IBASE Technology BYTEM-103-PC User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

www.ibase.com.tw

BYTEM-103-PC

User Manual

IBASE Technology Inc.

Table of Contents

Summary of Contents for IBASE Technology BYTEM-103-PC

Page 1 BYTEM-103-PC User Manual IBASE Technology Inc.
Page 3 BYTEM-103-PC User Manual Copyright © 2013 IBASE Technology Inc. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of IBASE Technology INC.
Page 4: Table Of Contents
BYTEM-103-PC User Manual Table of Contents Safety Information ....................iii Setting up your system ....................... iii Care during use ........................iv Acknowledgments ....................... v CHAPTER 1 INTRODUCTION ..................1 1.1 General Description ....................... 1 1.2 System Specification ...................... 2 1.2.1 Hardware Specifications ..................... 2 1.2.2 Dimensions .........................
Page 5: Safety Information
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -30° C OR ABOVE 70° C. THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 6: Care During Use
BYTEM-103-PC User Manual Care during use  Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system.  When the system is turned off, a small amount of electrical current still flows.
Page 7: Acknowledgments
FINTEK is a registered trademark of FINTEK Electronics Corporation.  REALTEK is a registered trademark of REALTEK Electronics Corporation.  All other product names or trademarks are properties of their respective owners. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 9: Chapter 1 Introduction
10/100M LAN with M12 connector and one RS-232/422/485 port. The unit is equipped with a front bezel that has IP65-rated protection. The BYTEM-103-PC supports 24V DC power input and optional 48V DC, 72V DC & 110V DC input and is EN50155 certified, which makes it ideal for railway or any other industrial applications.
Page 10: System Specification
BYTEM-103-PC User Manual 1.2 System Specification 1.2.1 Hardware Specifications Model Name BYTEM-103-PC System Mainboard IB897 ® Intel Atom E3845 (Quad-Core @ 1.91 GHz) ® Chipset Integrated in Intel Atom Memory 2x DDR3L SO-DIMM, up to 8GB, Default DDR3L 4GB(4GBx1) 1 x USB 3.0 flag type blue color I/O Interface 1 x USB 2.0 Type A flag type...
Page 12 BYTEM-103-PC User Manual...
Page 13: I/O View
IBASE Technology Inc. 1.2.3 I/O View BYTEM-103-PC I/O Side M12 Power Input Connector Pin 1: NC Pin 2: Power+ Pin 3: Ground Pin 4: Power- Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 14 BYTEM-103-PC User Manual M12 10/100M LAN Port Pin 1: LAN TX+ Pin 2: LAN RX+ Pin 3: LAN TX Pin 4: LAN RX-...
Page 15 These buttons are used to adjust the panel brightness (0~100). There are 8 increments. Screen On/Off This switch is used to turn off or turn on the screen. It does not work when the system is powered off. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 16: Accessory List
BYTEM-103-PC User Manual 1.3 Accessory List Part No. Description Quantity Power external cable 1 pc LAN external cable 1 pc Driver CD 1 pc Optional 24V power adaptor & power cord 1 pc 1.4 Installation 1.4.1 Installing HDD/SSD 1. Loosen the screw as shown in the picture.
Page 17: Chapter 2 Motherboard Introduction
Intel® I210IT PCIe Gigabit LAN x 2 Intel® Atom SoC built-in USB host controller Supports USB 2.0 x 4 ports; USB 3.0 x 1 port, extra USB 2.0 x4 ports (Thru SMSC HUB USB2514) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 18 BYTEM-103-PC User Manual Serial ATA Intel® Atom SoC built-in SATA II controller, supports 2 ports ® Audio Intel Atom SoC built-in HD audio controller + Realtek ALC269QHD Codec w/ class-D speaker amplifier (2.3W per channel @ 5V power supply) [7mm x 7mm @ 48-QFN]; support 2-channel audio out + amp LPC I/O Nuvoton NCT5523D [64-pin LQFP, 7x7x1.4mm]...
Page 20: Installing The Memory
BYTEM-103-PC User Manual 2.2 Installing the Memory The IB897 board supports two DDR3L memory sockets for a maximum of 8GB. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the...
Page 21: Setting Jumpers
Jumpers are used on IB897 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following shows the jumpers/connectors on IB897. Jumper Locations on IB897 Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 22 BYTEM-103-PC User Manual JP2: LVDS Panel Brightness Control Selection Brightness Control (PWM mode) Open 3.3V Close 5V (default) J5: LVDS Panel Power Selection Setting Panel Voltage Pin 1-2 3.3V (default) Short/Closed Pin 2-3 Short/Closed...
Page 23 JP5: Clear ME Contents Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear ME Register Short/Closed JP6: Clear CMOS Contents Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear CMOS Short/Closed Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 24 BYTEM-103-PC User Manual Connector Locations on IB897-I45/I27/I15 Bottom Side CN3: USB3.0 Connector CN4, CN5: Gigabit LAN Connector CN4: Intel® I210IT Connector CN5: Intel® I210IT Connector CN6: USB2.0 Connector CN7: DP Connector...
Page 25 COM1 is jumper-less for RS-232, RS-422 and RS-485 and is to be configured with BIOS Selection. Pin # Signal Name RS-232 R2-422 RS-485 DATA- DATA+ Ground Ground Ground CN9: Micro SD (3.3V) Connector SW1: Power Switch [For IB897-I45/I27/I15] Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 26 BYTEM-103-PC User Manual LED1: Power LED and HDD LED Connector [For IB897-I45/I27/I15] The green LED at the bottom is power LED. The red LED on top is the HDD LED. Pin # Pin # Signal Name Signal Name VCC3 HDD_LED...
Page 27 IBASE Technology Inc. CN1: SATAII /share mSATA/ Connectors CN2: SATAII Connectors SYS_FAN1: SYSTEM Fan Power Connector Pin # Signal Name Ground +12V(500mA) Rotation detection Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 28 BYTEM-103-PC User Manual J1: Audio Connector (DF11-12DP-2DSA) Signal Name Signal Name Pin # Pin # LINEOUT_R LINEOUT_L Ground JD_FRONT LINEIN_R LINEIN_L Ground JD_LINEIN MIC-R MIC_L Ground JD_MIC1 J2: Amplify Connector (JST B4B-PH-K-S ) Pin # Signal Name OUTL+ OUTL- OUTR-...
Page 29 J6: Second Channel LVDS Signal Name Pin # Pin # Signal Name TX0N TX0P Ground Ground TX1N TX1P Ground Ground TX2N TX2P Ground Ground CLKN CLKP Ground Ground TX3N TX3P Power (1A) Power Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 30 BYTEM-103-PC User Manual J9: MCU Flash Connector (factory use only) J10: SATA HDD Power Connectors (JST B4B-XH-A) Pin # Signal Name +5V(1A) Ground Ground +12V(1A)
Page 31 IBASE Technology Inc. J11: Smart Battery (JST B5B-PH-K-S ) Signal Name Pin # RST# ICHSWI# Ground SMB_DATA SMB_CLK J12: Mini PCIE Connector (share mSATA) J13: Mini PCIE Connector (Half Size) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 32 BYTEM-103-PC User Manual J14: USB 2.0 Connector (DF11-8DP-2DSA) Pin # Pin # Signal Name Signal Name Ground Ground J15: COM2/RS232 Serial Port(DF11-10DP-2DSA) Signal Name Pin # Pin # Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data...
Page 33 Signal Name Ground Green Blue DDCDATA H_SYNC V_SYNC DDCCLK N.C. J17: Digital I/O (signal level 5V) Connector (2.54mm) Signal Name Pin # Pin # Signal Name VCC (500mA) OUT3 OUT1 OUT2 OUT0 Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 34 BYTEM-103-PC User Manual J18: Board Input Power Connector (HK_WAFER396-2S-WV ) Signal Name Pin # +9V to +30V(10A) J19: Reset Switch (2mm) Signal Name Pin # Reset Switch Ground...
Page 35 IBASE Technology Inc. J20: Power Switch (2mm) Signal Name Pin # Power Switch Ground JP3: LCD Backlight Connector (JST B4B-PH-K-S ) Signal Name Pin # +12V(1A) Backlight Enable Brightness Control Ground Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 36 BYTEM-103-PC User Manual JP4: SPI Flash Connector (factory use only) JP7: Factory use only JP8: Debug 80 Port Connector (factory use only)
Page 37: Chapter 3 Bios Setup
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 38 BYTEM-103-PC User Manual 3.3 Main Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information → ← System Language [English] Select Screen ↑↓ Select Item System Date [Tue 01/20/2009]...
Page 39 Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Select ACPI sleep state the system will enter when the SUSPEND button is pressed. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 40 BYTEM-103-PC User Manual LVDS Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit Configuration Panel Color Depth 24 BIT → ← Select Screen ↑↓ Select Item LVDS Channel Type Single...
Page 41 ► Serial Port 2 Configuration F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Serial Port 1 Configuration Set parameters of serial port 1(COMA) Serial Port 2 Configuration Set parameters of serial port 2(COMA) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 42 BYTEM-103-PC User Manual H/W Monitor Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit PC Health Status Smart Fan Function Disabled SYS temp +33.0 C CPU temp +34.5 C FAN1 Speed...
Page 43 CPU Speed 1751 Mhz Enter: Select +- Change Field 64-bit Supported F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Socket 0 CPU Information Socket specific CPU Information. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 44 BYTEM-103-PC User Manual CPU PPM Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit CPU PPM Configuration → ← Select Screen EIST Enabled ↑↓ Select Item Enter: Select +- Change Field...
Page 45 Enabled / Disabled Serial Port 0 SATA Port0 HotPlug Enabled / Disabled SATA Port 0 HotPlug Serial–ATA Port 1 Enabled / Disabled Serial Port 1 SATA Port1 HotPlug Enabled / Disabled SATA Port 1 HotPlug Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 46 BYTEM-103-PC User Manual SDIO Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit SDIO Access Mode Auto → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help...
Page 47 Total Memory 4096 MB (LPDDR3) Enter: Select +- Change Field F1: General Help F2: Previous Values Memory Slot0 4096 MB (LPDDR3) F3: Optimized Default F4: Save ESC: Exit Memory Slot2 Not Present Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 48 BYTEM-103-PC User Manual 3.4 Security Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Security...
Page 49 Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options. Boot Option Priorities Sets the system boot order. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 50 BYTEM-103-PC User Manual Save & Exit Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Save & Exit Main Advanced Chipset Boot Security Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset...
Page 51: Chapter 4 Drivers Installation
4. Click Yes to accept the software license agreement and proceed with the installation process. 5. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 52: Vga Drivers Installation
BYTEM-103-PC User Manual 4.2 VGA Drivers Installation 1. Insert the DVD that comes with the system. Click Intel(R) Baytrail Chipset. Driver 2. When the Welcome screen appears, click Next to continue. 3. Click Yes to accept the license agreement and continue the installation.
Page 53: Realtek High Definition Audio Driver Installation
Chipset. Click Realtek High Definition Audio Driver. 2. On the Welcome screen, click Next to proceed with the installation. 3. InstallShield Wizard is complete. Click Finish to restart the computer and for changes to take effect. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 54 BYTEM-103-PC User Manual 4.4 I21x Gigabit Network Drivers Installation 1. Insert the DVD that comes with the system. Click Intel(R) I21x Gigabit Network Driver. 2. On the Welcome screen, click Next to proceed with the installation.
Page 56 BYTEM-103-PC User Manual 5. Click Install ready to install the program. 6. Install Wizard is complete. Click Finish to restart the computer and for changes to take effect.
Page 57: Intel Trusted Execution Engine Installation
IBASE Technology Inc. 4.5 Intel Trusted Execution Engine Installation Note :Windows 7 OS only 1. Insert the DVD that comes with the board. Click Intel(R) TXE Driver. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 58 BYTEM-103-PC User Manual 2. On the Setup Welcome screen, click Next to proceed with the installation process. 3. Click Next to accept the license agreement. 4. Installation of the Intel Trusted Execution Engine is now complete. Click Finish.
Page 59 IBASE Technology Inc. 4.6 Intel USB 3.0 Drivers Installation 1. Insert the DVD that comes with the system. Click Intel(R) USB 3.0 Driver. 2. On the Welcome screen, click Next to proceed. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 60 BYTEM-103-PC User Manual 3. Click Yes to accept the license agreement.
Page 61 IBASE Technology Inc. 4. Click Next to accept the setup progress. 5. Setup is complete. Click Finish to restart the computer and for changes to take effect. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 62: Appendix
BYTEM-103-PC User Manual Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
Page 63 Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02 IRQ 19 Intel(R) Active Management Technology - SOL (COM3) IRQ 22 High Definition Audio Controller IRQ 23 Intel(R) 8 Series/C220 Series USB EHCI #1 - 8C26 Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 64 BYTEM-103-PC User Manual C. Digital I/O Sample Code File of the NCT5523D.H //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
Page 65 SIO; SIO = Init_NCT5523D(); if (SIO == 0) printf("Can not detect Nuvoton NCT5523D, program abort.\n"); return(1); Dio5Initial(); //for GPIO20..27 Dio5SetDirection(0x0F); //GP20..23 = input, GP24..27=output printf("Current DIO direction = 0x%X\n", Dio5GetDirection()); Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 66 BYTEM-103-PC User Manual printf("Current DIO status = 0x%X\n", Dio5GetInput()); printf("Set DIO output to high\n"); Dio5SetOutput(0x0F); printf("Set DIO output to low\n"); Dio5SetOutput(0x00); return 0; //---------------------------------------------------------------------------...
Page 67 //switch to logic device 7 result = Get_NCT5523D_Reg(0xE1); return (result); //--------------------------------------------------------------------------- void Dio5SetDirection(unsigned char NewData) //NewData : 1 for input, 0 for output Set_NCT5523D_LD(0x07); //switch to logic device 7 Set_NCT5523D_Reg(0xE8, NewData); //--------------------------------------------------------------------------- unsigned char Dio5GetDirection(void) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 68 BYTEM-103-PC User Manual unsigned char result; Set_NCT5523D_LD(0x07); //switch to logic device 7 result = Get_NCT5523D_Reg(0xE8); return (result); //---------------------------------------------------------------------------...
Page 69 (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; NCT5523D_BASE = 0x2E; result = NCT5523D_BASE; ucDid = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? { goto Init_Finish; } NCT5523D_BASE = 0x00; result = NCT5523D_BASE; Init_Finish: return (result); Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 70 BYTEM-103-PC User Manual //--------------------------------------------------------------------------- void Unlock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); //--------------------------------------------------------------------------- void Lock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_LOCK); //---------------------------------------------------------------------------...
Page 71 Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D(); return Result; //--------------------------------------------------------------------------- Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 72 BYTEM-103-PC User Manual D. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock.
Page 73 WDTEnable(unsigned char); void WDTDisable(void); //--------------------------------------------------------------------------- int main (void) char SIO; SIO = Init_NCT5523D(); if (SIO == 0) printf("Can not detect Nuvoton NCT5523D, program abort.\n"); return(1); WDTInitial(); WDTEnable(10); WDTDisable(); return 0; Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 74 BYTEM-103-PC User Manual //--------------------------------------------------------------------------- void WDTInitial(void) unsigned char bBuf; Set_NCT5523D_LD(0x08); //switch to logic device 8 bBuf = Get_NCT5523D_Reg(0x30); bBuf &= (~0x01); Set_NCT5523D_Reg(0x30, bBuf); //Enable WDTO //--------------------------------------------------------------------------- void WDTEnable(unsigned char NewInterval) unsigned char bBuf; Set_NCT5523D_LD(0x08); //switch to logic device 8 Set_NCT5523D_Reg(0x30, 0x01);...
Page 75 = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; NCT5523D_BASE = 0x2E; result = NCT5523D_BASE; ucDid = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; NCT5523D_BASE = 0x00; result = NCT5523D_BASE; Init_Finish: Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 76 BYTEM-103-PC User Manual return (result); //--------------------------------------------------------------------------- void Unlock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); //--------------------------------------------------------------------------- void Lock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_LOCK); //---------------------------------------------------------------------------...
Page 77 Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D(); return Result; //----------------------------------------------------------------------- Copyright © 2013 IBASE Technology Inc. All Rights Reserved.

IBASE Technology BYTEM-103-PC User Manual

Chapter 1 Introduction

Chapter 2 Motherboard Introduction

Chapter 3 Bios Setup

Chapter 4 Drivers Installation

Appendix

Quick Links

Related Manuals for IBASE Technology BYTEM-103-PC

Summary of Contents for IBASE Technology BYTEM-103-PC

Table of Contents