Adjusting Airflow Direction; Using The Timer - Mitsubishi Electric PLH18 AK Series Operation Manual

2. Operation
A B
A B
PL(H) Swing 30°
PK(H)* Swing 10°
PK12FK3 – 10°
PC(H) Swing 100% Horizontal
* Except PK12FK3
CHECK TEST
COOL
˚F
RUN
MODEL
˚C
DRY
SELECT
STOP AMPM
AUTO
FAN
SWING
FAN
START AMPM
HEAT CENTRALLY CONTROLLED
NOT AVAILABLE
DRY COOL
TIMER OFF
ON/OFF TEMP
AUTO FAN
CHECK SET TEMP.
HEAT
STAND BY
DEFROST
FAN AUTO STOP
MODE VANE AUTO START
1
MODE
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
REMOTE CONTROLLER
A
COOL CHECK TEST
˚F
RUN
MODEL
˚C
DRY
SELECT
STOP AMPM
AUTO
FAN
SWING
FAN
START AMPM
CENTRALLY CONTROLLED
HEAT
NOT AVAILABLE
DRY COOL
TIMER OFF
ON/OFF TEMP
AUTO FAN CHECK SET TEMP.
HEAT
STAND BY
DEFROST
FAN AUTO STOP
MODE VANE AUTO START
MODE
CHECK LOUVER h
2
TEST RUN min
SET RESET CLOCK
13
REMOTE CONTROLLER
C
CHECK TEST
COOL
RUN ˚F
MODEL
˚C
DRY
SELECT
STOP AMPM
AUTO
FAN A
SWING
FAN
START AMPM
CENTRALLY CONTROLLED
HEAT
B
NOT AVAILABLE
DRY COOL TIMER OFF
ON/OFF TEMP
AUTO FAN CHECK SET TEMP.
HEAT
STAND BY
DEFROST
FAN AUTO STOP
13
MODE VANE AUTO START
MODE
CHECK LOUVER h
2
TEST RUN min
SET RESET CLOCK
REMOTE CONTROLLER
4
All manuals and user guides at all-guides.com
C D E
C D E
45° 55° 70°
30° 60° 70°
30° 60° 70°
20° 40° 60°
F
ON/OFF –
SWING
˚F
TIMER CLOCK AUTO AUTO
FAN
START STOP SPEED FILTER
AUTO
RETURN
CHECK MODE
˚F
NOT AVAILABLE
TEST RUN
TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
SET TEMP. TIMER SET TEST RUN
1
B A
ON/OFF –
SWING
˚F
TIMER CLOCK AUTO AUTO
FAN
START STOP
SPEED AUTO FILTER
RETURN
CHECK MODE
˚F
NOT AVAILABLE TEST RUN
TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
SET TEMP. TIMER SET TEST RUN
A BC
ON/OFF –
SWING
˚F
TIMER CLOCK AUTO AUTO
FAN
START STOP
SPEED AUTO FILTER
RETURN
CHECK MODE
˚F
NOT AVAILABLE TEST RUN
TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FILTER
AIR SWEEP CHECK
SET TEMP. TIMER SET
TEST RUN

2.5. Adjusting airflow direction

The vertical air vane helps select the vertical direction of the airflow.
1 Press AIR DISCHARGE button to select the vertical airflow direction.
• Each time you press the button, the option changes are displayed on the remote
controller, as shown below.
A (swing) → B → C → D → E → A
• In cooling/drying mode with the fan speed set to LOW, every press on the button
will change the direction in the order of A, B, D, A. (C can not be set)
• If D or E is set, the angle will automatically revert to B after one hour of operation.
(Do not use D and E too often in cooling/drying mode with the fan speed set to
LOW, or condensation or dripping can occur.)
F "AUTO RETURN" should be displayed.
• When the angle setting is C in cooling mode, switching the fan speed from HIGH
to LOW will cause the angle to revert to B automatically.
• The airflow direction can not be set with UP/DOWN while the SWING setting is being used.
• The arrow indicators are alternately displayed when the air sweep is in operation,
however they are not displayed when the air sweep is not in operation.
• The left/right guide vanes of PC(H) series and the guide vane of the PK(H) serises
can be changed manually.

2.6. Using the timer

1) Set the current time
1 Press clock/timer button to display the "CLOCK" B.
Remote
controller display A
2 Each time you press button, the time increases in increments of one minute.
TIMER SET
TIMER SET
Each time you press button, the time decreases in increments of one minute.
• Press and hold the button to rapidly change the time.
• The time changes in increments of one minute → ten minutes → in units of hour; in
this order.
• Approximately ten seconds after pressing the button, the display on the remote
controller will turn off.
(For Wireless Remote Controller)
1 Press the CLOCK button using a thin stick and blink the time A.
min
h
2 Press the and button to set the current time.
3 Press the CLOCK button using a thin stick.
2) Set the time to start the unit as follows
1 Press clock/timer button to display B
2 Press button to set the time that you want the unit to start.
TIMER SET
The start time is displayed at A.
(For Wireless Remote Controller)
AUTO START
1 Press the button.
• Time can be set while the following symbol is blinking.
ON time : B START is blinking.
h min
1
2 Use the and buttons to set the desired time.
3 To cancel the ON timer, press the
2
3) Set the time to stop the unit as follows
1 Press clock/timer button to display C
2 Press button to set the time that you want the unit to stop.
TIMER SET
The stop time is displayed at A.
(For Wireless Remote Controller)
AUTO STOP
1 Press the button.
• Time can be set while the following symbol is blinking.
OFF time : C STOP is blinking.
h min
2 Use the and buttons to set the desired time.
3 To cancel the OFF timer, press the
4) Changing the set times
1 Press clock/timer button to display the time (CURRENT, START, STOP) you want
to change.
2 Press button to set the desired time.
TIMER SET
1
• When change is made to either one of a pair, e.g., AUTO START or AUTO STOP,
2
set the time you need not to change to
23:50.
(For Wireless Remote Controller)
AUTO START AUTO STOP
Press the or to cancel the timer and repeat from 2) or 3).
→ → → No Display
AUTO AUTO
CLOCK
START STOP
↑
AUTO
.
START
AUTO START
button.
AUTO
.
STOP
AUTO STOP
button.
. This display is available following