Advertisement
Quick Links
Flex
QAS Nail Drag for Sand Pro
Unit
Model No. 08762—Serial No. 314000001 and Up
Introduction
This product complies with all relevant European
directives. For details, please see the separate
product specific Declaration of Conformity (DOC)
sheet.
You may contact Toro directly at www.Toro.com
for product safety and operation training materials,
accessory information, help finding a dealer, or to
register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.
1
illustrates the location of the model and serial
numbers on the product. Write the numbers in the
space provided.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
Nail-drag bracket
Spring bracket assembly
Carriage bolt (3/8 inch)
Locknut (3/8 inch)
Bolt (1/2 x 1 inch)
Locknut (1/2 inch)
Groomer
Side guard
Screw (1/4 x 1-3/4 inches)
Locknut (1/4 inch)
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
™
Groomer Kit
Figure
Qty.
1
2
12
12
1
1
1
2
4
4
Register at www.Toro.com.
®
/Infield Pro
®
3040 or 5040 Traction
1. Location of the model and serial numbers
Model No.
Serial No.
Install the groomer onto the nail drag.
Original Instructions (EN)
All Rights Reserved *3394-565* B
Printed in the USA
Form No. 3394-565 Rev B
Installation Instructions
Figure 1
Use
g026745
Advertisement
Related Manuals for Toro Flex 08762
Summary of Contents for Toro Flex 08762
- Page 1 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Model No. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure Serial No. illustrates the location of the model and serial numbers on the product.
- Page 2 Installing the Groomer onto Removing the Nails and the Plates Start the machine and raise the attachment lift the Nail Drag so that the nail drag is up off the ground. Remove the lynch pins (Figure Attaching the Spring Bracket Assemblies to the Nail-drag Bracket Note:...
- Page 3 Mounting the Nail-drag Bracket to Install the bolt (1/2 x 1 inch) through both holes, and secure the bolt with the nut (1/2 inch); refer the Nail Drag Figure Align the front hole in the center tab on the Note: Install the nut on the bolt until it is nail-drag bracket to the hole in the rectangular finger-tight and wait to tighten it until after you...
- Page 4 Installing the Groomer onto the Install a carriage bolt (3/8 x 3/4 inch) up through the bottom of each hole, and secure each Spring Bracket Assemblies carriage bolt with a nut (3/8 inch); refer to Figure Remove 4 screws and nuts as shown in Figure Note: Install all the nuts and bolts until they are...
-
Page 5: Operation
Installing the Side Guards onto Operation the Nail Drag Stowing the Groomer Align the holes in a side guard with the holes in the side of the frame of the nail drag as shown Remove the 2 clevis pins (Figure 11). -
Page 6: Operating Tips
Operating Tips To increase the usable life of the groomer, you can remove the rubber trowel, flip it over, and install it again. Remove the 10 nuts and the 10 bolts securing the 2 support straps to the rubber trowel (Figure 12). - Page 7 Notes:...
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.