing rollers of the Fileprint 450. The following describes the cleaning procedure for the fixing roll- ers of the Fileprint 450. For details on how to handle the Fileprint 450, refer to the Fileprint 450 Instruction Manual.
I MAINTENANCE AND TROUBLESHOOTING I Problem Screen does not come on, even after turning on the power switch. The screen brightness is uneven or the screen is too dark. Image is out of focus. Image is skewed. Splices are seen on the image after a few scans. • This is one of the specifications to complement insufficient per- After pressing the start key, scan will not start.
Error Number Meaning The lamp installed in the scanner has burned out. The lamp unit is not correctly in- stalled in the scanner. Error Number Meaning After removing a piece of jammed paper, a sheet of paper is still jammed in the printer. A sheet of paper has jammed inside the printer.
I When you cannot clear a service call error Make a note of the error code and the nature of the problem. Then switch off the scanner and any peripheral units such as the carrier, unplug the power cord and contact an authorized Canon service technician.
Microfilm Scanner 300 Main Unit Type Desktop digital microfilm scanner Screen 300 mm x 300 mm Scanning method 600 dpi digital scanning Film Negative, Positive, Negative/Positive auto switching Lens magnification x7,x9.5-x16, x16-x32, x30-x55, x10-x24, x20-x48 Light source Halogen lamp (20V 150W) Film Type Silver film, Diazo film, (blue/black)
I INDEX I Adjusting ... 32 AE ... 33 Auto ... 33 Border removal ... 34, 35 Brightness ... 33 CapturePerfect ... 10 Carrier Autocarrier 100C ... 15 Autocarrier 100M ... 15 Autocarrier 100R ... 15 Fiche Carrier 190RII ... 15 FS Controller I ...
Page 52
CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y.11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180EG AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC.