Page 2
SERVICE MANUAL 570ST 48048556 16/09/2016...
Page 3
Link Product / Engine Product Market Product Engine 8045.45.748 570ST Four-Wheel Drive (4WD), Asia Pacific 72kW Tier 3, Side shift 570ST Two-Wheel Drive (2WD), Latin America 8045.45.748 72kW Tier 3, Side shift 570ST Two-Wheel Drive (2WD), Australia New Zealand 8045.45.748...
Page 4
Contents INTRODUCTION Engine..................10 [10.001] Engine and crankcase ............. 10.1 [10.254] Intake and exhaust manifolds and muffler .
Page 5
Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
Page 6
[35.104] Fixed displacement pump ............35.3 [35.359] Main control valve .
Page 7
[55.518] Wiper and washer system............55.4 Front loader and bucket...............
INTRODUCTION Safety rules 570ST ANZ --- APAC --- LA --- MEA Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury.
NOTICE: Extreme working and environmental conditions require shortened service intervals. Use Case fluids, lubricants, and filters for the best protection and performance of your machine. All fluids, lubricants, and filters must be disposed of in compliance with environmental standards and regulations. Contact your Dealer with any questions regarding the service and maintenance of this machine.
INTRODUCTION Safety rules - Ductile iron 570ST ANZ --- APAC --- LA --- MEA DANGER Altering cast ductile iron can cause it to weaken or break. Before you weld, cut, or drill holes on any part of this machine, make sure that the part is not cast ductile iron.
INTRODUCTION Safety rules - Ductile iron 570ST ANZ --- APAC --- LA --- MEA DANGER Improper operation or service of this machine can result in an accident. Any unauthorized modifications made to this machine can have serious consequences. Consult an authorized dealer on changes, additions, or modifications that may be required for this machine.
INTRODUCTION Safety rules 570ST ANZ --- APAC --- LA --- MEA Unless otherwise instructed, always perform these steps before you service the machine: 1. Park the machine on a flat, level surface. 2. Place the backhoe in the transport position with the swing lock pin installed for transport.
INTRODUCTION Safety rules - Ecology and the environment 570ST ANZ --- APAC --- LA --- MEA Soil, air, and water are vital factors of agriculture and life in general. When legislation does not yet rule the treatment of some of the substances required by advanced technology, sound judgment should govern the use and disposal of products of a chemical and petrochemical nature.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case of damages caused by parts and/or components not approved by the manufacturer.
INTRODUCTION Basic instructions 570ST ANZ --- APAC --- LA --- MEA WARNING Explosive gas! Batteries emit explosive hydrogen gas and other fumes while charging. Ventilate the charging area. Keep the battery away from sparks, open flames, and other ignition sources. Never charge a frozen battery.
INTRODUCTION Basic instructions - Fuse and relay locations 570ST ANZ --- APAC --- LA --- MEA The machine is equipped with a fuse located on the side console. Side console box 1. Turn the thumb screws (1) to loosen the panel cover (2) for the fuse box.
INTRODUCTION Basic instructions 570ST ANZ --- APAC --- LA --- MEA WARNING Crushing hazard! If you service the machine with the loader lift arms raised, always use the support strut. Remove the retaining pin and place the support strut onto the cylinder rod. Install the retaining pin into the support strut.
Page 21
INTRODUCTION Lower supported loader lift arms: 1. Raise the lift arms so that the end of the support strut no longer rests on the cylinder. 2. Shut down the engine. RCPH10TLB227AAF 3. Remove the retaining pin from the support strut. 4.
INTRODUCTION Basic instructions 570ST ANZ --- APAC --- LA --- MEA Open the hood: 1. Shut down the engine. 2. Turn the handle (1) counter-clockwise to release the hood latch. PTIL13TLB1558AB 3. Lift the hood and rotate forward. PTIL12TLB0559AB NOTICE: To avoid damage to the hood parts, always close the hood before moving the loader.