Related Manuals for Canon SCANFRONT M11058
Summary of Contents for Canon SCANFRONT M11058
-
Page 1: Setup Guide
Setup Guide Read This First Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference. - Page 2 ScanFront 220P: Model M11062 Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • imageFORMULA is a trademark of Canon Electronics Inc.
- Page 3 Portions of this software are based in part on the work of the Independent JPEG Group. Copyright 2007 by CANON ELECTRONICS INC. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical,...
-
Page 4: Table Of Contents
ScanFront Setup Overview ... 7 1. Checking the Supplied Accessories ... 8 2. Removing the Packing Materials and Attaching the Feed Roller... 9 3. Installing the Scanner and Connecting to a Network ... 12 Interfaces... 12 Connecting the AC Adapter... 13 Connecting the Network Cable... -
Page 5: Introduction
Thank you for purchasing the Canon imageFORMULA ScanFront 220/220P network scanner. Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its many functions. After reading this manual, store it in a safe place for future reference. -
Page 6: Manuals For The Scanner
❏ Manuals for the Scanner The following manuals are provided with the Canon ScanFront 220/220P. Be sure to read these manuals thoroughly before using the scanner. Setup Guide (This Manual) Describes the procedure for setting up the scanner for scanning. Set up the ScanFront in accordance with the Setup Guide. -
Page 7: Important Safety Instructions
Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. ❏ Installation Location The performance of this scanner is affected by the environment in which it is installed. Make sure that the location where the scanner is installed meets the following environmental requirements. -
Page 8: Moving The Scanner
Model: MG1-3968 ● If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information. ❏ Moving the Scanner ● When moving the scanner, always hold it with both hands to avoid dropping it. - Page 9 Then, contact your local authorized Canon dealer or service representative for further information. ■ Do not drop the scanner, or subject it to impact or strong shock. Should the scanner ever become damaged, immediately turn the power OFF, and disconnect the power plug from the power outlet.
-
Page 10: About The Fingerprint Sensor (Scanfront 220P Only)
❏ Disposal ● Prior to disposing of the scanner, initialize the scanner to ensure that the registered data is deleted. ● When disposing of the scanner, make sure to follow all local ordinances and laws or consult with the retailer who sold you the scanner. -
Page 11: Scanfront Setup Overview
AC adaptor and network cable. Turning the Power ON and OFF (See p. 14) Use the power switch to turn the scanner ON, and press [Power off] on the touch panel to turn it OFF. Configuring the Scanner Settings (See p. 15) -
Page 12: Checking The Supplied Accessories
Checking the Supplied Accessories After unpacking the scanner, confirm that the following accessories are included. In the unlikely event that any of these accessories are missing or damaged, contact your local authorized Canon dealer. ScanFront 220 (standard model) ScanFront 220P... -
Page 13: Removing The Packing Materials And Attaching The Feed Roller
Removing the Packing Materials and Attaching the Feed Roller Remove all of the packing materials protecting the scanner, and attach the feed roller. Remove the orange tape (3 pieces) securing the outer case. Gently open the document eject tray. Pull the lock lever toward you and then fully open the panel unit. - Page 14 Align the notch in the shaft of the roller with the shaft of the scanner, and place the feed roller into position. Move the lock lever in the direction of the arrow, then insert it into the hole in the feed roller.
- Page 15 Gently close the panel unit. Press on both sides of the unit until you hear a click, which indicates the unit is locked. Gently close the document eject tray.
-
Page 16: Installing The Scanner And Connecting To A Network
Installing the Scanner and Connecting to a Network Before setting up the scanner, you need to move it to the installation site, and connect the AC adaptor and network cable. IMPORTANT For information on installation safety, see p. 3. ❏ Interfaces The interfaces are located on the right side of the scanner. -
Page 17: Connecting The Ac Adapter
Follow the procedure shown below to connect the AC adapter. CAUTION Make sure to use only the AC adapter and power cord included with the scanner. a Connect the power cord and AC adapter. b Insert the plug of the AC adapter into the power connector. -
Page 18: Turning The Power On And Off
Turning the Power ON and OFF Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF. ❏ Turning the Power ON Press the power switch to turn the scanner ON. The power indicator lights, and the Home screen or the login screen appears. -
Page 19: Configuring The Scanner Settings
The following items are only a few of the availavle settings. The necessary configuration differs, depending on the scale of the network environment in which you plan to use the scanner. To use the scanner with the minimum required settings, you must register addresses to the Shared Address Book in addition to configuring the [Network setting] items. -
Page 20: Network Settings
IP address needed to connect the scanner to a network. IMPORTANT • The device name is the name used to identify the scanner on the network and is set to the 14 alphanumeric characters of the SF+MAC address by default. When changing this setting, make sure to select a unique name that is different from those of all other devices. - Page 21 Enter the new device name (or IP address), and press [OK]. IMPORTANT • The device name is the name used to identify the scanner on the network. When changing this setting, make sure to select a unique name that is different from those of all other devices.
-
Page 22: Configuring The Date And Time And Confirming The Time Zone
Turn the scanner ON. Log in to [Administrator setting], open the network settings, and confirm the IP address. - Page 23 Click [Device Configuration]. The [Device Configuration] screen appears. Check the [Language/Timezone] setting. Hint To change the setting, click [Language/Timezone] or [Setting]. Language/Timezone Setting Screen IMPORTANT • If the correct time zone is not set, the time stamps that are saved for the send time of e-mail messages, and for the saved image files will be incorrect.
-
Page 24: Mail Server Settings
❏ Mail Server Settings To send scanned images via e-mail, open the Server Settings screen from the Web Menu and register a mail server. For details, refer to “Server Settings” on p. 4-27 of the ScanFront 220/220P INSTRUCTIONS (electronic manual). -
Page 25: Scanning Procedure
This section gives an overview of the procedure for sending scanned images from the Home screen. For more details, refer to the Operation Guide or the ScanFront 220/220P INSTRUCTIONS (electronic manual). Place a document in the scanner. Select a transfer destination by pressing a destination button. - Page 26 Confirm that the selected address has a check mark, and press [Next]. The [Scan / Delivery Options] screen appears. Confirm the scan settings, and press [Start]. Scanning starts, and stops when the document has been scanned. • Press [Abort] to cancel the scanned images and return to the Scan/Delivery Options screen.
- Page 27 An address confirmation message appears. Confirm the address and press [OK] to send the scanned image. The scanner sends the image file and returns to the Home screen. Hint The screen that appears after images are sent can be selected...
- Page 28 CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC.