Maintenance; Protecting The Environment - DeWalt DCS571E1T Manual

EnGLIsh
To Attach the Dust Bag (Fig. K)
1. While holding the saw, fit the dust bag collar
24
extraction port as shown in Figure K.
26
2. Turn the collar clockwise to lock the dust bag
in place.
To Empty the Dust Bag (Fig. K)
1. While holding the saw, turn the collar
to unlock the dust bag
2. Remove dust bag from the saw and gently shake or tap the
dust bag to empty.
3. Reattach the dust bag back onto the dust extraction port
and lock into place by turning the dust bag collar clockwise.
You may notice that all the dust will not come free from the
bag. This will not affect sanding performance but will reduce
the saw's dust collection efficiency. To restore your saw's dust
collection efficiency, depress the spring inside the dust bag
when you are emptying it and tap it on the side of the trash can
or dust receptacle.
Workpiece Support (Fig. L, M)

WARNING: To reduce the risk of serious personal injury,
support the work properly and hold the saw firmly to
prevent loss of control.
Figure L shows proper sawing position. Figure M shows an
unsafe condition. Hands should be kept away from cutting area.
To avoid kickback, ALWAYS support board or panel NEAR the
cut. DON'T support board or panel away from the cut .
ALWAYS DISCONNECT SAW BEFORE MAKING ANY
ADJUSTMENTS! Place the work with its "good" side—the one
on which appearance is most important—down. The saw cuts
upward, so any splintering will be on the work face that is up
when you saw it.

MAINTENANCE

Your D WALT power tool has been designed to
e
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
40
26
to the dust
25
26
counterclockwise
25
.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these
parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Lower Guard
The lower guard should always rotate and close freely from
a fully open to fully closed position. Always check for correct
operation before cutting by fully opening the guard and letting
it close. If the guard closes slowly or not completely, it will
need cleaning or servicing. Do not use the saw until it functions
correctly. To clean the guard, use dry air or a soft brush to
remove all accumulated sawdust or debris from the path of
the guard and from around the guard spring. Should this not
correct the problem, it will need to be serviced by an authorized
service center.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous. To
reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
WALT recommended
e