Subscribe to Our Youtube Channel
Related Manuals for Heatsail BEEM
Summary of Contents for Heatsail BEEM
- Page 1 B E E M ® W I T H M I S T I N G M A N U A L For the most recent version of this manual, check our website. Do not discard this manual, as it contains your device’s serial number.
- Page 3 H A ND L EI D I N G US E R M A NUA L M OD E D’ EMP LO I BET R I E B SA N L EI T U N G...
- Page 4 If you resell the BEEM with misting system, transfer it to another user or leave it behind when relocating, the manual must be made available to the new user.
- Page 5 User manual Operating, maintenance and installation. Note Read this manual carefully before using the device! Do not throw this manual away; it contains the serial number of your device! User manual...
- Page 6 Heatsail is not responsible for damage caused by an ungrounded device. The installation of the misting system of the BEEM requires a mains connection of 110-120V: the connection must be properly implemented in accordance with the applicable IEC-CEI standards.
-
Page 7: Maintenance
Maintenance 3.1 General cleaning Cleaning of the parts and the hood of the machine may only been done with a dry and soft cloth. Do not use detergents. All volatile and flammable detergents are not allowed. The nozzles are consumer goods, replace them with new ones as soon as they are blocked. -
Page 8: Warranty Conditions
Any defective goods will be reveiwed by Heatsail or an authorized Heatsail distributor. Once Heatsail has deemed a fault as a warranty situation, the Heatsail unit(s) will be brought to Heatsail or a local distributor for repair and returned in a timely manner. -
Page 9: Applicable Law
Damage caused through normal wear and tear. 4.3. What to do in the event of a defect? In case of a fault, you must contact Heatsail or an authorized distributor immediately (and no later than two months after the fault was first identified) for a repair or replacement. - Page 10 Assembly and wiring instructions Open the box and follow these instruction guidelines for a quick installation. You’ll find this inside: pump flexible high-pressure hose of 197 inches (5m) manual Below you will find an overview. Heatsail BEEM® with misting...
- Page 11 S T E P 1 Open the box carefully. Place the box on a flat surface and carefully open the cardboard box. S T E P 2 A water filter is recommaned. Connect the water filter to the water tap. S T E P 3 Take off the handle.
- Page 12 S T E P 4 Insert the flexible high-pressure hose (1) of the BEEM through the provided pipe/opening. Connect the flexible high-pressure hose (1) to the machine using the left connection. You can use an L-connector (3) if you have sharp corners.
-
Page 13: Operation
After plugging the pump into a suitable outlet and turning the water tap halfway open, you can turn on the pump. You have two options to use the fogging system of your BEEM; either you use the remote control or you use the buttons below. These work as follows:... -
Page 14: Troubleshooting
The quality of the oil is not suitable for the machine. • The machine has to work too hard reduce the pressure. The pump and connectors are leaking • Replace the oil. • Check whether a nut and/or bolt is loose. Heatsail BEEM® with misting... - Page 15 BEEM® TIMELESS LIGHTING WITH HEATING AND MISTING FOR YOUR GARDEN OR TERRACE RUSTPROOF & LOW ENERGY USAGE MINIMUM OF MAIN- WEATHERPROOF ZERO CO2 EMISSION TENANCE User manual...
- Page 16 Prins Boudewijnlaan 7 Unit A 08 2550 Kontich Belgium +32 3 502 99 88 sales@heatsail.com www.heatsail.com US Office HEATSAIL USA Inc. 10440 N Central Expressway, Suite 800 Dallas, Texas 75231 United States UCM@heatsail.com www.heatsail.com/usa S E R I A L N U M B E R...
Need help?
Do you have a question about the BEEM and is the answer not in the manual?
Questions and answers